wheel DODGE RAM 1999 Service Repair Manual

"E" ABBREVIATION TABLE

“E” ABBREVIATION TABLE
ABBREVIATION DEFINITION EAC Electric Assist Choke _ EACV Electric Air Control Valve _ EBCM Electronic Brake Control Module ECA Electronic Control Assembly ECAT Electronically Controlled Automatic
Transaxle ECM Electronic Control Module ECT Engine Coolant Temperature Sensor ECU Electronic Control Unit or Engine Control
Unit EDF Electric Drive Fan relay assembly EDIS Electronic Distributorless Ignition System EEC Electronic Engine Control EECS Evaporative Emission Control System EEPROM Electronically Erasable PROM EFE Early Fuel Evaporation _ EFI Electronic Fuel Injection _ EGO Exhaust Gas Oxygen sensor (see HEGO) EGR Exhaust Gas Recirculation system _ EGRC EGR Control solenoid or system _ EGRV EGR Vent solenoid or system _ EMR Emission Maintenance Reminder Module ESA Electronic Spark Advance _ ESC Electronic Spark Control _ EST Electronic Spark Timing _ ETR Emergency Tensioning Retractor _ EVAP Fuel Evaporative System _ EVIC Electronic Vehicle Information Center EVO Electronic Variable Orifice _ EVP EGR Valve Position Sensor _ EVR EGR Valve Regulator _ EVRV Electronic Vacuum Regulator Valve Elect. Electronic _ Eng. Engine _ Evap. Evaporative _ Exc. Except _

"F" ABBREVIATION TABLE

"F" ABBREVIATION TABLE
ABBREVIATION DEFINITION F Fahrenheit (Degrees) F/B Fuse Block FBC Feedback Carburetor FI Fuel Injector or Fuel Injection FICD Fast Idle Control Device FIPL Fuel Injector Pump Lever FP Fuel Pump FPM Fuel Pump Monitor FPR-VSV Fuel Pressure Regulator Vacuum Switching
Valve FWD Front Wheel Drive Fed. Federal Ft. Lbs. Foot Pounds

"R" ABBREVIATION TABLE

"R" ABBREVIATION TABLE
ABBREVIATION DEFINITION RABS Rear Anti-Lock Brake System RAC Remote Accessory Control RAM Random Access Memory RAP Retained Accessory Power RECIRC Recirculation RED Red RH Right hand ROM Read Only Memory RPM Revolutions Per Minute RVB Rear Vacuum Break RWAL Rear Wheel Anti-Lock Brake RWD Rear Wheel Drive Recirc. Recirculate or Recirculation Reg. Regulator Rly. Relay

"S" ABBREVIATION TABLE

"S" ABBREVIATION TABLE
ABBREVIATION DEFINITION SAW Spark Angle Word _ SBC Single Bed Converter _ SBEC Single Board Engine Controller _ SC Super Charged _ SCC Spark Control Computer _ SCS Air Suction Control Solenoid _ SDM Supplemental Restraint System Diagnostic Module _ SDU SRS Diagnostic Unit _ SEN Sensor _ SES Service Engine Soon _ SFI Sequential (Port) Fuel Injection _ SIG RTN Signal Return circuit _ SIL Shift Indicator Light _ SIR Supplemental Inflatable Restraint _ SMEC Single Module Engine Controller _ SOHC Single Overhead Cam _ SOL or SoL Solenoid _ SPFI Sequential Port Fuel Injection _ SPK Spark Control _ SPOUT Spark Output Signal _ SRS Supplemental Restraint System (Air Bag) _ SS 3/4-4/3 Shift Solenoid circuit _ SSI Solid State Ignition _ STAR Self-Test Automatic Readout _ STI Self Test Input circuit _ STO Self-Test Output _ SUB-O2 Sub Oxygen Sensor _ Sen. Or Sens. Sensor _ Sol. Solenoid _ Sprchg. Supercharger _ Strg. Steering _ Susp. Suspension _ Sw. Switch _ Sys. System _

Ford Motor Co. (Taurus 3.4L SHO)
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Remove A/C compressor. Drain and measure
oil from compressor.
2) Remove pulley assembly. Using Spanner Wrench (T81P-19623-
MH), remove shaft nut and lock washer. Using a steering wheel puller,
remove clutch plate, shaft key and shim. Remove snap ring and pulley
assembly, by hand. If necessary, use a 3-jaw puller to remove pulley
assembly. Remove clutch coil wire from retaining brace on compressor.
Remove snap ring and clutch coil. See Fig. 1.
Installation
1) Install clutch coil. Ensure hole on back of clutch coil is
aligned with pin on compressor head. Install snap ring with beveled
side facing outward. Install clutch coil wire into retaining brace.
2) Slip pulley assembly onto compressor shaft and install
snap ring with beveled side facing outward. Install shim and shaft
key. Align clutch plate with shaft key and install clutch plate. Use
Hub Driven Plate Replacer (T80L-19703-F), if necessary. Using spanner
wrench, install lock washer and shaft nut. Tighten shaft nut to 10-14
ft. lbs. (14-19 N.m).
3) Using a feeler gauge, measure air gap between clutch plate
and pulley assembly at 3 equally spaced locations. Rotate pulley 180
degrees and measure air gap at 3 locations again. Air gap should be 0.
016-0.027" (0.41-0.69 mm). If air gap is not within specification, add\
or remove shims to obtain correct air gap.
4) Add correct amount of refrigerant oil to compressor and
install compressor. See COMPRESSOR REFRIGERANT OIL CHECKING. Evacuate
and charge A/C system. Perform leak test.
SANDEN MSC90-C SCROLL
CLUTCH ASSEMBLY
Removal
1) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Remove compressor. Drain oil from
compressor, and measure amount drained.
2) Remove pulley assembly. Using Spanner (MB991367) and Pins\
(MB991386), remove shaft nut. Remove clutch plate, snap ring and rotor\
assembly. Remove snap ring and clutch coil. See Fig. 6.
Installation
1) Install clutch coil. Ensure projection on back of clutch
coil is aligned with pin hole in compressor body. Install snap ring so
that tapered surface is facing outward.
2) Install rotor assembly and snap ring. Align match mark of
clutch plate with match mark of compressor shaft spline and install
clutch plate. Using spanner and pins, install shaft nut.
3) Using a feeler gauge, check air gap between clutch plate
and rotor assembly at more than one place. Air gap should be 0.016-0.
024" (0.40-0.60 mm). If air gap is not within specification, add or
remove shims as necessary. Install pulley assembly.
4) Add same amount of refrigerant oil to compressor as was
drained from it. Install A/C compressor. Evacuate and charge A/C
system. Perform leak test.

Fig. 6: Compressor Components (Sanden MSC90-C Scroll)
Courtesy of chrysler corp.
SANDEN SD-7H15 7-CYLINDER
NOTE: On Cherokee, Dakota, Durango, Ram Pickup and Wrangler,
compressor clutch can be serviced in vehicle, without
discharging A/C system.
CLUTCH ASSEMBLY
Removal (Cherokee, Dakota, Durango, Ram Pickup & Wrangler)
1) Disconnect and isolate negative battery cable. Remove
serpentine drive belt. Disconnect clutch coil harness connector.
Without disconnecting refrigerant lines, remove A/C compressor from
mounting bracket. Support compressor in engine compartment.
2) Using spanner wrench, hold clutch plate and remove
compressor shaft nut. See Fig. 1. Using a steering wheel puller,
remove clutch plate, compressor shaft key and shims. Remove external
front housing snap ring.
3) Install jaws of Rotor Puller (C-6141-1) into pulley snap
ring groove. Install Shaft Protector (C-6141-2) over compressor shaft.\
Install puller flange plate on jaws. Install Puller Through-Bolts (C-
6461) through puller flange plate into jaws and hand tighten. Tighten
pulley center bolt clockwise and remove pulley from compressor.
4) Remove clutch coil wire harness retainer from compressor
housing. Remove clutch coil snap ring and clutch coil.

Installation (Cherokee & Wrangler)
1) Install clutch coil and clutch coil snap ring. Install
clutch coil wire harness to compressor housing. Align pulley and
bearing assembly on front compressor housing hub. Using Installer (C-
6871), press pulley and bearing assembly onto compressor housing hub.
Thread installer on compressor shaft and tighten nut until pulley
assembly is seated.
2) Install external front snap ring with beveled side facing
outward. Ensure snap ring is properly seated. Install compressor shaft
key and original shims. Using a plastic mallet and Driver (C-6463),
install clutch plate on compressor shaft. Tighten compressor shaft nut
to 10 ft. lbs. (14 N.m).
3) Using feeler gauge, measure air gap between clutch plate
and pulley assembly in several areas. Air gap should be 0.016-0.031"
(0.41-0.79 mm). If air gap is not within specification, adjust shim
thickness as necessary. If air gap is not consistent around clutch
plate, lightly pry up or tap down on clutch plate to make corrections.
To complete installation, reverse removal procedure.
Installation (Dakota, Durango & Ram Pickup)
1) Install clutch coil and clutch coil snap ring. Install
clutch coil wire harness to compressor housing. Align pulley and
bearing assembly on front compressor housing hub.
2) Install Handle (6464) and Driver (6143) into pulley
assembly bearing cavity. Ensure outer edge of driver rests firmly on
inner race of bearing. Using hammer, install pulley and bearing
assembly. While tapping on handle, guide pulley and bearing assembly
to prevent binding. Ensure pulley assembly bottoms against compressor
housing. Install external snap ring.
3) Install original shim(s) and compressor shaft key. Use a
hammer and Shaft Protector (6141-2) to install clutch plate on
compressor shaft. Ensure clutch plate bottoms out on clutch shims.
Replace compressor shaft nut and tighten compressor shaft nut to 10
ft. lbs. (14 N.m).
4) Measure air gap between clutch plate and pulley assembly
in several areas. Air gap should be 0.016-0.031" (0.41-0.79 mm). If
air gap is not within specification, adjust shim thickness as
necessary. If air gap is not consistent around clutch plate, lightly
pry up or tap down on clutch plate to make corrections. To complete
installation, reverse removal procedure. Ensure A/C system operates
properly.
5) After completing compressor clutch installation, start
engine. Set A/C-heater control to recirculated air mode and high
blower motor speed. Set engine speed to 1500-2000 RPM. Cycle
compressor on for 5 seconds and off for 5 seconds, about 20 times to
break-in clutch.
Removal (Ford "F" Series Super Duty Pickup)
1) Disconnect and isolate negative battery cable. Discharge
A/C system, using approved refrigerant recovery/recycling equipment.
Disconnect clutch coil harness connector and remove compressor. Drain
oil from compressor, and measure amount drained.
2) Using Spanner Wrench (T70P-4067-A), hold clutch plate and\
remove compressor shaft nut. See Fig. 1. If necessary, use a steering
wheel puller to remove clutch plate and shim(s).
3) Using a flat-blade screwdriver, remove pulley assembly
bearing dust cover. Remove compressor shaft key and internal bearing
snap ring. Remove external front housing snap ring.
4) Install jaws of rotor puller into pulley assembly internal
bearing snap ring groove. Install shaft protector over compressor
shaft. Install puller flange plate on jaws. Install 2 puller bolts
through puller flange plate into jaws and hand tighten. Tighten pulley
center bolt clockwise and remove pulley assembly from compressor.

BLOWER MOTOR VIBRATION
Possible causes of blower motor vibration include:
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower wheel or fan out of balance.
* Blower motor faulty.
BLOWER MOTOR NOISE
Possible causes of blower motor noise include:
* Foreign material in blower motor housing.
* Foreign material in A/C-heater housing.
* Improper blower motor mounting.
* Improper blower wheel or fan mounting.
* Blower motor faulty.
VACUUM CONTROL SYSTEM DIAGNOSIS
VACUUM CONTROL ONE-WAY CHECK VALVE
NOTE: Some models use brake booster check valve for vacuum source.
These models do not use another in-line vacuum check valve.
1) In engine compartment, locate Black vacuum hose that runs
from brake booster check valve or intake manifold, through firewall
near heater hoses or expansion valve. This supply vacuum hose goes to
A/C-heater control panel vacuum switch.
2) Within Black vacuum hose, disconnect and remove check
valve near intake manifold or brake booster. Connect vacuum gauge to
an external vacuum pump. Start vacuum pump. Plug end of hose probe on
vacuum gauge. Adjust bleed valve on vacuum gauge to obtain an exact
vacuum reading of 8 in. Hg.
3) Unplug and plug end of hose probe on vacuum gauge several
times to ensure exact vacuum reading. Connect vacuum gauge hose probe
to control panel side of check valve. Vacuum gauge reading should be 8
in. Hg. Replace check valve if vacuum leak exists.
4) Connect vacuum gauge hose probe to engine side of check
valve. Vacuum should flow through check valve. Replace check valve if
operation is not as described.
VACUUM CONTROLS
1) This test checks for proper function of control panel
vacuum circuits. Perform steps 1) through 4) under VACUUM CONTROL ONE-\
WAY CHECK VALVE.
2) Connect vacuum gauge hose probe to Black vacuum hose end
that leads to A/C-heater control panel switch. Position vacuum gauge
so gauge reading can be observed from inside vehicle.
3) Operate A/C-heater controls (sliding lever or push
buttons) in all mode positions (floor, defrost, panel, etc.). Pause
after each selection to allow vacuum actuators or motors to energize
and stabilize. Record vacuum gauge reading at each selection.
4) After each selection, vacuum reading should be 7.5-8 in.
Hg. Maximum vacuum reading drop is .75 in. Hg. If proper vacuum
reading cannot be obtained, vacuum leak exists in selected circuit.
5) To check for vacuum leak(s), disconnect 7-way A/C-heater
control panel vacuum harness connector. See Fig. 1. If necessary,
remove control panel from instrument panel to access A/C-heater
control panel vacuum harness connector, or remove lower instrument


* A /C -H EA TE R S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *

1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
A/C-Heater System Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
Motorist Assurance Program (MAP)
OVERVIEW
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Heating, Ventilation and Air Conditioning
ACCUMULATORS
ACTUATORS (ELECTRICAL)
ACTUATORS (VACUUM)
AIR CONDITIONING FITTINGS
AIR CONDITIONING HOSES
AIR CONDITIONING METAL LINES, HOSES AND FITTING ASSEMBLIES
AIR CONTROL DOORS
AIR DAMS (EXTERNAL)
AIR DISTRIBUTION SYSTEM
BELTS
BLEND DOORS
BLOWER FANS (BLOWER WHEEL OR SQUIRREL CAGE)
BLOWER MOTORS
BLOWER RESISTORS
BLOWER SWITCHES
CABIN AIR FILTERS
CIRCUIT BREAKERS
COMPRESSOR CLUTCH ASSEMBLIES
COMPRESSORS
CONDENSER AIR SEALS
CONDENSER FAN MOTORS
CONDENSERS
CONNECTORS
CONTROL CABLES
CONTROL HEADS (FUNCTION SELECTORS)
CONTROL LINKAGES
CONTROL MODULES
COOLANT
COOLING FAN BLADES
COOLING FAN CLUTCHES
COOLING FAN MOTORS
EVAPORATOR DRAIN TUBES
EVAPORATOR PRESSURE REGULATORS (EPRS)
EVAPORATORS
EXPANSION VALVES
FUNCTION SELECTORS
FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS
FUSIBLE LINKS
GASKETS
HEATER CASES
HEATER CONTROL VALVES
HEATER CORES

are continually republished. In addition to these, standards for Drive
Train and Transmissions have recently been promulgated. Participating
shops utilize these Uniform Inspection & Communication Standards as
part of the inspection process and for communicating their findings to
their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,

Worn so it contacts
bottom of pulley ....... A ............ Require replacement.
(1) - Determine cause of incorrect alignment and require repair.
( 2) - Determine cause of noise and suggest repair.









\









\









\









\









\









\









\


BLEND DOORS
See PLENUMS.
BLOWER FANS (BLOWER WHEEL OR SQUIRREL CAGE)
BLOWER FAN (BLOWER WHEEL OR SQUIRREL CAGE) INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Application incorrect ... B .. Require repair or replacement.
Broken .................. A ............ Require replacement.
Cracked ................. A ............. Require replacement
Distorted ............... A ............ Require replacement.
Fins missing ............ C ............ Require replacement.
Hub separated ........... A ............ Require replacement.
Inoperative ............. A ........ ( 1) Require replacement.
Mounting loose .......... A .. Require repair or replacement.
Noisy ................... 2 ............ Suggest replacement.
Out of balance .......... A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.









\









\









\









\









\









\









\


BLOWER MOTORS
BLOWER MOTOR INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted,
affecting performance .. A ........... ( 1) Require repair or
replacement.
Connector melted, not

from housing. To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system.
Removal & Installation (Durango - Rear Evaporator Core)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Remove
headliner from passenger compartment of vehicle. Remove sun visors and
sun visor arm supports.
2) Remove coat hooks, overhead assist handle and dome light.
If equipped, remove overhead console. Remove air outlet bezel from
rear A/C-heater assembly. Remove rear blower motor switch. Remove
upper liftgate opening trim. Disengage "A", "B", "C", and "D" pillar
trim as necessary to prevent trim panel interference.
3) Move second and third row seats to cargo position. Move
front seats to full recline position. Remove headliner fasteners.
Carefully bow headliner and remove through lift gate opening.
4) Disconnect "B" pillar drain hoses from "Y" fittings.
Disconnect "B" pillar refrigerant lines and plug or cover all openings
in A/C system. Remove lower A/C-heater assembly cover. Remove screws
securing refrigerant tube and retaining strap to right side of upper
housing cover. Remove evaporator core. To install, reverse removal
procedure. Install new "O" rings to A/C fittings. Evacuate and charge
A/C system.
Removal & Installation (Ram Pickup - Front)
1) Remove and disassemble A/C-heater housing. See
A/C-HEATER ASSEMBLY . Separate halves of A/C-heater housing and remove
top half. Remove evaporator or heater core from housing.
2) To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system. Fill cooling
system. On 5.9L diesel engine, engine is equipped with a one-way check
valve. DO NOT run engine while filling cooling system. Fill engine
with engine turned off.
INSTRUMENT PANEL
Removal & Installation (Dakota & Durango)
1) Disconnect negative battery cable. Disable air bag system.
See AIR BAG SYSTEM SAFETY article. Place front wheels in straight-
ahead position. Remove sill trim from both doorways. Remove kick panel
covers from both sides of vehicle. Remove mounting screws for hood
release handle.
2) Remove steering column trim panel and support bracket.
Remove tilt steering column lever (if equipped). Remove upper and
lower shrouds from steering column. Unplug driver's side air bag
module. Loosen multifunction switch wiring harness connector screw and
disconnect from switch. Screw will remain in connector.
3) Disconnect PRNDL cable. Disconnect shift cable from
steering column. Remove steering coupler lock pin. Remove toe plate
retaining screws. Remove steering column mounting bolts and remove
steering column from vehicle.
4) Remove screw from bulkhead wiring harness connector and
disconnect. Disconnect 2 body wiring harness connectors located next
to bulkhead connector. Disconnect 3 wiring harness connectors, from
junction block, located nearest to dash panel. Disconnect brake light
switch connector. Disconnect Rear Wheel Anti-Lock (RWAL) brake module
(if equipped), located near steering column support brackets.
5) Disconnect plastic retainer clip from parking brake
linkage rod, located at back of parking brake release handle. Remove
rod end from parking brake handle. Remove instrument panel center
support bracket. Unplug vacuum harness connector located at left end
of A/C-heater housing. Disconnect Air Bag Control Module (ACM)
connector.