Electrical FORD FIESTA 2007 Owners Manual

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01A-78 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303=01 A178
REMOVAL
Discard the snap ring.
53. Remove the engine support insulator.
52. CAUTIONS: Vehicles with automated gearshift
AUPPO~~ the halfshaft. The inner joint 54. Remove the gearshift actuator cover. must not be bent more than 18 degrees.
The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft oil seal.
N0TE:Plug the transaxle to prevent oil loss or dirt
ingress.
Detach the right-hand halfshaft and the
intermediate shaft from the transaxle and
secure
it to one side.
Discard the center bearing cap and locknuts.
Allow the oil to drain into a suitable container.
55.
Disconnect the gearshift actuator electrical
connector (colored black).
2006.0 Fiesta 1212006 GII 31 63en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)llm4L
303-01A-79 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-79
REMOVAL
56. Disconnect the gearshift actuator electrical Remove the spring clip.
, connector (colored gey).
59. Remove the gearshift cables cover.
57m ACAUTION:I brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
Disconnect the clutch slave cylinder supply
line.
Remove the spring clip.
Vehicles without automated gearshift
58' ACAUTION:~ brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
Disconnect the clutch slave cylinder supply
line.
60. Detach the gearshift cables from the
transaxle.
Detach the gearshift cables and the selector
cable from the selector levers.
Turn the abutment sleeve clockwise and
detach the cables from the bracket.
All vehicles
'Irn ~CAUTION:DO not support the engine
directly on the oil pan.
2006.0 Fiesta 12/2oo6 G113163en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-0 I Am82 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 Am82
REMOVAL
Lifting Bracket, Engine
303-1 22 (21 -068A)
Engine - Vehicles With: Automatic Transaxle
Special Tool(s) present and may ignite. Failure to follow (.
2. Remove the air cleaner.
622
For additional information, refer to: Air
Cleaner - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V
(Sigma) (303-12 Intake Air Distribution and
Filtering, Removal and Installation).
I I 1 3. Drain the cooling system.
Wrench, Hydraulic Line Union
"-269 (13-027)
I I Remover/lnstaller, Hose I
these instructions may result in personal
injury.
1. Release the fuel system pressure.
For
additional information, refer to: Fuel
System Pressure Release (31 0-00 Fuel
System - General Information, General
Procedures).
General Eaui~ment
I Engine hoist I
I Securing straps I
I Workshop table I
All vehicles
WARNINGS:
A Refer to the Material Safety Data Sheets
for the Automatic Transmission
Fluid
E-AW. Failure to follow this instruction may
result in personal injury. Certain
Transmission and Power Steering fluids
supplied to Ford contain additives which
may cause skin irritation or other skin
reactions after contact.
For
additional information, refer to: Health
and Safety Precautions (1 00-00 General
Information, Description and Operation).
See
- Transmission Fluids.
A Do not smoke or carry lighted tobacco or
open flame of any type when working on
or near any
fuel related components.
Highly flammable vapors are always
For additional information, refer to: Cooling
System Draining, Filling and Bleeding -
1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma)llm3L Duratec-8V (Rocam) (303-03A,
General Procedures). ,'
4. Remove the front wheels and tires. C'
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
and Installation).
5. Disconnect the powertrain control module
(PCM) electrical connector.
For
additional information, refer to:
Powertrain
Control Module (PCM) - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-14
Electronic Engine Controls, Removal and
Installation).
6. Loosen the strut and spring assembly top
mount nuts by three turns on both sides.
--
2006.0 Fiesta 1212006 G380458en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
Duratec-I 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
REMOVAL
13. Disconnect the low pressure evaporate 16. Using the special tool, disconnect the
emission
(EVAP) hose from the EVAP valve. coolant hose from the coolant distribution
housing.
14. Detach the brake booster vacuum line from
the intake manifold.
17. Disconnect the heated oxygen (HOZS)
sensor electrical connector.
15. Using the special tool, disconnect the
coolant hose from the coolant distribution
18. Disconnect the catalyst monitor sensor
housing. electrical connector.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
Duratec-1 6V (Sigma)/l.6L Duratec-I 6V (Sigma)
REMOVAL
19. Disconnect the power steering pressure 22.
Disconnect the engine wiring harness
(PSP) switch electrical connector. electrical
connector.
I
20. Detach the power steering line support 23. Disconnect
the EVAP electrical connector.
bracket from the cylinder head.
24. Disconnect the knock sensor (KS) electrical
21. Detach the power steering line from the connector.
power steering pump mounting bracket.
2006.0 Fiesta 121200'6 G380458en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)lIl4L
303-01 A-86 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-86
REMOVAL
25. Disconnect the generator electrical
connectors. 29. Detach the engine ground cable from the
transaxle.
J
26. Remove the right-hand headlamp assembly.
30. Remove the engine wiring harness support
For additional information, refer to: brackets.
Headlamp Assembly
(41 7-01 Exterior
Lighting, Removal and Installation).
27. Disconnect the engine coolant temperature
(ECT) electrical connector.
28. Disconnect the electronic ignition (El) coil
electrical connector. 31.
Disconnect the turbine shaft speed (TSS)
sensor electrical connector.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) - ---
REMOVAL
32. Detach the ground cable from the transaxle. 35.
Disconnect the transmission range (TR)
sensor electrical connector.
33. Disconnect the transaxle breather hose.
36. Detach the selector lever cable from the
transaxle.
34. Disconnect the transaxle wiring harness
electrical connector.
37. Detach the selector lever retaining bracket
from the transaxle.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
303-01 Am88 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303101 A-88
REMOVAL
38. Disconnect the vehicle speed (VSS) sensor
40. Disconnect the oil pressure switch
electrical connector. electrical connector.
/
39. N0TE:Mark the position of the transmission
fluid cooler supply line and the
transmission fluid cooler return line.
Disconnect the transmission fluid cooler
lines from the transaxle.
For additional information, refer to: Health
and Safety Precautions
(1 00-00 General
Information, Description and Operation).
See
- Transmission Fluids.
Allow the fluid to drain into a suitable
container.
For additional information, refer to: Health and Safety Precautions
(1 00-00 General
Information, Description and Operation).
See
- Transmission Fluids.
41. Raise and support the vehicle.
For additional information, refer to: Lifting
(1 00-02 Jacking and Lifting, Description
and Operation).
42. Disconnect the crankshaft position (CKP)
sensor electrical connector.
43. Disconnect the ignition switch to starter
motor solenoid and battery to starter motor
solenoid cables.
2006.0 Fiesta la2006 G380458en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-89 Duratec-1 6V (Sigma)ll.GL Duratec-1 6V (Sigma) 303-01 A-89
REMOVAL
44m ACAUTION:~~~~ bending of the exhaust Vehicles with air conditioning
I flexible pipe may cause damage resulting 47.
Disconnect the air conditioning (NC)
, in failure. low-pressure cutoff switch electrical
Support the exhaust
flexible pipe with a connector.
suitable support
wrap or suitable splint.
48. Disconnect the NC compressor clutch
45. Detach the exhaust flexible pipe from the electrical connector.
catalytic converter.
Discard the nuts and the gasket.
46. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive
Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive, Removal and
Installation)
I Accessory Drive Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles Without: Air Conditioning
(303-05 Accessory Drive,
Removal and
Installation).
49. Disconnect the NC high-pressure cutoff
switch
electrical connector.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
REMOVAL
54. Disconnect the cooling fan motor and 57. Using the special tool, disconnect the
. cooling fan resistor electrical connectors. coolant
hose from the distribution pipe.
55. Remove the cooling fan motor and shroud. 58. Detach the lower arm from the wheel
1. Release the cooling fan motor and shroud knuckle on both sides.
from the retaining brackets. Remove
the heat shield.
2. Push the cooling fan motor and shroud
upwards and then downwards to remove.
Asupport the halfshaft. The inner joint 56. Using the special tool, disconnect the
must not be bent more than 18 degrees.
coolant hose from the radiator.
The outer joint must not be bent more than
'i
45 degrees.
59. CAUTIONS:
ADO not damage the halfshaft seal.
N0TE:Plug the transaxle to prevent fluid loss or
dirt ingress.
For additional information, refer to: Health and
Safety Precautions
(1 00-00 General Information,
Description and Operation).
See
- Transmission Fluids.
Using a suitable tire lever, detach the
left-hand halfshaft from the transaxle and
secure
it to one side.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com