FORD MUSTANG 2003 Workshop Manual

IN-
VEHICLE REPAIR
Reverse Servo Assembly
Removal 1. Remove the main control valve body. For additional information, refer to Main Control Valve Body in this section.
2. Using the special tool, remove the reverse band servo retaining ring. 1. Compress the servo spring.
2. Remove the reverse band servo retaining ring.
3. Remove the reverse servo assembly. 1. Remove the reverse band servo cover.
2. Remove the reverse band servo piston and rod.
3. Remove the reverse band servo spring.
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Special Tool(s)
Dial Indicator Gauge with
Holding Fixture
100-
002 (TOOL- 4201-C) Remover/Installer, Servo
Piston
307-
251 (T92P-70023- A) Installer, Servo Piston
307-
073 (T80L-77030- A) Klj . 1 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Installation
NOTE:
This is not an ordinary installation procedure and does not compensate for band wear.
1. NOTE: Lubricate the reverse piston seal to facilitate assembly and prevent damage to the seal.
Install the reverse servo return spring and piston. zDo not install the piston cover.
2. Install the special tool and tighten the band apply bolt.
3. Attach the special tool to the transmission. zPosition the indicator stem on the flat portion of the reverse servo piston and zero the dial
indicator. Klj . 2 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

4. Loosen the bolt until the piston stops against the tool.
5. Verify that the amount of piston travel on the dial indicator is within specification.
6. If piston travel is not within specification, select and install the correct servo piston assembly to
bring the servo piston travel within specification. 1. One groove
2. Two groove
3. Three groove
7. Remove the dial indicator and servo selection tool. Klj . 3 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

8. Install the correct reverse servo assembly.
1. Install the reverse band servo spring.
2. Install the reverse band servo piston and rod.
3. Install the reverse band servo cover.
9. Using the special tool, install the reverse servo retaining ring. 1. Compress the servo spring.
2. Install the reverse band servo retaining ring.
10. Install the main control valve body. For additional information, refer to Main Control Valve Body in this section. Klj . 4 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Klj . 5 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Overdrive Servo
Removal 1. Remove the main control valve body. For additional information, refer to Main Control Valve Body in this section.
2. NOTE: If the tool is not available, extreme care must be taken. Spring pressure will force
overdrive servo piston assembly out of case. Case bore damage may result from trying to pry
on overdrive servo internal retaining ring.
Using the special tool, compress the servo spring to remove the overdrive servo retaining ring.
3. Remove the overdrive servo piston and return spring.
Installation 1. Install the overdrive servo piston assembly. 1. Install the overdrive servo piston return spring.
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Special Tool(s)
Remover/Installer, Servo
Piston
307-
251 (T92P-70023- A) Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

2. Install the overdrive servo piston assembly.
2. Use the special tool to install the overdrive servo piston retaining ring.
3. Install the main control valve body. For additional information, refer to Main Control Valve Body in this section. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

IN-
VEHICLE REPAIR
1- 2 Accumulator
Removal 1. Compress the 1- 2 accumulator cover and remove the accumulator piston retaining ring.
2. NOTE: Note the location of the 1- 2 accumulator springs for reference during assembly.
Remove the 1- 2 accumulator.
1. Remove the 1- 2 accumulator cover.
2. Remove the lower 1- 2 accumulator spring.
3. Remove the accumulator piston.
4. Remove the upper 1- 2 accumulator spring.
Installation 1. Install the 1- 2 accumulator.
1. Install the 1- 2 accumulator upper spring.
2. Install the accumulator piston.
3. Install the 1- 2 accumulator lower spring. 4. Install the cover and seal assembly. SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

2. Compress the accumulator and install the accumulator piston retaining ring. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

IN-
VEHICLE REPAIR
2- 3 Accumulator
Removal 1. Remove the main control valve body. For additional information, refer to Main Control Valve Body in this section.
2. Remove the 2- 3 accumulator piston retainer.
3. Remove the accumulator piston and spring.
Installation 1. Install the 2- 3 accumulator assembly.
1. Install the accumulator piston.
2. Install the accumulator piston spring.
3. Install the accumulator spring retainer.
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...