belt FORD MUSTANG 2003 User Guide

„
A wobble or shudder. GO to Symptom Chart — Tire Noise/Vibration .
2. Depends more on where the vehicle is operated 1. Bump/pothole, rough road or smooth road. GO to Symptom Chart — Suspension
Noise/Vibration .
„ Noise is random or intermittent occurring from road irregularities. GO to Symptom Chart — Squeak and Rattle .
„ Noise or vibration changes from one road surface to another. Normal sound
changes.
„ Noise or vibration associated with a hard/firm ride. GO to Symptom Chart —
Suspension Noise/Vibration .
Symptom Charts Symptom Chart — Air Leak and Wind Noise Condition
Possible Sources Action
z Air leak around
door perimeter z
Loose fit seal. zPINCH the seal carrier to
improve retention on the
seal flange.
z Seal installed
incorrectly. z
REINSTALL the seal.
z Door misaligned. zREALIGN the door.
CHECK door gaps and fit
in the door opening and
ADJUST as necessary.
z Scuff plate installed
incorrectly. z
REINSTALL the scuff
plate.
z Seal or seal push pins
damaged. z
INSTALL a new seal.
z Air leak around
glass run z
Door glass misaligned. zADJUST the door glass.
z Glass run installed
incorrectly. z
ADJUST the glass run.
INSERT foam in the glass
run carrier.
z Leak path behind glass
run. z
INSTALL foam rope
behind the glass run.
z Glass run channel
spread wide. z
PINCH the glass run
channel to reduce the size
of the opening.
z Blow- out clip bent or
contacting door glass. z
ADJUST the blow- out clip
or INSTALL a new glass
run/blow- out clip molding
assembly.
z Glass run damaged. zINSTALL a new glass run.
z Air leak at inner
belt line z
Belt line seal installed
incorrectly on flange. z
ADJUST the seal. (Do not
bend the flange.)
z Belt line seal integrated
with door trim installed
incorrectly (no glass
contact). z
REINSTALL the door trim. Klj . 12 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
No contact with side
glass. z
ADJUST the door glass.
z No contact with glass
runs at both ends of
belt line seal. z
ADJUST the belt line seal
or ADD foam at the seal
ends.
z Belt line seal damaged. zINSTALL a new seal.
z Air leak at outer
belt line z
Belt line seal installed
incorrectly on flange
(no glass contact). z
ADJUST the seal.
z Belt line seal does not
contact the glass. z
ADJUST the door glass.
z No contact with glass
runs at both ends of
belt line seal. z
ADJUST the belt line
seal/ADD foam at the seal
ends.
z Belt line seal damaged. zINSTALL a new seal.
z Draft at inner
door
handle/speaker
opening z
Hole in watershield. zSEAL the hole with a
suitable tape.
z Watershield
misaligned. z
REALIGN the watershield.
INSTALL a new
watershield if the pressure
sensitive adhesive fails.
z Exterior door handle
seal
misaligned/damaged. z
REALIGN or INSTALL a
new seal as necessary.
z Wind noise from
side view mirror z
Outside mirror housing
misaligned. z
REALIGN with the edges
shingled correctly and no
gaps.
z Mirror sail gasket
folded/misaligned. z
REINSTALL with the
gasket unfolded and
aligned correctly.
z Mirror housing trim cap
installed incorrectly. z
REINSTALL with the
edges shingled to the air
flow.
z Air leak through mirror
housing hinge. z
Fully ENGAGE the mirror
into its operating
position/USE foam to
block the air path through
the hinge.
z Inner sail trim installed
incorrectly. z
REINSTALL the sail
trim/ADJUST the door
trim.
z Inner sail gasket/barrier
installed incorrectly. z
REINSTALL the trim
cover with the
gasket/barrier aligned
correctly.
z Air path through wiring
bundle/fastener access
holes. z
BLOCK the air path(s)
with foam/tape.
z Exposed fastener
access hole on mirror
housing/sail. z
INSTALL a new cap if it is
missing.
z Air leak around
perimeter of fixed z
Gaps in the sealant
bead. z
APPLY approved sealant. Klj . 13 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

CARRY OUT a driveline
vibration test. REFER to
Section 205
- 00 . REPAIR as
necessary.
z Binding or
damaged
splines on the
driveshaft slip-
yoke. z
CLEAN and INSPECT the
splines of the slip- yoke,
driveshaft and coupling
shaft for wear or damage.
INSTALL a new slip- yoke or
driveshaft assembly as
necessary. REFER to
Section 205 - 01 . REPAIR as
necessary.
z Driveshaft
runout. z
CARRY OUT a Runout
Check. REFER to Section 205 - 00 . REPAIR as
necessary.
z Incorrect lateral
and radial
tire/wheel
runout. z
INSPECT the tire and
wheels. MEASURE tire
runouts. REPAIR or
INSTALL new components
as necessary. REFER to
Section 204 - 04 .
z Driveline angles
out of
specification. z
CHECK for correct driveline
angles. REPAIR as
necessary. REFER to
Section 205 - 00 .
z Incorrectly
seated CV joint
in the front
wheel hub. z
CHECK the outer CV joint
for correct seating into the
hub. REPAIR as necessary. Symptom Chart —
Engine Noise/Vibration Condition
Possible Sources Action
z Grinding noise—
occurs during
engine cranking z
Incorrect starter
motor mounting. z
INSPECT the starter motor
for correct mounting.
REPAIR as necessary.
REFER to Section 303 - 06 .
z Starter motor. zCHECK the starter motor.
REPAIR or INSTALL a new
starter motor as necessary.
REFER to Section 303 - 06 .
z Incorrect starter
motor drive
engagement. z
INSPECT the starter motor
drive and flexplate/flywheel
for wear or damage.
INSTALL a new starter
motor drive or flywheel as
necessary. REFER to
Section 303 - 06 .
z Engine ticking
noise z
Fuel injector.
z Fuel line.
z Oil pump.
z Valve lifter.
z Belt tensioner.
z Water pump.
z Obstruction of cooling
fan. z
Go To Pinpoint Test B .
z Engine drumming zPowertrain mount. zCARRY OUT Klj . 23 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

noise—
normally
accompanied by
vibration Powertrain/Drivetrain Mount Neutralizing in this
section.
z Damaged or
misaligned exhaust
system. z
INSPECT the exhaust
system for loose or broken
clamps and brackets.
CARRY OUT Exhaust System Neutralizing in this
section.
z Whistling noise—
normally
accompanied
with poor idle
condition z
Air intake system. zCHECK the air intake
ducts, air cleaner, throttle
body and vacuum hoses for
leaks and correct fit.
REPAIR or ADJUST as
necessary. REFER to
Section 303 - 12
z
Clunking noise zWater pump has
excessive end play or
imbalance. z
CHECK the water pump for
excessive end play.
INSPECT the water pump
with the drive belt off for
imbalance. INSTALL a new
water pump as necessary.
REFER to Section 303 -
03A .
z Generator has
excessive end play. z
CHECK the generator for
excessive end play.
REPAIR or INSTALL a new
generator. REFER to
Section 414 - 02 .
z Pinging noise zExhaust system leak. zINSPECT the exhaust
system for leaks. REPAIR
as necessary.
z Gasoline octane too
low. z
VERIFY with customer the
type of gasoline used.
CORRECT as necessary.
z Knock sensor
operation. z
CHECK the knock sensor.
INSTALL a new knock
sensor as necessary.
REFER to Section 303 - 14 .
z Incorrect spark
timing. z
CHECK the spark timing.
REPAIR as necessary.
z High operating
temperature. z
INSPECT cooling system
for leaks. CHECK the
coolant level. REFILL as
necessary. CHECK the
coolant for the correct mix
ratio. DRAIN and REFILL
as needed. CHECK engine
operating temperature is
within specifications.
REPAIR as necessary.
z Foul- out spark plug. zCHECK the spark plugs.
REPAIR or INSTALL new
spark plugs as necessary.
z Catalytic converter. zAcceptable noise.
z Knocking noise—
light knocking
noise, also z
Excessive clearance
between the piston
and the cylinder wall. z
Engine cold and at high
idle. Using an EngineEAR,
pull a spark plug or fuel Klj . 24 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

as necessary.
z Accelerator pedal
vibration— felt
through the pedal
as a buzz z
Throttle cable loose
or misrouted. z
INSPECT the throttle cable.
REPAIR as necessary.
REFER to Section 310 - 02 .
z Engine
vibration— mostly
at coast/neutral
coast. Condition
improves with
vehicle
accelerating z
Combustion
instability. z
CHECK the ignition system.
INSTALL new components
as necessary.
z Engine vibration
or shudder—
occurs with light
to medium
acceleration
above 56 km/h
(35 mph) z
Worn or damaged
spark plugs. z
INSPECT the spark plugs
for cracks, high resistance
or broken insulator.
INSTALL a new spark plug
(s) as necessary.
z Plugged fuel injector. zREPAIR or INSTALL a new
injector as necessary.
REFER to Section 303 - 04A
for 3.8L engines or
Section 303 - 04B for 4.6L (2V)
engines.
z Damaged spark plug
wire. z
INSPECT the spark plug
wires for damage. INSTALL
a new spark plug wire(s) as
necessary.
z Contaminated fuel. zINSPECT the fuel for
contamination. DRAIN the
fuel system and refill.
z Worn or damaged
torque converter. z
CHECK the torque
converter. INSTALL a new
torque converter as
necessary. REFER to
Section 307 - 01 .
Symptom Chart—
Idle Noise/Vibration Condition
Possible Sources Action
z Idle air control (IAC)
valve moan — occurs
on throttle tip- out z
IAC valve is
contaminated
with oil. z
GO to Component Tests in
this section.
z Accessory drive belt
chirp — occurs at idle
or high idle, cold or
hot. Most common
occurrence is during
humid weather z
Accessory drive
belt worn, or
pulley is
misaligned or
loose. z
INSPECT for loose or
misaligned pulleys. CHECK
the drive belt for wear or
damage. INSTALL new
pulley(s)/drive belt, or
accessory drive components
as necessary. REFER to
Section 303 - 05 .
z Accessory drive
bearing hoot —
occurs at idle or high
idle in cold
temperatures of
approximately +4°C z
Accessory drive
idler or
tensioner pulley
bearing is
experiencing
stick/slip z
Go To Pinpoint Test C . Klj . 28 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

port. DISCARD the leaking
parts, and INSTALL a new
component.
z Vehicles with a
plastic intake
manifold. z
Acceptable condition. Some
plastic manifolds exhibit this
noise, which is the effect of
the plastic manifold.
z Automatic
transmission buzz or
hiss z
Incorrect
driveline
angles. z
CHECK for correct driveline
angles. REPAIR as
necessary. REFER to
Section 205 - 00 .
z Worn or
damaged main
control
solenoids or
valves. z
Using a transmission tester,
activate the solenoids to
duplicate sound. INSTALL
new components as
necessary. REFER to
Section 307 - 01 .
z Manual Transmission
Clutch throw- out
bearing whine. A
change in noise pitch
or loudness while
depressing the clutch
pedal z
Worn throw- out
bearing. z
INSTALL a new throw- out
bearing. REFER to Section 308 - 01 .
z Heating, vacuum and
air conditioning
(HVAC) system chirp
— most audible inside
the vehicle. Listen for
a change in noise
pitch or loudness
while changing the
HVAC system blower
speed z
Damaged or
worn HVAC
blower bearing. z
INSTALL a new blower
motor. REFER to Section 412 - 02 .
z Air conditioning (A/C)
clutch ticking —
occurs when the
compressor clutch
engages z
Acceptable
noise.
z Incorrect air
gap. z
LISTEN to the clutch to
determine if the noise occurs
with clutch engagement. A
small amount of noise is
acceptable. If the noise is
excessive, CHECK the A/C
clutch air gap. INSPECT the
A/C clutch for wear or
damage. INSTALL a new
clutch as necessary. REFER
to Section 412 - 03 .
z Intermittent rattle, or
scraping/rubbing
noise z
Loose exhaust
heat shield(s). z
INSPECT the exhaust
system for loose parts using
a glove or clamps to verify
cause. REPAIR as
necessary. REFER to
Section 309 - 00 .
z Wiring, hose or
other part
interfering with
accessory drive
belt or pulley. z
INSPECT accessory drive
system closely verifying
there is adequate clearance
to all rotating components.
REPAIR as necessary.
z Engine ticking or
knocking noise —
occurs during idle or z
Piston noise or
valvetrain noise
(bled down z
Go To Pinpoint Test G . Klj . 30 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

surfaces
zYoke spring in the
steering gear. z
CHECK TSBs for
revised yoke spring for
applicable vehicles.
z Accessory drive
belt squeal/chirp—
when rotating the
steering wheel
from stop to stop z
Loose or worn
accessory drive belt. z
ADJUST or INSTALL a
new accessory belt as
necessary. REFER to
Section 303 - 05 .
z Power steering
gear hiss z
Steering column
intermediate/flexible
shaft- to-steering gear
is binding or
misaligned. z
REPAIR or INSTALL a
new
intermediate/flexible
shaft as necessary.
REFER to Section 211 -
04 .
z Grounded or loose
steering column boot at
the dash panel. z
REPAIR as necessary.
z Damaged or worn
steering gear input
shaft and valve. z
REPAIR or INSTALL a
new steering gear as
necessary. REFER to
Section 211 - 02 .
z Steering column
rattle z
Loose bolts or
attaching brackets. z
TIGHTEN the bolts to
specifications.
z Loose, worn or
insufficiently lubricated
column bearings. z
LUBRICATE or
INSTALL new steering
column bearings as
necessary. REFER to
Section 211 - 04 .
z Steering shaft
insulators damaged or
worn. z
INSTALL new
insulators. REFER to
Section 211 - 04 .
z Intermediate/flexible
shaft compressed or
extended. z
INSPECT the rubber
spider coupling for
damage. INSTALL a
new
intermediate/flexible
shaft. REFER to Section 211 - 04 .
z Steering column
squeak or cracks z
Insufficient lubricated
steering shaft
bushings. z
LUBRICATE the
steering shaft and shaft
tube seals.
z Loose or misaligned
steering column
shrouds. z
TIGHTEN or ALIGN the
steering column
shrouds.
z Steering wheel rubbing
against steering
column shrouds. z
REPOSITION the
steering column
shrouds.
z Insufficient lubricated
speed control slip ring. z
LUBRICATE the speed
control slip ring.
z Upper or lower bearing
sleeve out of position. z
REPOSITION the
bearing sleeves.
z Power steering
pump noisy z
Incorrect assembly of
components.
z Imperfections on the
outside diameter or z
REPAIR or INSTALL a
new power steering
pump as necessary.
REFER to Section 211 -Klj . 35 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Is the ticking noise gone? CHECK for TSB for applicable vehicle.
REPAIR as necessary. TEST the system
for normal operation.
No
GO to
B2 .
B2 CHECK FOR TICKING NOISE AT THE FUEL
INJECTOR z
Using an EngineEAR, listen at the fuel
injectors by placing a probe on each injector.
To isolate the faulty injector, disconnect the
injector electrical connector and listen for the
noise.
z Is the fuel injector the source of the ticking
noise? Yes
INSTALL a new fuel injector. REFER to
Section 303
- 04A for 3.8L engines or
Section 303 - 04B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B3 .
B3 CHECK THE BELT TENSIONER FOR TICKING
NOISE z
Inspect the accessory drive. Check for the belt
tensioner bottoming at end of travel or not at
end of stroke.
z Using an EngineEAR, listen at the belt
tensioner.
z Is the belt tensioner the source of the
noise? Yes
INSTALL a new belt tensioner. TEST the
system for normal operation.
No
GO to
B4 .
B4 CHECK THE WATER PUMP FOR TICKING
NOISE z
Using an EngineEAR, listen at the water pump
for ticking noise.
z Is the water pump the source of the noise? Yes
INSTALL a new water pump. REFER to
Section 303
- 03A . TEST the system for
normal operation.
No
GO to B5 .
B5 CHECK FOR AN OBSTRUCTION OF THE
COOLING FAN z
Inspect the cooling fan for obstructions.
z Check the cooling fan and shroud for wear or
damage.
z Was there an obstruction or does the
cooling fan show signs of damage? Yes
REPAIR or INSTALL a new cooling fan.
REFER to
Section 303 - 03A . TEST the
system for normal operation.
No
GO to B6 .
B6 CHECK THE OIL PUMP FOR TICKING NOISE
z
Check the oil pump using EngineEARs and
probe at the oil filter adapter to verify the oil
pump as a source.
z Is the oil pump the source of the noise? Yes
INSTALL a new oil pump. REFER to
Section 303
- 01A for 3.8L engines or
Section 303 - 01B for 4.6L (2V) engines.
TEST the system for normal operation.
No
GO to B7 .
B7 CHECK VALVE LIFTERS OR LASH
ADJUSTERS FOR CORRECT OPERATION z
Check valve lifter/lash adjuster for correct
operation, using EngineEARs.
z Are the valve lifters/lash adjusters Yes
VERIFY customer concern. CONDUCT a
diagnosis of other suspect components. Klj . 50 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST L: CLUTCH VIBRATION appropriate workshop manual for the service procedures.
z Secure the brake drums (if so equipped), by installing wheel
hub bolt nuts, reversed.
z Carefully accelerate the drivetrain while checking for vibration.
z Is the vibration present? assemblies as necessary.
TEST the system for
normal operation.
Test Step Result / Action to Take
L1 CHECK ENGINE COMPONENTS FOR GROUNDING
z
NOTE: Make sure the clutch is the cause of the
vibration concern. The vibration should occur during
clutch operation. The clutch can also be difficult to
engage or disengage. Eliminate all related systems
before checking the clutch components.
z NOTE: Check the driveline angles and driveshaft
runout before disassembling the clutch system. Refer
to Section 205 - 00 for the correct driveline angle
specifications.
z Check the powertrain/drivetrain mounts, exhaust
manifolds or other engine components for grounding
on the chassis.
z Are any mounts or engine components
grounded? Yes
REPAIR as necessary. TEST the
system for normal operation.
No
GO to
L2 .
L2 CHECK THE ACCESSORY DRIVE
z
Remove the accessory drive belt.
z Does the vibration stop with the accessory drive
belt removed? Yes
DIAGNOSE the accessory drive
components.
No
GO to
L3 .
L3 CHECK FOR LOOSE CLUTCH PRESSURE PLATE
BOLTS z
Check for loose clutch pressure plate bolts. Inspect
the clutch pressure plate for damage or for material
between the pressure plate and flywheel.
z Are there any loose bolts or damage? Yes
TIGHTEN the bolts to
specifications or if damaged,
INSTALL a new clutch pressure
plate. REFER to
Section 308 - 01 .
TEST the system for normal
operation.
No
GO to L4 .
L4 CHECK THE CLUTCH DISC SPRINGS
z
Check for worn, broken or loose clutch disc springs.
z Are the clutch springs worn, broken or loose? Yes
INSTALL a new clutch disc.
REFER to
Section 308 - 01 . TEST
the system for normal operation.
No
GO to L5 .
L5 CHECK THE CLUTCH DISC SPLINES
z
Inspect the clutch disc splines for damage or wear.
z Is there damage or wear? Yes
INSTALL a new clutch disc.
REFER to
Section 308 - 01 . TEST Klj . 61 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Wheels And Tires
WARNING: Do not mix different types of tires, such as radial, bias, or bias- belted, on the
same vehicle except in emergencies. Vehicle handling can be seriously affected and can result
in loss of control.
Factory-installed tires and wheels are designed to operate satisfactorily with loads up to and including
full- rated load capacity when inflated to recommended inflation pressures.
Tire and Wheel Runout
Excessive radial and lateral runout of a wheel and tire assembly can cause roughness, vibration,
wheel tramp, tire wear, and steering wheel tremor.
Before checking runout, and to avoid false readings caused by temporary flat spots in the tires, check
runout only after the vehicle has been driven far enough to warm the tires. For additional information,
refer to Section 100 - 04 .
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...