brake FIAT 500X 2014 2.G Owner's Manual

•Whether or not the driver and passenger safety belts
were buckled/fastened;
• How far (if at all) the driver was depressing the
accelerator and/or brake pedal; and,
• How fast the vehicle was traveling.
• These data can help provide a better understanding
of the circumstances in which crashes and injuries
occur.
NOTE: EDR data are recorded by your vehicle only if a
non-trivial crash situation occurs; no data are recorded
by the EDR under normal driving conditions and no
personal data (e.g., name, gender, age, and crash loca-
tion) are recorded. However, other parties, such as law
enforcement, could combine the EDR data with the type
of personally identifying data routinely acquired dur-
ing a crash investigation.
To read data recorded by an EDR, special equipment is
required, and access to the vehicle or the EDR is needed.
In addition to the vehicle manufacturer, other parties,
such as law enforcement, that have the special equip-
ment, can read the information if they have access to the
vehicle or the EDR.Child Restraints
Everyone in your vehicle needs to be buckled up at all
times, including babies and children. Every state in the
United States, and every Canadian province, requires
that small children ride in proper restraint systems. This
is the law, and you can be prosecuted for ignoring it.
Children 12 years or younger should ride properly
buckled up in a rear seat, if available. According to
crash statistics, children are safer when properly re-
strained in the rear seats rather than in the front.
WARNING!
In a collision, an unrestrained child can become a
projectile inside the vehicle. The force required to
hold even an infant on your lap could become so
great that you could not hold the child, no matter
how strong you are. The child and others could be
badly injured. Any child riding in your vehicle
should be in a proper restraint for the child’s size.
188 SAFETY

WARNING!
An improperly attached, damaged, folded, or
stacked floor mat, or damaged floor mat fasteners
may cause your floor mat to interfere with the
accelerator, brake, or clutch pedals and cause a loss
of vehicle control. To prevent SERIOUS INJURY or
DEATH:
•ALWAYS securely attach
your floor mat using
the floor mat fasteners. DO NOT install your
floor mat upside down or turn your floor mat
over. Lightly pull to confirm mat is secured
using the floor mat fasteners on a regular basis.
• ALWAYS REMOVE THE EXISTING FLOOR
MAT FROM THE VEHICLE
before installing
any other floor mat. NEVER install or stack an
additional floor mat on top of an existing floor
mat.
• ONLY install floor mats designed to fit your
vehicle. NEVER install a floor mat that cannot be
properly attached and secured to your vehicle. If a
floor mat needs to be replaced, only use a FCA
approved floor mat for the specific make, model,
and year of your vehicle.
(Continued)
WARNING! (Continued)
•ONLY use the driver ’s side floor mat on the
driver ’s side floor area. To check for interference,
with the vehicle properly parked with the engine
off, fully depress the accelerator, the brake, and
the clutch pedal (if present) to check for interfer-
ence. If your floor mat interferes with the opera-
tion of any pedal, or is not secure to the floor,
remove the floor mat from the vehicle and place
the floor mat in your trunk.
• ONLY use the passenger ’s side floor mat on the
passenger ’s side floor area.
• ALWAYS make sure objects cannot fall or slide
into the driver ’s side floor area when the vehicle
is moving. Objects can become trapped under
accelerator, brake, or clutch pedals and could
cause a loss of vehicle control.
• NEVER place any objects under the floor mat
(e.g., towels, keys, etc.). These objects could
change the position of the floor mat and may
cause interference with the accelerator, brake, or
clutch pedals.
(Continued)
208 SAFETY

WARNING!(Continued)
•If the vehicle carpet has been removed and re-
installed, always properly attach carpet to the
floor and check the floor mat fasteners are secure
to the vehicle carpet. Fully depress each pedal to
check for interference with the accelerator, brake,
or clutch pedals then re-install the floor mats.
• It is recommended to only use mild soap and
water to clean your floor mats. After cleaning,
always check your floor mat has been properly
installed and is secured to your vehicle using the
floor mat fasteners by lightly pulling mat.
Periodic Safety Checks You Should Make
Outside The Vehicle
Tires
Examine tires for excessive tread wear and uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread or sidewall. Inspect the tread for
cuts and cracks. Inspect sidewalls for cuts, cracks, and
bulges. Check the wheel nuts for tightness. Check the
tires (including spare) for proper cold inflation pres-
sure.
Lights
Have someone observe the operation of brake lights
and exterior lights while you work the controls. Check
turn signal and high beam indicator lights on the
instrument panel.
Door Latches
Check for proper closing, latching, and locking.
Fluid Leaks
Check area under vehicle after overnight parking for
fuel, engine coolant, oil, or other fluid leaks. Also, if
gasoline fumes are detected, or if fuel or brake fluid
leaks are suspected, the cause should be located and
corrected immediately.
6
SAFETY 209

STARTING AND OPERATING
CONTENTS
STARTING THE ENGINE ...............214
▫ Tip Start Feature .....................215
▫ If Engine Fails To Start ................215
▫ Cold Weather Operation ...............216
▫ Extended Park Starting .................216
▫ After Starting — Warming Up The Engine . . .217
▫ Stopping The Engine ..................217
▫ Turbocharger “Cool Down” — If Equipped . .217
 ENGINE BREAK-IN RECOMMENDATIONS . .217
 ELECTRIC PARK BRAKE (EPB) ...........218
▫ Auto Park Brake .....................221
▫ SafeHold ......................... .222
▫ Brake Service Mode ...................222
 MANUAL TRANSMISSION ..............223 ▫
Shifting ........................... .224
▫ Downshifting ...................... .225
 AUTOMATIC TRANSMISSION ...........226
▫ Gear Selector ....................... .228
▫ Gear Ranges ....................... .229
▫ Transmission Limp Home Mode ..........234
▫ Ignition Park Interlock .................235
▫ Brake/Transmission Shift Interlock System . . .235
 SPEED CONTROL — IF EQUIPPED ........235
▫ Activation ......................... .236
▫ Setting A Desired Speed ................236
▫ Deactivation ....................... .236
▫ Resume Speed ...................... .236
▫ Varying The Speed ...................236
7

▫Accelerating For Passing ...............237
 ALL WHEEL DRIVE (AWD) — IF EQUIPPED .238
 DYNAMIC SELECTOR — IF EQUIPPED .....238
▫ Warning Messages ....................239
 BRAKE CONTROL — IF EQUIPPED ........239
▫ Brake Control ...................... .239
▫ Turning Brake Control On Or Off .........241
▫ Changing Brake Control Sensitivity ........241
▫ Brake Control Limited Warning ...........242
▫ Service Brake Control Warning ...........242
▫ Precautions While Driving With Brake
Control ........................... .243
▫ General Information ..................246
 PARKSENSE REAR PARK ASSIST — IF
EQUIPPED ......................... .246
▫ ParkSense Sensors ....................247
▫ Enabling And Disabling ParkSense ........248
▫ Service The Rear Park Assist System .......249▫
ParkSense System Usage Precautions .......249
 LANESENSE — IF EQUIPPED ............251
▫ LaneSense Operation ..................251
▫ Turning LaneSense On Or Off ............252
▫ LaneSense Warning Message .............252
▫ Changing LaneSense Status .............254
 PARKVIEW REAR BACK UP CAMERA — IF
EQUIPPED ......................... .255
 TIRE PRESSURE MONITORING SYSTEM
(TPMS) ............................ .257
▫ Base System ....................... .259
▫ General

Information ...................261
 FUEL REQUIREMENTS .................261
▫ 1.4L Turbo Engine ....................261
▫ 2.4L Engine ........................ .262
▫ Reformulated Gasoline ................262
▫ Gasoline/Oxygenate Blends .............262
▫ E-85 Usage In Non-Flex Fuel Vehicles ......263
212 STARTING AND OPERATING

STARTING THE ENGINE
Before starting your vehicle, adjust your seat, adjust the
inside and outside mirrors, fasten your seat belt, and if
present, instruct all other occupants to buckle their seat
belts.
WARNING!
•Never leave children alone in a vehicle, or with
access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or
others could be seriously or fatally injured. Chil-
dren should be warned not to touch the parking
brake, brake pedal or the gear selector.
• Do not leave the key fob in or near the vehicle (or
in a location accessible to children), and do not
leave the ignition in the ON or RUN mode. A
child could operate power windows, other con-
trols, or move the vehicle.
Start the engine with the gear selector in the NEUTRAL
or PARK position. Apply the brake before shifting to
any driving range. Manual Transmission
Proceed as follows:
1. Set the Electric Park Brake (EPB) and put the gear
selector in the NEUTRAL position.
2. Press the clutch pedal to the floor, without pressing the accelerator.
3. Cycle the ignition to the START mode and release it as soon as the engine is started.
4. If the engine does not start, place the ignition in the OFF mode and wait 10-15 seconds before attempting
to restart the engine.
Automatic Transmission
Proceed as follows:
1. Set the Electric Park Brake (EPB) and put the gear selector in the PARK or NEUTRAL position.
2. Press on the brake pedal, without pressing the accel- erator.
3. Cycle the ignition to the START mode and release it as soon as the engine is started.
214 STARTING AND OPERATING

While cruising, brief full-throttle acceleration within the
limits of local traffic laws contributes to a good break-in.
Wide-open throttle acceleration in low gear can be
detrimental and should be avoided.
The engine oil installed in the engine at the factory is a
high-quality energy conserving type lubricant. Oil
changes should be consistent with anticipated climate
conditions under which vehicle operations will occur.
For the recommended viscosity and quality grades,
refer to “Dealer Service” in “Servicing And Mainte-
nance”.
CAUTION!
Never use Non-Detergent Oil or Straight Mineral
Oil in the engine or damage may result.
NOTE: A new engine may consume some oil during its
first few thousand miles (kilometers) of operation. This
should be considered a normal part of the break-in and
not interpreted as a problem.
ELECTRIC PARK BRAKE (EPB)
Your vehicle is equipped with an Electric Park Brake
System (EPB) that offers simple operation, and some
additional features that make the parking brake more
convenient and useful.
The parking brake is primarily intended to prevent the
vehicle from rolling while parked. Before leaving the
vehicle, make sure that the parking brake is applied.
Also, be certain to leave the transmission in PARK.
The EPB switch is located in the center console.
You can engage the EPB in two ways;
• Manually, by pulling up on the park brake switch
momentarily to apply.
• Automatically, by enabling the Auto Park Brake
feature in the customer programmable features sec-
tion of the Uconnect Settings.
218 STARTING AND OPERATING

To apply the EPB manually, pull up on the switch
momentarily. You may hear a slight whirring sound
from the back of the vehicle while the EPB engages.
Once the parking brake is fully engaged, the BRAKE
warning lamp in the instrument cluster and an indica-
tor on the switch will illuminate. If your foot is on the
brake pedal while you apply the EPB, you may notice a
small amount of brake pedal movement. The EPB can
be applied even when the ignition switch is in the OFF
mode but the BRAKE warning lamp will not illuminate,
however, it can only be released when the ignition is in
the RUN mode.NOTE:
The EPB fault lamp will illuminate if the EPB
switch is held for longer than 20 seconds in either the
released or applied position. The light will extinguish
upon releasing the switch.
If the Auto Park Brake feature is enabled, the EPB will
automatically engage whenever the transmission is
placed into PARK, or with a manual transmission, when
the ignition switch is in the STOP/OFF position. If your
foot is on the brake pedal, you may notice a small
amount of brake pedal movement while the EPB is
engaging.
The EPB will be automatically released if the driver ’s
seat belt is buckled and driver’s intention to start (in
forward or reverse direction) is recognized by the
system
To release the EPB manually, the ignition must be in the
RUN mode. Put your foot on the brake pedal, then push
the EPB switch down momentarily. You may hear a
slight whirring sound from the back of the vehicle while
the parking brake disengages. You may also notice a
small amount of movement in the brake pedal. Once the
EPB is fully disengaged, the BRAKE warning lamp in
the instrument cluster and the LED indicator on the
switch will extinguish.
Electric Park Brake Switch7
STARTING AND OPERATING 219

NOTE:
•When parking on a hill, it is important to turn the
front wheels toward the curb on a downhill grade
and away from the curb on an uphill grade. Apply
the EPB before placing the gear selector in PARK,
otherwise the load on the transmission locking
mechanism may make it difficult to move the gear
selector out of PARK. The EPB should always be
applied whenever the driver is not in the vehicle.
• If the clutch pedal is released at the same time the gas
pedal is pressed, the EPB will be automatically
released (manual transmissions only).
WARNING!
• When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children
to be in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Children should be
warned not to touch the parking brake, brake
pedal or the transmission gear selector.
(Continued)
WARNING! (Continued)
•Do not leave the key fob in or near the vehicle (or
in a location accessible to children), and do not
leave the ignition in the ON or RUN mode. A
child could operate power windows, other con-
trols, or move the vehicle.
• Be sure the parking brake is fully disengaged
before driving; failure to do so can lead to brake
failure and a collision.
• Always fully apply the parking brake when leav-
ing your vehicle, or it may roll and cause damage
or injury. Also be certain to leave the transmission
in PARK. Failure to do so may allow the vehicle to
roll and cause damage or injury.
CAUTION!
If the Brake System Warning Light remains on with
the parking brake released, a brake system mal-
function is indicated. Have the brake system ser-
viced by an authorized dealer immediately.
If exceptional circumstances should make it necessary
to engage the EPB while the vehicle is in motion,
maintain upward pressure on the EPB switch for as
220 STARTING AND OPERATING

long as engagement is desired. The brake warning lamp
could illuminate in case of the hydraulic system is not
available. The rear stop lamps will also be illuminated
automatically while the vehicle remains in motion.
To disengage the EPB while the vehicle is in motion,
release the switch. If the vehicle is brought to a com-
plete stop using the EPB, when the vehicle reaches
approximately 1.9 mph (3 km/h) the EPB will remain
engaged.
WARNING!
Driving the vehicle with the parking brake en-
gaged, or repeated use of the parking brake to slow
the vehicle may cause serious damage to the brake
system. Be sure the parking brake is fully disen-
gaged before driving; failure to do so can lead to
brake failure and a collision.
In the unlikely event of a malfunction of the EPB
system, a yellow EPB fault lamp will illuminate. This
may be accompanied by the Brake warning lamp flash-
ing. In this status some EPB functionalities may be deactivated. In this event, urgent service of the EPB
system is required. Do not rely on the EPB to hold the
vehicle stationary.
Auto Park Brake
The EPB can be programmed to be applied automati-
cally whenever the vehicle speed is below 1.9 mph
(3 km/h) and the automatic transmission is placed in
PARK, or with a manual transmission, whenever the
ignition is in the OFF mode. Auto Park Brake is enabled
and disabled by customer selection through the Cus-
tomer Programmable Features section of the Uconnect
Settings.
Any single Auto Park Brake application can be by-
passed by pushing the EPB switch to the release posi-
tion while the transmission is placed in PARK (auto-
matic transmission) and the ignition is in the RUN
mode. In some cases, in case of Automatic or Dual
clutch transmission, when the ignition is in the OFF
mode EPB can automatically apply even if it has been
previously disabled
7
STARTING AND OPERATING 221