AC system FORD MUSTANG 2003 Workshop Manual

6. Remove the pump motor electrical connector.
7. Remove the anti-
lock-brake control module screws.
8. Remove the anti- lock-brake control module from the HCU.
Installation 1. NOTE: The brake system must be bled after the HCU is installed or replaced. Refer to Section 206 - 00 .
To install, reverse the removal procedure. Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Module
Removal
1. Remove the hydraulic control unit (HCU). Refer to Hydraulic Control Unit .
2. Remove the pump motor electrical connector.
3. Remove the anti- lock-brake control module screws.
4. Remove the anti- lock-brake control module from the HCU.
Installation
1. NOTE: The brake system must be bled after the HCU is installed or replaced. Refer to Section 206 - 00 .
To install, reverse the removal procedure.
SECTION 206-
09A: Anti-Lock Control — Rear 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Anti-
Lock Control — Traction Control
The four wheel anti- lock brake system (4WABS) with traction control consists of the following
components:
zanti- lock brake control module (2C346)
z front anti- lock brake sensor (2C204)/(2C205)
z front anti- lock brake sensor indicator (2C182)
z hydraulic control unit (2C286)
z powertrain control module (12A650)
z rear anti- lock brake sensor (2C190)/(2C216)
z rear anti- lock brake sensor indicator (2C189)
z traction control switch
z yellow anti- lock brake system (ABS) warning indicator
SECTION 206-
09B: Anti-Lock Control — Traction Control 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Anti-
Lock Control — Traction Control
Refer to Wiring Diagrams Cell 42 , Anti-
Lock Brake System for schematic and connector information.
Principles of Operation
The anti- lock-brake control module receives wheel speed readings from each anti- lock brake sensor
and processes this information to determine if an ABS event is necessary. The anti- lock brake sensor
electrically senses each tooth of the anti- lock brake sensor indicators as it passes through the anti- lock
brake sensor's magnetic field.
The anti- lock brake control module continuously monitors and compares the rotational speed of each
wheel and, when it detects an impending wheel lock, modulates brake pressure to the appropriate
brake caliper. This is accomplished by triggering the hydraulic control unit (HCU) to open and close the
appropriate solenoid valves. Once the affected wheel returns to normal speed, the anti- lock brake
control module returns the solenoid valves to their normal position, and normal (base) braking
resumes.
The anti- lock brake control module is self- monitoring. When the ignition switch is turned to the RUN
position, the anti- lock brake control module will do a preliminary electrical check, and at approximately
12 km/h (8 mph) the pump motor is turned on for approximately one half- second. Also during all
phases of operation the anti- lock brake control module (after the vehicle is in motion) checks for
correct operation of the anti- lock brake sensors. Any malfunction of the ABS will cause the ABS to shut
off and ABS warning indicator to illuminate; normal power assisted braking, however, remains.
The ABS control module has the ability to store multiple DTCs in memory.
The traction control system controls wheelspin by modulating the engine torque by communicating to
the powertrain control module (PCM) and by applying, then releasing, the appropriate brake to restore
traction when one or both drive wheels lose traction and begin to spin during acceleration.
The traction control system can be disabled by depressing the traction control switch. The traction
control system will reset and return to normal traction assist when the ignition switch is cycled or when
the traction control switch is depressed again. SECTION 206-
09B: Anti-Lock Control — Traction Control 2003 Mustang Workshop Manual Special Tool(s)
Worldwide Diagnostic System
(WDS)
418-
F224,
New Generation STAR (NGS)
Tester
418- F052, or equivalent scan
tool 73 Digital Multimeter or
equivalent
105-
R0051 Klj . 1 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Inspection and Verification
1. Verify the customer concern by operating the system.
2. Visually inspect for obvious signs of mechanical and electrical damage.
3. If the concern remains after the inspection, connect the scan tool to the data link connector (DLC) located beneath the instrument panel and select the vehicle to be tested from the scan
tool menu. If the scan tool does not communicate with the vehicle: 1. Check that the program card is correctly installed.
2. Check the connections to the vehicle.
3. Check the ignition switch position.
4. If the scan tool still does not communicate with the vehicle, refer to the scan tool manual.
5. Carry out the DATA LINK DIAGNOSTIC TEST. If the scan tool responds with: 1. CKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418-00.
2. NO RESP/NOT EQUIP for the anti- lock brake control module, Go To Pinpoint Test A .
3. SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs and carry out self- test diagnostics for the anti-lock brake
control module.
6. If the DTCs retrieved are related to the concern, go to the Anti- Lock Brake Control Module
Diagnostic Trouble Code (DTC) Index to continue diagnostics.
7. If no DTCs related to the concern are retrieved, GO to Symptom Chart to continue diagnostics.
Anti-Lock Brake Control Module Diagnostic Trouble Code (DTC) Index
NOTE: If a wheel speed signal fault or a pump motor fault is detected, the yellow ABS warning
indicator cannot be reset with the key OFF and key ON method. The vehicle must be driven over 12
km/h (8 mph) for the anti- lock brake control module to do a re- check of the system before the yellow
ABS warning indicator is turned OFF. Visual Inspection Chart Mechanical Electrical
z
Low brake fluid
z Anti- lock brake sensor
z Anti- lock brake sensor indicator
z Base brake system
z Wheel bearings z
Central junction box (CJB) Fuse:
„5 (15A)
„ 15 (10A)
„ 29 (15A)
„ 33 (15A)
„ 35 (15A)
z Battery junction box (BJB) Fuse:
„ABS 1 (50A)
„ ABS 2 (20A)
z Circuitry
z Damaged or corroded connectors
z ABS warning indicator
z Loose grounds Klj . 2 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Anti-Lock Brake Control Module Diagnostic Trouble Code (DTC) Index
DTC Description Source Action
B1318 Battery Voltage Low ABS/TC Go To Pinpoint Test C .
B1342 ECU Is Defective ABS/TC INSTALL a new anti-
lock brake control
module; REFER to Module . REPEAT the
self- test. B1484 Brake Pedal Input Open Circuit ABS/TC Go To Pinpoint Test D .
B1596 Repair Continuous Codes ABS/TC REPAIR the DTCs retrieved.
C1095 ABS Hydraulic Pump Motor Circuit
Failure ABS/TC Go To Pinpoint Test E .
C1145 RF Anti-
Lock Brake Sensor Input
Circuit Failure ABS/TC Go To Pinpoint Test F .
C1155 LF Anti-
Lock Brake Sensor Input
Circuit Failure ABS/TC Go To Pinpoint Test F .
C1165 RR Anti-
Lock Brake Sensor Input
Circuit Failure ABS/TC Go To Pinpoint Test F .
C1175 LR Anti-
Lock Brake Sensor Input
Circuit Failure ABS/TC Go To Pinpoint Test F .
C1222 Anti-
Lock Brake Sensor Mismatch ABS/TC Go To Pinpoint Test G .
C1233 LF Anti-
Lock Brake Sensor Input
Signal Missing ABS/TC Go To Pinpoint Test H .
C1234 RF Anti-
Lock Brake Sensor Input
Signal Missing ABS/TC Go To Pinpoint Test H .
C1235 RR Anti-
Lock Brake Sensor Input
Signal Missing ABS/TC Go To Pinpoint Test H .
C1236 LR Anti-
Lock Brake Sensor Input
Signal Missing ABS/TC Go To Pinpoint Test H .
C1266 ABS Valve Power Relay Circuit
Failure ABS/TC INSTALL a new anti-
lock brake control
module; REFER to Module . REPEAT the
self- test. C1805 Mismatched PCM and/or Anti-Lock
Brake Control Module ABS/TC CLEAR the DTCs. RETRIEVE the DTCs. If
DTC C1805 is retrieved, check the PCM
and Anti- Lock Brake Control Module is for
the correct vehicle. INSTALL a new PCM or
anti-lock brake control module as
necessary. CLEAR the DTCs. REPEAT the self-test. U1009 SCP (J1850) Invalid or Missing Data
for Engine Torque ABS/TC CARRY OUT the PCM self-
test. U1027 SCP (J1850) Invalid or Missing Data
for Engine RPM ABS/TC CARRY OUT the PCM self-
test. U1059 SCP (J1850) Invalid or Missing Data
for Transmission/Transaxle/PRNDL ABS/TC CARRY OUT the PCM self-
test. U1083 SCP (J1850) Invalid or Missing Data
for Engine Systems ABS/TC CARRY OUT the PCM self-
test. U1262 SCP (J1850) Communication Bus
Fault ABS/TC REFER to
Section 418 - 00 . Klj . 3 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Pinpoint Tests
PINPOINT TEST A: NO COMMUNICATION WITH THE ANTI-
LOCK
BRAKE CONTROL MODULE test. Condition
Possible Sources Action
z No communication with the anti-
lock brake control module z
CJB Fuse 29
(15A).
z Circuitry.
z Anti- lock brake
control module. z
Go To Pinpoint Test A .
z Unable to enter self- test zAnti- lock brake
control module. z
Go To Pinpoint Test B .
z The yellow ABS warning indicator
does not self- check z
Circuitry.
z Anti- lock brake
control module.
z Instrument
cluster. z
Go To Pinpoint Test I .
z Spongy brake pedal with no
warning indicator z
Air in the brake
system.
z Base brake
system.
z Hydraulic control
unit (HCU). z
Go To Pinpoint Test J .
z REFER to
Section 206 -
00 .
z Poor vehicle tracking during anti-
lock function z
Air in the brake
system.
z Hydraulic control
unit (HCU).
z Base brake
system. z
Go To Pinpoint Test K .
z REFER to
Section 206 -
00 .
z The traction control is
inoperative— does not operate
correctly z
CJB 5 (15A).
z Circuitry.
z Traction control
switch.
z Instrument
cluster.
z Anti- lock brake
control module. z
Go To Pinpoint Test L .
z The traction control indicator is
inoperative— traction control
switch z
Circuitry.
z Traction control
switch.
z Instrument
cluster. z
Go To Pinpoint Test M .
Test Step Result / Action to
Take A1 CHECK CIRCUIT 601 (LB/PK) FOR AN OPEN
z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C141.
z Key in ON position.
z Measure the voltage between anti- lock brake control module C141
Pin 8, Circuit 601 (LB/PK), harness side and ground. Yes
GO to
A2 .
No
REPAIR the circuit. Klj . 6 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST H: DTC C1233 (LF), C1234 (RF), C1235 (RR), C1236
(LR), ANTI-
LOCK BRAKE SENSOR INPUT SIGNAL MISSING
PINPOINT TEST I: THE YELLOW ABS WARNING INDICATOR DOES
NOT SELF- CHECK mode on the diagnostic tool:
CLEAR the DTCs.
z Key in OFF position.
z Key in ON position.
z Test drive the vehicle over 24
km/h (15 mph).
z Enter the following diagnostic
mode on the diagnostic tool:
Retrieve DTCs.
z Is DTC C1222 retrieved? INSTALL a new anti-
lock brake control module;
REFER to Module . REPEAT the self-
test.
No
If another DTC is retrieved, GO to the Anti- Lock Brake
Control Module Diagnostic Trouble Code (DTC) index.
If no DTCs are retrieved, system is OK. Test Step Result / Action to Take
H1 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR z
Check the suspect anti- lock brake sensor
mounting.
z Check the suspect anti- lock brake sensor for
excessive dirt build up, obstructions, and
damage.
z Is the suspect anti- lock brake sensor and
mounting OK? Yes
GO to
H2 .
No
REPAIR as necessary. CLEAR the
DTCs. REPEAT the self- test. H2 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR INDICATOR z
Check the suspect anti- lock brake sensor
indicator for corrosion, nicks, bridged teeth,
damaged teeth, correct mounting, and
alignment with the anti- lock brake sensor.
z Check the air gap and bearing end play.
z Is the suspect anti- lock brake sensor
indicator OK? Yes
GO to
H3 .
No
INSTALL a new anti- lock brake sensor
indicator; REFER to Sensor Indicator —
Front or
Sensor Indicator — Rear .
CLEAR the DTCs. REPEAT the self- test. H3 CHECK THE ANTI-
LOCK BRAKE SENSOR
OUTPUT z
Key in ON position.
z Enter the following diagnostic mode on the
diagnostic tool: CLEAR the DTCs.
z Key in OFF position.
z Key in ON position.
z Have an assistant monitor the anti- lock brake
control module PIDs LF_WSPD, RF_WSPD,
LR_WSPD, and RR_WSPD while driving at
various speeds.
z NOTE: the vehicle must be driven 16 km (10
miles) during this test step.
z Test drive the vehicle for 16 km (10 miles).
z Are the anti- lock brake control module PIDs
approximately the same at all times? Yes
INSTALL a new anti-
lock brake control
module; REFER to Module . REPEAT
the self- test.
No
INSTALL a new anti- lock brake sensor;
REFER to Sensor — Front or
Sensor —
Rear . CLEAR the DTCs. REPEAT the
self- test. Klj . 14 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST J: SPONGY BRAKE PEDAL WITH NO WARNING
INDICATOR
PINPOINT TEST K: POOR VEHICLE TRACKING DURING ANTI-
LOCK
FUNCTION Test Step Result / Action to Take
I1 CHECK THE ABS WARNING INDICATOR CIRCUITRY
z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C141.
z Key in ON position.
z Depress and release the shorting bar connector
internal to the anti- lock brake control module C141,
harness side, while checking the yellow ABS warning
indicator in the instrument cluster.
z Does the yellow ABS indicator illuminate with the
shorting bar released and OFF with the shorting
bar depressed? Yes
INSTALL a new anti-
lock brake
control module; REFER to
Module . TEST the system for
normal operation.
No
REFER to Section 413 - 01 .
Test Step Result / Action to Take
J1 CHECK THE VEHICLE COMPONENTS
z
Check the brake pedal and power
booster/brake master cylinder for correct
attachment.
z Are the components OK? Yes
GO to
J2 .
No
REPAIR as necessary. TEST the system for
normal operation. J2 BLEED THE BRAKE SYSTEM
z
Bleed the brake system; REFER to Section 206 - 00 .
z Check for spongy brake pedal.
z Is the brake pedal spongy? Yes
INSTALL a new HCU; REFER to
Hydraulic Control Unit . TEST the system for normal
operation.
No
The brake system is OK. TEST the system
for normal operation. Test Step Result / Action to Take
K1 BLEED THE BRAKE SYSTEM
z
Bleed the brake system; REFER to Section 206 - 00 .
z Check for vehicle tracking poorly.
z Does the vehicle track poorly? Yes
GO to
K2 .
No
The brake system is OK. TEST the
system for normal operation. K2 CHECK THE LF ABS VALVE OPERATION
z
Lift the vehicle and rotate all the wheels to
make sure they rotate freely (the vehicle must
be in neutral).
z NOTE: Trigger must be depressed twice.
Each depress runs the pump motor for two
seconds. Yes
INSTALL a new HCU; REFER to
Hydraulic Control Unit
. TEST the system
for normal operation.
No Klj . 15 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Trigger the anti- lock brake control module
active command PMP MOTOR ON for four
seconds.
z Apply moderate brake pedal effort.
z Have an assistant attempt to rotate the LF
wheel while the pump motor is running.
z Does the LF wheel rotate? GO to
K3 .
K3 CHECK THE LF ABS VALVE RELEASE
z
Apply moderate brake pedal effort.
z Trigger the anti- lock brake control module
active command LF INLET and LF OUTLET.
z NOTE: Trigger must be depressed twice.
Each depress runs the pump motor for two
seconds.
z Have an assistant rotate the LF wheel
immediately after depressing trigger.
z Does the LF wheel rotate? Yes
GO to
K4 .
No
GO to K10 .
K4 CHECK THE RF ABS VALVE OPERATION
z
NOTE: Trigger must be depressed twice.
Each depress runs the pump motor for two
seconds.
z Trigger the anti- lock brake control module
active command PMP MOTOR ON for four
seconds.
z Apply moderate brake pedal effort.
z Have an assistant attempt to rotate the RF
wheel while the pump motor is running.
z Does the RF wheel rotate? Yes
INSTALL a new HCU; REFER to
Hydraulic Control Unit
. TEST the system
for normal operation.
No
GO to K5 .
K5 CHECK THE RF ABS VALVE RELEASE
z
Apply moderate brake pedal effort.
z Trigger the anti- lock brake control module
active command RF INLET and RF OUTLET.
z NOTE: The scan tool will energize the valves
for only two seconds per trigger press.
z Have an assistant rotate the RF wheel
immediately after depressing trigger.
z Does the RF wheel rotate? Yes
GO to
K6 .
No
GO to K10 .
K6 CHECK THE LR ABS VALVE OPERATION
z
NOTE: Trigger must be depressed twice.
Each depress runs the pump motor for two
seconds.
z Trigger the anti- lock brake control module
active command PMP MOTOR ON for four
seconds.
z Apply moderate brake pedal effort.
z Have an assistant attempt to rotate the LR
wheel while the pump motor is running.
z Does the LR wheel rotate? Yes
INSTALL a new HCU; REFER to
Hydraulic Control Unit
. TEST the system
for normal operation.
No
GO to K7 .
K7 CHECK THE LR ABS VALVE RELEASE
z
Apply moderate brake pedal effort.
z Trigger the anti- lock brake control module
active command LR INLET and LR OUTLET.
z NOTE: The scan tool will energize the valves
for only two seconds per trigger press.
z Have an assistant rotate the LR wheel
immediately after depressing trigger.
z Does the LR wheel rotate? Yes
GO to
K8 .
No
GO to K10 . Klj . 16 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...