DODGE RAM SRT-10 2006 Service Repair Manual

P0480-FAN CLUTCH
For the Engine circuit diagram (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/ENGINE CON-
TROL MODULE - SCHEMATIC - ELECTRICAL)

For a complete wiring diagramRefer to Section 8W.
When Monitored:
When the ignition is on.
Set Condition:
When the control coil is electrically shorted or open.
Possible Causes
FA N C L U TC H
WIRE HARNESS DAMAGED
OPEN FAN CLUTCH (K160) DRIVER CIRCUIT
(K160) DRIVER CIRCUIT SHORTED TO (K690) RETURN CIRCUIT
(K160) DRIVER CIRCUIT SHORTED TO BATTERY NEGATIVE
INTERMITTENT CONDITION
ECM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.FA N C L U T C H
Disconnect the fan clutch harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance between the fan clutch (K160) driver circuit and
the fan speed (K690) sensor return circuit on the fan clutch assembly.
Is the resistance less than 10 Ohms?
Ye s>>
Replace the fan clutch.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
No>>
Go To 2

2.FA N C L U T C H
Disconnect the Fan Clutch harness connectors.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance between the fan clutch (K160) driver circuit and
the fan clutch (F504) battery supply circuit on the fan clutch assembly.
Istheresistancelessthan6Ohmsorgreaterthan10Ohms?
Ye s>>
Replace the fan clutch.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
No>>
Go To 3
3.OPEN FAN CLUTCH (K160) DRIVER CIRCUIT
Disconnect the ECM harness connectors.
Check connectors - Clean/repair as necessary.
Measure the resistance of the fan clutch (K160) driver circuit between
the ECM harness connector and the fan clutch harness connector.
Is the resistance less than 10 Ohms?
Ye s>>
Go To 4
No>>
Repair the open fan clutch (K160) river circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

4.(K160) DRIVER CIRCUIT SHORTED TO (K690) RETURN CIRCUIT
Measure the resistance between the fan clutch (K160) driver circuit and
the fan speed sensor (K690) return circuit at the sensor harness con-
nector.
Is the resistance greater than 100K Ohms?
Ye s>>
Go To 5
No>>
Repair the (K160) Driver circuit shorted to (K690) Return
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
5.(K160) DRIVER CIRCUIT SHORTED TO BATTERY NEGATIVE
Measure the resistance between the fan clutch (K160) driver circuit and
the battery negative.
Is the resistance greater than 100k Ohms?
Ye s>>
Go To 6
No>>
Repair the (K160) Driver circuit shorted to battery negative.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

6.ECM
Reconnect the ECM harness connectors.
Measure the resistance of the fan clutch (K160) driver circuit between
the fan clutch connector and battery negative.
Is the resistance greater than 100k Ohms?
Ye s>>
Refer to the INTERMITTENT CONDITION Symptom (Diag-
nostic Procedure). (Refer to 9 - ENGINE - DIAGNOSIS
AND TESTING)
No>>
replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

P0483-FAN SPEED
For a complete wiring diagramRefer to Section 8W.

When Monitored:
While the engine is running.
Set Condition:
The actual fan speed is less than 50 RPM or more than 6000 RPM.
Possible Causes
OTHER DTC’S
(K161) SIGNAL CIRCUIT SHORT TO (K668) 5-VOLT SUPPLY CIRCUIT
(K161) SIGNAL CIRCUIT OPEN FROM ECM TO FAN CLUTCH ASSEMBLY
(K668) 5-VOLT SUPPLY CKT OPEN FROM ECM HARNESS CONNECTOR TO FAN CLUTCH HARNESS
CONNECTOR
INTERMITTENT CONDITION
(K161) SIGNAL CIRCUIT SHORTED TO (690) RETURN IN THE HARNESS
(K161) SIGNAL CIRCUIT SHORTED TO VOLTAGE
(K161) SIGNAL CIRCUIT IN ECM SHORTED TO GROUND INSIDE ECM
(K161) SIGNAL CIRCUIT SHORTED TO VOLTAGE IN THE ECM
(K668) 5-VOLT SUPPLY CIRCUIT IN ECM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.OTHER DTC’S PRESENT
With the scan tool, read DTCs.
Is DTC P0480 present?
Ye s>>
Repair other DTC’s first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 2
2.FA N C L U T C H S H O R T E D
Disconnect the wiring harness from the fan clutch assembly.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance between the signal circuit in the fan clutch assembly and the return circuit in the fan clutch
assembly.
Is the resistance less than 10 Ohms?
Ye s>>
Replace the fan clutch assembly.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 3

3.FAN CLUTCH ASSEMBLEY SHORTED TO GROUND
Measure the resistance between the signal circuit in the fan clutch assembly and battery negative.
Is the resistance less than 10 Ohms?
Ye s>>
Replace the fan clutch assembly.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No>>
Go To 4
4.(K161) SIGNAL CIRCUIT SHORT TO (K668) 5-VOLT SUPPLY CIRCUIT
Disconnect the Fan clutch connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance between the (K161) signal circuit in the fan
clutch assembly and the battery (K668) 5-volt supply circuit in the fan
clutch assembly.
Is the resistance less than 10 Ohms?
Ye s>>
Replace the Fan clutch assembly.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
No>>
Go To 5

5.(K161) SIGNAL CIRCUIT OPEN FROM ECM TO FAN CLUTCH ASSEMBLY
Disconnect the ECM harness connectors.
Check connectors - Clean/repair as necessary.
Measure the resistance of the (K161) signal circuit between the ECM
harness connector and the fan clutch assembly harness connector.
Is the resistance less than 10 Ohms?
Ye s>>
Go To 6
No>>
Repair the open (K161) circuit from the ECM harness con-
nector to the Fan clutch harness connector.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
6.(K668) 5-VOLT SUPPLY CIRCUIT OPEN FROM ECM HARNESS CONNECTOR TO FAN CLUTCHHARNESS
Measure the resistance of the (K668) 5-volt supply circuit between the
ECM harness connector and the fan clutch assembly harness connec-
tor.
Is the resistance less than 10 Ohms?
Ye s>>
Go To 7
No>>
Repair the open (K668) circuit from ECM harness connector
to Fan clutch connector.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)

7.(K161) SIGNAL CIRCUIT SHORTED TO RETURN IN THE HARNESS
Measure the resistance between the (K161) signal circuit in the fan
clutch assembly harness connector and the return circuit in the fan
clutch assembly harness connector.
Is the resistance less than 10 Ohms?
Ye s>>
Repair the shorted (K161) circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
No>>
Go To 8
8.(K161) SIGNAL CIRCUIT SHORTED TO VOLTAGE
Measure the voltage between the (K161) signal circuit in the fan clutch
assembly harness connector and battery negative.
Is the voltage greater than 1 volt?
Ye s>>
Repair the (K161) signal circuit shorted to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
No>>
Go To 9