rear view mirror FORD MUSTANG 2003 User Guide

z
Is the circuit logic OK? Circuit position resistance
Passenger
543
(DG) Left Greater than 10 volts
543
(DG) Right Less than 5 ohms
544
(VT) Up Greater than 10 volts
544
(VT) Down Less than 5 ohms
542
(YE) Left Less than 5 ohms
542
(YE) Right Greater than 10 volts
542
(YE) Up Less than 5 ohms
542
(YE) Down Greater than 10 volts
C2 CHECK THE EXTERIOR REAR VIEW MIRROR
CONTROL z
Remove the exterior rear view mirror control. Leave the
harness connected.
z Measure for voltage or resistance at exterior rear view
mirror control C527 while actuating the exterior rear view
mirror control according to the following chart. Pin Circuit Exterior rear view
mirror control position Measure for
resistance or voltage 6 542
(YE) Left Less than 5 ohms
6 542
(YE) Right Greater than 10
volts 6 542
(YE) Up Less than 5 ohms
6 542
(YE) Down Greater than 10
volts Driver side selected
4 540
(RD) Left Greater than 10
volts 4 540
(RD) Right Less than 5 ohms
3 541
(DB) Up Greater than 10
volts 3 541
(DB) Down Less than 5 ohms
Passenger side selected
8 543 Left Greater than 10 Yes
REPAIR the circuits. TEST the
system for normal operation.
No
INSTALL a new exterior rear
view mirror control. REFER to
Switch
— Exterior Rear View
Mirror Control in this section.
TEST the system for normal
operation. Klj . 7 ba
82003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Mirror —Power Exterior Rear View
Removal
1. Remove the door trim panel. For additional information, refer to Section 501 - 05 .
2. Disconnect the power exterior rear view mirror electrical connector.
3. Remove the nuts and the power exterior rear view mirror.
Installation 1. To install, reverse the removal procedure.
SECTION 501-
09: Rear View Mirrors 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Mirror —Motor
Removal
1. Push in the upper edge of the mirror glass to the maximum travel.
2. Grasp the bottom of the mirror glass, pull outward and remove the mirror glass.
3. Remove the mirror motor screws.
4. Disconnect the mirror motor electrical connector.
5. Remove the mirror motor.
Installation 1. NOTE: When installing the mirror glass, make sure it snaps completely into the mirror motor.
SECTION 501-
09: Rear View Mirrors 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Switch —
Exterior Rear View Mirror Control
Removal
1. CAUTION: Use a shop towel or similar material between the tool and the front door
trim panel or damage to the front door trim panel may occur.
Position the window regulator switch plate aside. 1. Pull at service notch.
2. Lift to release the clip at the rear edge.
2. Remove the power exterior rear view mirror control switch. zDisconnect the electrical connector.
Installation 1. To install, reverse the removal procedure.
SECTION 501-
09: Rear View Mirrors 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Windshield Glass
Removal
All vehicles
WARNING: To prevent glass splinters from entering eyes or cutting hands, wear safety
glasses and heavy gloves when cutting glass from the vehicle.
1. Remove the RH and LH windshield side garnish mouldings. zIf equipped with a convertible top, remove the pin- type retainers.
2. Remove the interior rear view mirror.
Convertible
3. Remove the visor trim moulding.
SECTION 501-
11: Glass, Frames and Mechanisms 2003 Mustang Workshop Manual Special Tool(s)
Rotunda Pneumatic Knife with
Offset Blade
107-
R1511 or equivalent The Pumper
164-
R2459 or equivalent Rotunda Interior Auto Glass
Cut-
Out Knife Kit
164- R2450 or equivalent Klj . 1 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Connect the electrical connector(s).
22. Install the visor trim moulding.
All vehicles 23. Install the RH and LH windshield side garnish moulding. zIf equipped with a convertible top, install the pin- type retainers.
24. Install the interior rear view mirror. Klj . 9 ba
102003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...