wheel FORD MUSTANG 2003 Workshop Manual

IN-
VEHICLE REPAIR
Axle Shaft
Removal 1. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the rear brake disc (2C026). For additional information, refer to Section 206 - 04 .
4. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
5. Remove the differential pinion shaft (4211). 1. Remove the differential pinion shaft lock bolt (4241).
2. Remove the differential pinion shaft.
6. CAUTION: Do not damage the rubber O- ring in the axle shaft groove.
Remove the U- washer (4N237).
1. Push the axle shafts (4234) inboard.
2. Remove the U- washer.
7. CAUTION: Damage to the rear brake anti- lock sensor (2C190) may occur if it is not
removed before the axle shaft.
Carefully remove the rear brake anti- lock sensor. For additional information, refer to Section SECTION 205-
02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring
Gear 2003 Mustang Workshop
Manual Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

206 - 09A .
8. CAUTION: Do not damage the wheel bearing oil seal.
Remove the axle shaft.
Installation 1. Lubricate the lip of the wheel bearing oil seal zUse Premium Long- Life Grease XG-1-C or equivalent meeting Ford specification ESA-
M1C75- B.
2. CAUTION: Do not damage the wheel bearing oil seal.
Install the two axle shafts.
3. CAUTION: Do not damage the rubber O- ring in the axle shaft groove.
Install the U- washer. Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. Position the two U-
washers on the button end of the axle shaft.
2. Pull the axle shaft outward.
4. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and
Sealer EOAZ- 19554-AA or equivalent meeting Ford specification WSK-M2G351- A5 prior to
installation.
Install the differential pinion shaft. 1. Align the hole in the differential pinion shaft with the case lock bolt hole.
2. Install a new differential pinion shaft lock bolt.
5. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
6. Install the rear brake anti- lock sensor. For additional information, refer to Section 206 - 09A .
7. Install the rear brakes. For additional information, refer to Section 206 - 04 .
8. Install the tire and wheel assembly. For additional information, refer to Section 204 - 04 .
9. Lower the vehicle. Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Rear Wheel Bearing and Axle Shaft Oil Seal
Removal 1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
2. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
SECTION 205-
02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring
Gear 2003 Mustang Workshop
Manual Special Tool(s)
Adapter for 303-
224
205- 153 (T80T-4000- W) Installer, Axle Shaft Bearing
205-
124 (T78P-1225- A) Installer, Rear Axle Oil Seal
205-
390 (T97T-1177- B) Remover, Axle Bearing
205-
219 (T85L-1225- AH) Slide Hammer
100-
001 (T50T-100- A) Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Installation
1. Lubricate the new rear wheel bearing with the specified lubricant.
2. Using the special tools, install the new rear wheel bearing.
3. Lubricate the lip of the new wheel bearing oil seal. zUse Premium Long- Life Grease XG-1-C or equivalent meeting Ford specification ESA-
M1C75- B.
4. Using the special tools, install the new wheel bearing oil seal.
5. Install the axle shaft. For additional information, refer to Axle Shaft in this section. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Drive Pinion Flange and Drive Pinion Seal
Removal 1. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. Remove the rear wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
3. CAUTION: Remove the rear brake calipers to prevent drag during the drive pinion
bearing preload adjustment.
CAUTION: Do not allow the calipers to hang from the brake hoses.
Remove the rear brake caliper and support bracket from the knuckle as an assembly. Wire the
caliper and support bracket assembly out of the way. For additional information, refer to Section 206 - 04 .
4. CAUTION: Index- mark the driveshaft flange and pinion flange (4851) to maintain
initial balance during installation.
CAUTION: The driveshaft centering socket yoke fits tightly on the pinion flange
pilot. Never hammer on the driveshaft or any of its components to disconnect the yoke
from the flange. Pry only in the area shown, with a suitable tool, to disconnect the yoke
from the flange.
Disconnect and position the driveshaft out of the way. For additional information, refer to
SECTION 205-
02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring
Gear 2003 Mustang Workshop
Manual Special Tool(s)
2-
Jaw Puller
205- D072 (D97L-4221- A) or
equivalent Holding Fixture, Drive Pinion
Flange
205-
126 (T78P-4851- A) Installer, Drive Pinion Flange
205-
002 (TOOL- 4858-E) or
equivalent Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

7. Install the rear brake calipers. For additional information, refer to
Section 206 - 04 .
8. Install the rear wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
9. Lower the vehicle. Klj . 5 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Axle Assembly
Removal and Installation
1. CAUTION: The vehicle must be on level ground and at curb height.
Mark the rear shock absorbers relative to their protective sleeve. zDuring installation, raise the suspension to this reference mark before tightening the
suspension fasteners.
2. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
3. Remove the rear wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
4. CAUTION: Index- mark the driveshaft flange and pinion flange (4851) to maintain
initial balance during installation.
CAUTION: The driveshaft centering socket yoke fits tightly on the pinion flange
pilot. Never hammer on the driveshaft or any of its components to disconnect the yoke
from the flange. Pry only in the area shown, with a suitable tool, to disconnect the yoke
from the flange.
Disconnect and position the driveshaft out of the way. For additional information, refer to
Section 205 - 01 .
SECTION 205-
02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring
Gear 2003 Mustang Workshop
Manual Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5.
NOTE: If necessary, use Rust Penetrant and Inhibitor F2AZ-19A501- A meeting Ford
specification ESR-M99C56- A to loosen the sensor for removal.
Remove the rear anti- lock brake sensors from the rear disc brake adapters. For additional
information, refer to Section 206 - 09A .
6. CAUTION: Index- mark the brake discs and the wheel studs prior to brake disc
removal.
CAUTION: Do not allow the calipers to hang from the brake hoses.
Remove the rear brake discs. For additional information, refer to Section 206 - 04 .
7. CAUTION: Secure the differential housing (4010) to the jack with a suitable strap.
Support the differential housing with a suitable hi- lift jack. Klj . 2 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

12. Disconnect the lower suspension arm and bushings from the axle.
13. Remove the axle from the vehicle.
14.
CAUTION: Align the index marks on the driveshaft centering socket yoke and the
pinion flange.
CAUTION: Install the driveshaft with new bolts. If new bolts are not available, apply
Threadlock and Sealer EOAZ-19554- AA or equivalent meeting Ford specification WSK-
M2G351- A5 to the threads of the original bolts.
CAUTION: The driveshaft centering socket yoke fits tightly on the pinion flange
pilot. To make sure that the yoke seats squarely on the flange, tighten the bolts evenly in
a cross pattern as shown.
CAUTION: Raise the suspension to the reference marks on the rear shock
absorbers before tightening the suspension fasteners.
NOTE: Apply High Temperature Nickel Anti- Sieze Lubricant F6AZ-9L494-AA meeting Ford
specification ESE-M124A- A to the rear anti-lock brake sensor body where it will make contact
when installed.
To install, reverse the removal procedure.
zRefer to Section 204 - 02 for rear suspension fastener tightening specifications.
z Refer to Section 204 - 04 for wheel nut tightening specification.
z Check and, if necessary, fill the axle with the specified lubricant to the specified level. For
additional information, refer to Specifications in this section. Klj . 4 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...