FORD MUSTANG 2003 Workshop Manual

9 7N232 Gear shift plate
10 7K201 Gear selector interlock sleeve
11 305078-
S Pin
12 7302 Selector body
13 7230 Gear shifter fork 3-
4 shift 14 7160 Output shaft bearing snap ring
15 7117 Second speed synchronizer thrust washer
16 7175 First and second gear synchronizer inner cone
17 7174 First and second gear synchronizer outer cone
18 7107 Synchronizer blocking ring
19 7A044 Synchronizer hub insert (also part of 7124)
20 7K218 First and second speed synchronizer hub ball
21 7061 Output shaft assembly
22 7109 Synchronizer hub insert spring (also part of
7124)
23 7124 Sleeve (also part of 7061)
24 7173 First gear bearing spacer
25 7127 First gear bearing
26 7100 First gear
27 7065 Output shaft rear bearing
28 7D234 Thrust bearing
29 7D235 Thrust washer
30 — Synchronizer hub (part of 7124)
31 7124 Synchronizer assembly
32 7B340 Third gear
33 7B369 Third speed bearing
34 7B320 Third speed gear bearing spacer
35 7064 Snap ring
36 7119 Thrust washer
37 7102 Second gear
38 7728 Second speed gear bearing spacer
39 7693 Countershaft front bearing seal
40 7F431 Countershaft bearing assembly
41 7113 Countershaft cluster gear
42 7L172 Countershaft rear bearing adjustment shim
43 7195 Countershaft rear bearing retainer
44 7C210 Bolt
45 7144 Fifth speed cluster gear
46 7M000 Reverse brake ring
47 7G042 Thrust washer
48 7059 Fifth speed synchronizer retaining snap ring
49 7L276 Oil pick-
up funnel Klj . 3 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

Transmission Identification
The transmission identification tag is located under the lower left bolt that retains the extension 50 7230 Reverse shift fork
51 7240 Reverse gear shift rail
52 7230 Fifth gear shifter fork
53 357479-S15 Split pin
54 371197-
S Reverse gearshift lever retaining clip
55 7K002 Reverse gearshift lever
56 7E485 Reverse positioning spring
57 7005 Case
58 87675-
S Case plug
59 74113-
S Plug
60 15520 Reversing lamp switch
61 7K024 Shift lever reverse pin
62 7E397 Reverse gear overtravel stop
63 7141 Reverse idler gear and bushing
64 7140 Reverse idler gear shaft
65 357479-S15 Pin
66 7K316 Fifth speed driven gear
67 7H150 Output shaft speed wheel
68 7034 Vent
69 E800152-S72 Bolt
70 7A039 Extension housing
71 7K381 Extension plug
72 7052 Extension housing fluid seal
73 372720-
S Detent ball
74 7234 Shifter detent spring
75 7F018 Gearshift offset lever
76 7K453 Gearshift shaft bushing
77 7A443 Bolt
78 7C108 Gearshift lower boot clamp
79 7210 Gearshift lever
80 7277 Gearshift lever boot
81 N602187-
S100 Bolt
82 7050 Input shaft bearing retainer
83 7052 Input shaft seal
84 7025 Input bearing assembly
85 7017 Input shaft
86 7118 Roller bearing (15 req'd)
87 7L357 Input shaft bearing spacer Klj . 4 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

housing (7A039) to the case (7005).
Transmission Identification Tag
Item Part
Number Description
1 — Transmission assembly number
2 — Build date code—
month 3 — Build date code—
day 4 — Build date code—
year 5 — Shift Number
6 — Serial number
7 — Wg. identification number (Located on the extension
housing bolt on the LH side of the transmission) Klj . 5 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Manual Transmission
Refer to
Section 308 - 00 .
SECTION 308-
03A: Manual Transaxle/Transmission — T5OD 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Seal
Removal 1. With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. CAUTION: Index- mark the driveshaft flange and pinion flange, and the driveshaft
slip yoke and transmission output shaft.
Remove the driveshaft. For additional information, refer to Section 205 - 01 .
3. Using the special tools, remove the extension housing fluid seal.
Installation 1. Using the special tool, install the extension housing fluid seal.
SECTION 308-
03A: Manual Transaxle/Transmission — T5OD 2003 Mustang Workshop Manual Special Tool(s)
Installer, Transmission
Extension Housing Oil Seal
308-
227 (T94P-7657- A) Slide Hammer
100-
001 (T50T-100- A) Remover, Bushing
307-
001 (TOOL- 1175-AC) or
Equivalent Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

2.
CAUTION: Align the index marks.
Install the driveshaft. For additional information, refer to Section 205 - 01 .
3. Check the transmission fluid level, add fluid if necessary.
4. Lower the vehicle. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Gearshift Lever and Boot
Removal and Installation 1. Remove the gearshift lever knob.
2. Remove the console panel gearshift plate. Lift the gearshift lever boot over the gearshift lever.
3. Remove the bolts and the shift lever.
SECTION 308-
03A: Manual Transaxle/Transmission — T5OD 2003 Mustang Workshop Manual Material
Item Specification
Clear Silicone Rubber
D6AZ-
19562- AA or equivalent ESB-
M4G92- A Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

4. Remove the screws and the inner shifter boot.
5. Remove the bolts and the gearshift lever.
6. Remove the gearshift lever boot.
7.
CAUTION: Cover the opening in the extension housing to prevent contamination.
Clean the gearshift lever mounting surfaces.
8. To install, reverse the removal procedure. zApply a 3.2- mm (1/8-in) bead of silicone rubber to the sealing surface on the gearshift
lever. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

Klj . 3 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Output Shaft Speed (OSS) Sensor
Removal and Installation 1. With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. Disconnect the electrical connector.
3. Remove the output shaft speed (OSS) sensor.
4. To install, reverse the removal procedure.
SECTION 308-
03A: Manual Transaxle/Transmission — T5OD 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...