light FIAT 500L 2019 Owner handbook (in English)

116)The space-saver wheel (for
versions/markets where provided) is
specific to your car, do not use it on other
models, or use the space-saver wheel
of other models on your car. The
space-saver wheel must only be used in
the event of an emergency. Never use it for
more than strictly necessary and never
exceed 80 km/h. "Warning! For temporary
use only! 80km/h max! Replace with
standard wheel as soon as possible. Never
remove or cover the sticker on the
space-saver wheel. Never apply a wheel
cap on a space-saver wheel. The vehicle's
driving characteristics will be modified
with the space-saver wheel fitted. Avoid
violent acceleration and braking, abrupt
steering and fast cornering.
117)Alert other drivers that the car is
stationary in compliance with local
regulations: hazard warning lights, warning
triangle, etc. Any passengers on board
should leave the car, especially if it is
heavily laden. Passengers should stay
away from on-coming traffic while the
wheel is being changed. If you are on a
slope or uneven surface, place the wedge
provided under the wheel (see the
instructions on the next pages).118)The vehicle's driving characteristics
will be modified with the space-saver wheel
fitted. Avoid violent acceleration and
braking, abrupt steering and fast cornering.
The overall duration of the space-saver
wheel is of about 3000 km, after which the
relevant tyre must be replaced with another
one of the same type. Never install a
standard tyre on a rim that is designed for
use with a space-saver wheel. Have the
wheel repaired and refitted as soon as
possible. Using two or more space-saver
wheels at the same time is forbidden.
Do not grease the threads of the stud bolts
before fitting them: they might slip out.
119)The jack is a tool developed and
designed only for changing a wheel, if a
tyre gets punctured or damaged, on the
vehicle with which it is supplied or on other
vehicles of the same model. Any other
use, e.g. to jack up other vehicle models or
different things, is strictly prohibited. Never
use it to carry out maintenance or repairs
under the vehicle or to change summer/
winter wheels and vice versa: we advise
you to contact a Fiat Dealership. Never go
under the raised vehicle: use it only in
the positions indicated. Do not use the jack
for loads higher than the one shown on
its label. Never start the engine with vehicle
raised. If the vehicle is raised more than
necessary, everything can become more
unstable, with the risk of the vehicle
dropping violently. Thus, lift the car only as
needed in order to access the space-saver
spare wheel.120)The space-saver wheel cannot be
fitted with snow chains. If a front (drive) tyre
is punctured and chains are needed, use
a standard wheel from the rear axle and
install the space-saver wheel on the rear
axle. In this way, with two normal drive
wheels at the front axle, it is possible to use
snow chains.
121)When turning the jack handle make
sure that it can turn freely without scraping
your hand against the ground. The moving
components of the jack ("worm screw"
and joints) can also cause injuries: do not
touch them. If you come into contact
with lubricating grease, clean yourself
thoroughly.
122)Incorrectly fitting the wheel cap may
cause it to fall off when the car is in motion.
Never tamper with the inflation valve.
Never introduce tools of any kind between
rim and tyre. Check tyre and space-saver
wheel pressures regularly, complying
with the values given in the "Technical
specifications" chapter.
123)At the end of the operation of
raising/locking the space-saver wheel
device, the spanner must be extracted,
taking care NOT to turn it in the wrong
direction to facilitate the extraction of the
spanner itself, so as to prevent the
attachment device from being released and
the lack of safe restraint.
WARNING
51)Contact a Fiat Dealership as soon as
possible to have the correct tightening
of the wheel stud bolts checked.
127

CARTRIDGE
REPLACEMENT
Proceed as follows:
only use original cartridges, which
can be purchased from the Fiat
Dealership;
to remove the cartridge, press the
release button and lift it (see description
above).
WARNING
124)WARNING Do not exceed 80 km/h.
Avoid sudden acceleration or braking. The
kit provides a temporary repair, therefore
the tyre must be examined and repaired by
a specialist as soon as possible. Before
using the kit, ensure that the tyre is not
excessively damaged and that the rim is in
good condition, otherwise do not use it
and call roadside assistance. Do not
remove foreign bodies from the tyre. Do
not let the compressor turned on for more
than 20 consecutive minutes - overheating
hazard.
125)The information required by the
applicable regulation is indicated on the
Fix&Go kit package label. Carefully read the
label on the cartridge before use, avoid
improper use. The kit should be used by
adults and cannot be used by children.
WARNING
52)The sealant is effective with external
temperatures of between -40°C and
+55°C. The sealant has an expiry date. It is
possible to repair tyres which have been
damaged on tread up to a diameter of
6 mm. Show the cartridge and the label to
the personnel charged with handling the
tyre treated with the tyre repair kit.
WARNING
2)Dispose of the bottle and the sealant
liquid properly. Have them disposed of in
compliance with national and local
regulations.
CHANGING A BULB
126) 127) 128) 129)53) 54)
GENERAL
INSTRUCTIONS
Before replacing a bulb check the
contacts for oxidation.
Burnt bulbs must be replaced by
others of the same type and power.
After replacing a headlight bulb,
always check that alignment of the light
beam is correct.
When a light is not working, check
that the corresponding fuse is intact
before changing a bulb. For the location
of fuses, refer to the paragraph “If a
fuse blows” in this section;
130
IN AN EMERGENCY

IMPORTANT When the weather is cold
or damp or after heavy rain or washing,
the surface of headlights or rear lights
may steam up and/or form drops of
condensation on the inside. This is
a natural phenomenon due to the
difference in temperature and humidity
between the inside and the outside
of the glass which does not indicate a
fault and does not compromise the
normal operation of lighting devices.
The mist disappears quickly when the
lights are turned on, starting from
the centre of the diffuser, extending
progressively towards the edges.
131

BULB TYPES
UseType Power
Dipped/main beam headlights H7 55W
Daytime running lights (DRL) LED + bulb W21W 21W
Front side lights LED –
Rear side lights/Brake lights P21/5W 21W/5W
Front direction indicators PY21W 21W
Side direction indicators WY5W 5W
Rear direction indicators P21W 21W
Third brake light LED –
Fog lights H11 55W
Reverse gear W16W 16W
Rear fog light W16W 16W
Number plate C5W 5W
Front ceiling light C5W 5W
Front roof lights (sun visors) C5W 5W
Boot ceiling light W5W 5W
Glove compartment light C5W 5W
Rear ceiling lights C5W 5W
132
IN AN EMERGENCY

FRONT UPPER LIGHT
CLUSTER
This contains the bulbs for the direction
indicators and dipped headlights.
The bulbs are arranged as follows fig.
125:
A: direction indicators
B: dipped beam headlights
DIRECTION INDICATORS
To replace the bulb, proceed as follows:
remove cover A fig. 125;
turn bulb holder B fig. 126
anticlockwise, extract bulb C and
replace it;
refit the new bulb on the bulb holder,
making sure it is correctly locked;
refit the bulb holder in its housing
and turn it clockwise, until the locking
click is heard;
then refit the cover A fig. 125.DIPPED BEAM
HEADLIGHTS
To replace the bulb, proceed as follows:
remove cover B fig. 125;
remove the connector and bulb
holder C fig. 127 unit, releasing it
outwards;
remove bulb D from connector E
and replace it;
refit the new bulb on the connector,
making sure it is correctly locked;
refit the connector and bulb holder C
unit in its housing;
then refit the cover B fig. 125.
FRONT LOWER LIGHT
CLUSTER
This contains the bulbs for the main
beams and side lights/daytime running
lights (DRL).
The bulbs are arranged as follows fig.
128:
C: main beam headlights
D: side lights/daytime running lights
(DRL)
MAIN BEAM HEADLIGHTS
To replace the bulb, proceed as
follows:
steer the wheel completely inwards;
undo the screws A fig. 129 and
remove the flap B;
remove cover C fig. 128;
125F0Y0021C
126F0Y0022C
127F0Y0023C
128F0Y0499C
133

remove the connector and bulb
holder D unit, releasing it outwards;
remove the bulb E from connector F
and replace it;
refit the new bulb on the connector,
making sure it is correctly locked;
refit the connector and bulb holder D
unit in its housing;
finally refit cover C.SIDE LIGHTS/DAYTIME
RUNNING LIGHTS (DRL)
Side lights/daytime running lights
(DRL)
(versions with LED lights)
For light replacement, contact a Fiat
Dealership.
Daytime running lights (DRL)
(versions with incandescent bulb)
To replace the bulb, proceed as follows:
steer the wheel completely inwards;
undo the screws A fig. 129 and
remove the flap B;
remove cover D fig. 128;
turn bulb holder E fig. 131
anticlockwise, extract bulb F from
connector G and replace it;
refit the new bulb on the connector,
making sure it is correctly locked;
refit the bulb holder unit E in its
housing and turn it clockwise, until the
locking click is heard;
finally refit cover D.
SIDE DIRECTION
INDICATORS
To replace the bulb, proceed as follows:
adjust the lens A fig. 132 to
compress in the internal catch B fig.
133, then pull the cluster outwards;
turn the bulb holder C anticlockwise,
extract bulb D and replace it;
refit the bulb holder C in the lens A
fig. 132and turn it clockwise;
refit the cluster making sure that the
internal catch B fig. 133 clips into
position.
129F0Y0145C
130F0Y0025C
131F0Y0026C
132F0Y0147C
134
IN AN EMERGENCY

FOG LIGHTS
(for versions/markets, where provided)
To replace the bulb, proceed as follows:
steer the wheel completely inwards;
undo the screws A fig. 134 and
remove the flap B;
release the clip C fig. 135 and
disconnect the electrical connector D;
turn and remove the bulb holder E;
release the bulb and replace it;
refit the new lamp and carry out the
procedure described previously in
reverse.
REAR LIGHT CLUSTERS
These contain the bulbs for the side
lights, brake lights and direction
indicators.
To replace the bulbs, proceed as
follows:
take the Allen key A fig. 136
provided;
operate tab B fig. 137 and remove
protective cover C (located in the side
area of the luggage compartment);
use Allen key A to unscrew fixing
devices D fig. 138 of the rear light
cluster;
extract the light cluster by removing
it with both hands in the direction
indicated by the arrows fig. 139;
133F0Y0171C
134F0Y0148C
135F0Y0033C136F0Y0149C
137F0Y0150C
138F0Y0258C
135

disconnect the electrical connector,
undo the fixing screws E fig. 140 and
remove the bulb holder assembly;
then replace the bulb concernedfig.
141: F = direction indicators, G =
side/brake lights.
FIXED REAR LIGHT
CLUSTERS
These contain the rear fog light bulbs
(left side) and reversing light bulbs (right
side).
IMPORTANT
Take
particular
care
when

replacing
the
rear
fog
light
bulb:
RISK

OF
BURNS
if
the
exhaust
pipe
is
hot
500Lversions
To
replace
the
bulb,
proceed
as
follows:
GSPN
UIF
VOEFSOFBUI
PG
UIF
SFBS

CVNQFS

SFMFBTF
UIF
UBCT
"
GJH



VOTDSFX
UIF
GJYJOH
TDSFX
#
BOE
SFNPWF

UIF
GMBQ
XIFSF
QSPWJEFE

disconnect
the
electrical
connector

C,
rotate
the
bulb/bulb
holder
unit
D

anticlockwise
fig.
143
and
remove
the

unit;
release
the
bulb
and

replace
it;
reinsert
the
bulb/bulb
holder
unit
D

by
turning
it
clockwise;
reconnect
the
electric
connector
C;
refit
the
flap
and
check
that
it
is

correctly
locked;
tighten the fixing screw B.500L WAGON versions
To replace the bulb, proceed as follows:
open the luggage compartment,
remove the trim frame, undo the four
fixing screws A fig. 144 and remove
light cluster B;
disconnect the electrical connector
and rotate bulb holder C anticlockwise
fig. 145;
remove bulb D from the bulb holder
and replace it;
139F0Y0151C
140F0Y0027C
141F0Y0028C142F0Y0634C
143F0Y0635C
136
IN AN EMERGENCY

refit the new bulb on the bulb holder,
making sure it is correctly locked;
refit bulb holder C in the lens turning
it clockwise and reconnect the electrical
connector;
refit the light cluster B fig. 144
correctly by tightening the four fixing
screws A, then close the luggage
compartment.THIRD BRAKE LIGHTS
These are LEDs. They are located in the
tailgate. For replacement, contact a
Fiat Dealership.
NUMBER PLATE LIGHTS
To replace the bulbs, proceed as
follows:
remove lens A fig. 146;
replace the bulb B fig. 147 releasing
it from the side contacts;
insert the new bulb and make sure
that it is correctly clamped between the
contact and refit the lens A fig. 146.
WARNING
126)Before replacing the bulb, wait for the
exhaust ducts to cool down: DANGER
OF SCALDING!
127)Modifications or repairs to the electric
system that are not carried out properly
or do not take the system technical
specifications into account can cause
malfunctions leading to the risk of fire.
128)Halogen bulbs contain pressurised
gas, in the case of breakage they may
burst causing glass fragments to be
projected outwards.
129)Only replace the light bulbs when the
engine is off and in a position that does
not interfere with traffic and lets you safely
replace them (see the description in the
“Replacement” paragraph). Also ensure
that the engine is cold, to prevent the risk
of burns.
144F0Y0032C
145F0Y0029C
146F0Y0030C
147F0Y0031C
137

WARNING
53)Halogen bulbs must be handled
holding the metallic part only. Touching the
transparent part of the bulb with your
fingers may reduce the intensity of the
emitted light and even reduce the lifespan
of the bulb. In the event of accidental
contact, wipe the bulb with a cloth
moistened with alcohol and let the bulb
dry.
54)Where possible, it is advisable to have
bulbs changed at a Fiat Dealership. The
correct operation and direction of the
external lights are absolutely essential for
the safety of the car and of compliance
with the law.
REPLACING FUSES
130) 131) 132) 133) 134) 135)55)
FUSE LOCATION
Fuses are grouped together in three
fuseboxes located in the engine
compartment, under the dashboard
and inside the boot.
ENGINE COMPARTMENT
CONTROL UNIT
To access the fuses unscrew the two
screws A fig. 148 and remove the cover
B in the direction shown by the arrow.
IMPORTANT Before removing cover
Bfig. 148 press and turn the two
bayonet screws A slowly anticlockwise
(using the flat tip screwdriver provided)
until unlocking them. This is shown
by the screw heads lifting.After replacing the fuse, make sure you
close cover B on the junction unit.
The fuseboxfig. 149 is located by the
side of the battery.
148F0Y0071C
149F0Y0072C
138
IN AN EMERGENCY