reset FORD ASPIRE 1996 1.G Owners Manual

50
*
[ST06875(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST06880(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST06885(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST06890(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
*
[ST08350(ALL)10/95]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs high. These faster
engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It
should, however, slow down after a short time.
If it does not, have the idle speed checked.
*
[ST08365(ALL)07/95]
If the engine idle speed does not slow down
automatically, do not allow your vehicle to idle
for more than 10 minutes. Have the vehicle
checked.
*
[ST08375(ALL)05/95]
RWARNING
Extended idling at high engine speeds can
produce very high temperatures in the
engine and exhaust system, creating the
risk of fire or other damage.
*
[ST08500(ALL)05/95]
RWARNING
Do not park, idle, or drive your vehicle in
dry grass or other dry ground cover. The
emission system heats up the engine
compartment and exhaust system, which
can start a fire.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996

52
*
[ST09470(ALL)03/95]
Once the shut-off switch is triggered, you must
reset the switch by hand before you can start
your vehicle.
[ST09480(ALL)02/95]
The reset switch on your vehicle is located in a
small compartment on the left side of the
luggage compartment.
[ST09490(ALL)02/95]
half page art:0032161-C
The location of the fuel pump shut-off switch (U.S. vehicle
shown Ð Canadian vehicles similar)
*
[ST09500(ALL)05/95]
RWARNING
If you see or smell fuel, do not reset the
switch or try to start your vehicle. Have
all the passengers get out of the vehicle
and call the local fire department or a
towing service.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996

53
*
[ST09510(ALL)10/95]
If your engine cranks but does not start after a
collision or major jolt:
*
[ST09520(ALL)02/95]
1. Turn the key in the ignition to the LOCK
position.
*
[ST09530(ALL)03/95]
2. Check under the vehicle for leaking fuel.
[ST09540(ALL)02/95]
3. If you do not see or smell fuel, remove the
door covering the fuel pump shut-off switch
compartment by pressing the tab toward the
rear seat. Push down the red reset button on
the fuel pump shut-off switch.
*
[ST09550(ALL)02/95]
4. Attempt to start your vehicle. If the vehicle
starts, let it run a few seconds, then turn the
key to the LOCK position.
*
[ST09560(ALL)03/95]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
*
[ST09600(ALL)09/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
%*
[ST11700(ALL)05/95]
Guarding Against Exhaust Fumes
*
[ST11800(ALL)02/95]
Carbon monoxide, although colorless and
odorless, is present in exhaust fumes. Take
precautions to avoid its dangerous effects.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996

66
*
[LG06700(ALL)05/95]
If, under any circumstances, the pointer moves
above the NORMAL band, the engine coolant is
overheating and continued operation may cause
engine damage.
*
[LG06800(ALL)01/95]
If your engine coolant overheats:
*
[LG06900(ALL)03/95]
1. Pull off the road as soon as safely possible.
*
[LG07000(ALL)01/95]
2. Turn off the engine.
*
[LG07100(ALL)05/95]
3. Let the engine cool.
*
[LG07200(ALL)03/95]
4. Check the coolant level following the
instructions on checking and adding coolant
to your engine. (SeeEngine coolantin the
Index.) If you do not follow these
instructions, you or others could be injured.
*
[LG07300(ALL)05/92]
5. Add as much coolant as your engine needs.
If the engine continues to overheat, have the
coolant system serviced.
*
[LG07500(ALL)01/95]
Speedometer
*
[LG07600(ALL)01/95]
The speedometer tells you how many miles
(kilometers) per hour your vehicle is moving.
*
[LG07700(ALL)01/95]
Odometer
*
[LG07800(ALL)01/95]
The odometer tells you the total number of miles
(kilometers) your vehicle has been driven.
%*
[LG07900(ALL)11/94]
Trip Odometer
[LG07920(ALL)09/93]
The trip odometer records the distance of
individual trips. Before each trip, set the trip
odometer to zero by pushing the reset button.
File:05iclgf.ex
Update:Wed Jan 24 14:32:51 1996

85 [SC02900(ALL)07/93]
one third page art:0032175-A
Turn signal
*
[SC03100(ALL)03/95]
Windshield Wipers and Washer
*
[SC03200(ALL)08/91]
To operate the windshield wipers and washers,
make sure your ignition key is turned to the ON
position.
[SC03250(ALL)07/93]
The windshield wipers can be operated by
moving the control lever. The standard wipers
have two speeds and the optional wipers have
three speeds.
[SC03400(ALL)07/93]
To operate the standard wipers, pull the lever
down to the first stop (LO). For high speed
operation, pull the lever down to the second
stop (HI).
[SC03450(ALL)03/94]
The optional wipers have a third position which
provides intermittent wiper operation. For preset
interval intermittent wiper operation, pull the
lever down to the first stop (INT). For normal
operation pull the lever down to the second stop
(LO), or for high operation pull the lever down
to the third stop (HI).
File:07icscf.ex
Update:Wed Jan 24 14:50:00 1996

109
*
[AS21380(ALL)05/95]
Electronic Stereo and Stereo
Cassette Radios
*
[AS21400(ALL)06/95]
Using the Controls on Your New Radio
*
[AS21500(ALL)02/95]
How to turn the radio on and adjust the
volume
*
[AS21600(ALL)06/95]
Press the ªPOWERº button to turn the radio on.
Press it again to turn it off.
*
[AS22050(ALL)05/95]
Press the right (+) side of the ªVOLUMEº
button to increase the volume. Press the left (s)
side of the button to decrease the volume.
Illuminated bars in the display show the relative
volume level.
*
[AS22075(ALL)07/95]
NOTE: If the volume level is set above a
certain listening level when the
ignition switch is turned off, when the
ignition switch is turned back on, the
volume will come back to a ªnominalº
listening level. However, if the radio
power is turned off (with the
ªPOWERº button), the volume will
remain in the position it was set at
when radio power was turned off.
*
[AS22100(ALL)06/95]
Selecting the AM or FM frequency band
*
[AS22210(ALL)07/95]
Push the ªAM/FMº button to select the desired
frequency band. Pushing the button more than
once will alternate between AM, FM1 and FM2.
These functions are used with the station
memory buttons described underHow to tune
radio stations.
*
[AS22300(ALL)05/95]
How to tune radio stations (Stereo Radio)
*
[AS22400(ALL)05/95]
There are three ways for you to tune in to a
particular station. You can manually locate the
station by using the ªTUNEº button, ªSEEKº the
station or select the station by using the memory
preset buttons, which you can set to any desired
frequency.
File:09icasf.ex
Update:Wed Jan 24 14:52:32 1996

111
*
[AS23150(ALL)02/95]
q
Using the ªSCANº function (Stereo Cassette
Radio)
*
[AS23175(ALL)06/95]
Press the ªSCANº button to enter the scan
mode. The radio will begin scanning up the
frequency band, stopping on each listenable
station for approximately a five-second
sampling. This continues until you press the
ªSCANº button a second time.
*
[AS23200(ALL)04/95]
q
Setting the Station Memory Preset buttons
*
[AS23300(ALL)05/95]
Your radio is equipped with 5 station
memory buttons. These buttons can be used
to select up to 5 preset AM stations and 10
preset FM stations (5 in FM1 and 5 in FM2).
*
[AS23400(ALL)06/95]
Follow the easy steps below to set these buttons
to the desired frequencies:
*
[AS23500(ALL)07/95]
1. Select a band, then select a frequency.
*
[AS23700(ALL)06/95]
2. Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now held in memory on that
button.
*
[AS23800(ALL)06/95]
3. Follow the two steps above for each station
memory preset button you want to set.
*
[AS23900(ALL)04/95]
NOTE: If the vehicle's battery is disconnected,
the clock and station memory preset
buttons (if programmed in auto mode)
will need to be reset.
File:09icasf.ex
Update:Wed Jan 24 14:52:32 1996

149 [RE10200(ALL)03/95]
6. Lower the vehicle by turning the jack handle
counterclockwise.
[RE10500(ALL)02/95]
7. Remove the jack and fully tighten the wheel
lug bolts in the order shown in the
illustration under Step 1.
[RE10700(ALL)02/95]
8. Put the tire, jack, retaining tool and wrench
away.
[RE10750(ALL)02/95]
9. Secure the conventional tire where the spare
was stored with the bolt provided.
[RE10850(ALL)02/95]
10. Unblock the wheels.
*
[RE12150(ALL)12/91]
If the Engine Cranks but Does
Not Start or Starting After a
Collision
*
[RE12225(ALL)07/95]
If the engine cranks but does not start or if you
have had a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device that stops the fuel pump
when your vehicle has been involved in a
substantial jolt.
*
[RE12250(ALL)07/95]
For information on how to check and reset the
fuel pump shut-off switch, seeFuel pump shut-off
switchin the Index.
*
[RE12300(ALL)05/95]
Towing Your Vehicle
[RE12500(ALL)07/95]
If you need to have your vehicle towed, contact
a professional towing service or, if you are a
member, your roadside assistance center.
Suggested towing options include wheel lift
towing or flat bed towing.
File:12icref.ex
Update:Wed Jan 24 14:52:09 1996

223 [SV37600(ALL)05/93]
Circuit Breaker
[SV37700(ALL)05/93]
The climate control systems require high
amperage. If the rated amperage is exceeded, a
protective circuit breaker will open.
[SV37800(ALL)07/93]
If the circuit is broken by the circuit breaker,
turn all heater and air-conditioner switches off
and restore the circuit by pushing the reset
button located in the interior fuse panel. If the
circuit breaks again, have it inspected by your
dealer.
[SV37900(ALL)07/93]
one third page art:0032233-B
Reset button for circuit breaker
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

232
*
[SV48700(ALL)02/92]
Never use a metal exhaust collector when you
service your vehicle. If the metal collector
contacts any of your vehicle's plastic trim or
bumper parts they could melt or deform.
*
[SV48800(ALL)01/95]
Do not drive your vehicle if it does not operate
properly. See your dealer if the engine runs on
for more than five seconds after you shut it off
or if it misfires, surges, stalls, or backfires.
%*
[SV48900(ALL)05/95]
Information about your vehicle's emission
control system is on the Vehicle Emission
Control Information decal located on or near the
engine. This decal identifies engine displacement
and gives some tune-up specifications.
%*
[SV48910(ALL)07/95]
Readiness for Inspection/Maintenance
Testing
*
[SV48920(ALL)07/95]
In some localities it may become a legal
requirement to pass an Inspection/
Maintenance (I/M) test of the On-Board
Diagnostic (OBD) II system. If the vehicle's
powertrain system or its battery has just been
serviced, the OBD II system is reset to a not
ready for I/M testing condition. To prepare for
I/M testing, the law specifies a ªneed for
additional mixed city and highway driving to
complete the checkº of the OBD II system. As
soon as all of the OBD II system checks are
successfully completed, the OBD II system is set
to the ready condition. The amount of driving
required to reach the ready condition varies with
individual driving patterns. To complete this
requirement in the minimum amount of time,
refer to the OBD II Drive Cycle defined below. If
the vehicle owner cannot or does not want to do
the additional driving required by law, a service
center can perform this drive cycle as it would
any other type of repair work.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996