oil level FORD MUSTANG 2003 Owner's Manual

z
intake manifold gaskets
z cylinder head gaskets
z oil bypass filter
z oil filter adapter
z engine front cover
z oil filter adapter and filter body
z oil level indicator tube connection
z oil pressure sensor
Leakage Points— Under Engine—With Vehicle on Hoist
z oil pan gaskets (6710)
z oil pan sealer
z oil pan rear seal (6723)
z engine front cover gasket
z crankshaft front seal (6700)
z crankshaft rear oil seal (6701)
z crankshaft main bearing cap side bolts
z oil filter adapter and filter body
z oil cooler, if equipped
Leakage Points— With Transmission and Flywheel Removed
z crankshaft rear oil seal
z rear main bearing cap parting line
z rear main bearing cap and seals
z flywheel mounting bolt holes (with flywheel [6375] installed)
z camshaft rear bearing covers (6266) or pipe plugs at the end of oil passages
Oil leaks at crimped seams in sheet metal parts and cracks in cast or stamped parts can be detected
when using the dye method.
Compression Test— Compression Gauge Check
1. Make sure the oil in the crankcase is of the correct viscosity and at the correct level and that the battery (10655) is correctly charged. Operate the vehicle until the engine is at normal operating
temperature. Turn the ignition switch to the OFF position, then remove all the spark plugs
(12405).
2. Set the throttle plates in the wide- open position.
3. Install a compression gauge such as the Compression Tester in the No. 1 cylinder.
4. Install an auxiliary starter switch in the starting circuit. With the ignition switch in the OFF position, and using the auxiliary starter switch, crank the engine a minimum of five compression
strokes and record the highest reading. Note the approximate number of compression strokes Klj . 7 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. If compression improves considerably, piston rings are faulty.
2. If compression does not improve, valves are sticking or seating incorrectly.
3. If two adjacent cylinders indicate low compression pressures and squirting oil on each piston
does not increase compression, the head gasket may be leaking between cylinders. Engine oil
or coolant in cylinders could result from this condition.
Use the Compression Pressure Limit Chart when checking cylinder compression so that the
lowest reading is within 75 percent of the highest reading.
Cylinder Leakage Detection
When a cylinder produces a low reading, use of the Engine Cylinder Leak Detection/Air Pressurization
Kit will be helpful in pinpointing the exact cause.
The leakage detector is inserted in the spark plug hole, the piston is brought up to dead center on the
compression stroke, and compressed air is admitted.
Once the combustion chamber is pressurized, a special gauge included in the kit will read the
percentage of leakage. Leakage exceeding 20 percent is excessive.
While the air pressure is retained in the cylinder, listen for the hiss of escaping air. A leak at the intake
valve (6507) will be heard in the throttle body (9E926). A leak at the exhaust valve (6505) can be
heard at the tail pipe. Leakage past the piston rings will be audible at the positive crankcase ventilation
(PCV) connection. If air is passing through a blown head gasket to an adjacent cylinder, the noise will
be evident at the spark plug hole of the cylinder into which the air is leaking. Cracks in the cylinder
block or gasket leakage into the cooling system may be detected by a stream of bubbles in the radiator
(8005).
Oil Consumption Test
The following diagnostic procedure is used to determine the source of excessive internal oil
consumption. 1. NOTE: Oil use is normally greater during the first 16,100 km (10,000 miles) of service. As
mileage increases, oil use generally decreases. Vehicles in normal service should get at least
1,450 km per liter (900 miles per quart) after 16,000 km (10,000 miles) of service. High speed
driving, towing, high ambient temperature and other factors may result in greater oil use.
Define excessive oil consumption, such as the number of miles driven per liter (quart) of oil
used. Also determine customer's driving habits, such as sustained high speed operation,
towing, extended idle and other considerations.
2. Verify that the engine has no external oil leak as described under Engine Oil Leaks in the Diagnosis and Testing portion of this section.
3. Verify that the engine has the correct oil level dipstick (6750).
4. Verify that the engine is not being run in an overfilled condition. Check the oil level at least five minutes after a hot shutdown with the vehicle parked on a level surface. In no case should the
level be above MAX or the letter F in FULL. If significantly overfilled, carry out Steps 6a through
6d.
5. Verify the spark plugs are not oil saturated. If the spark plugs are oil saturated and compression is good it can be assumed the valve seals or valve guides are at fault. Klj . 9 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Carry out an oil consumption test:
a. Drain the engine oil, remove the oil bypass filter (6714) and refill with one liter (quart) less than
the recommended amount.
b. Run the engine for three minutes (10 minutes if cold), and allow the oil to drain back for at least five minutes with the vehicle on a level surface.
c. Remove oil level dipstick and wipe clean. (Do not wipe with anything contaminated with silicone compounds.) Reinstall the oil level dipstick, being sure to seat it firmly in the oil level indicator
tube (6754). Remove the oil level dipstick and draw a mark on the back (unmarked) surface at
the indicated oil level. This level should be about the same as the MIN or ADD mark on the face
of the oil level dipstick.
d. Add one liter (quart) of oil. Restart the engine and allow to idle for at least two minutes. Shut off the engine and allow the oil to drain back for at least five minutes. Mark the oil level dipstick,
using the procedure above.
e. Record the vehicle mileage. f. Instruct the customer to drive the vehicle as usual and perform the following:
„Check the oil level regularly at intervals of 160 to 240 km (100- 150 miles).
„ Return to the service point when the oil level drops below the lower (MIN or ADD) mark
on the oil level dipstick.
„ Add only full liters (quarts) of the same oil in an emergency. Note the mileage at which
the oil is added.
g. Check the oil level under the same conditions and at the same location as in Steps 6c and 6d.
„Measure the distance from the oil level to the UPPER mark on the oil level dipstick and
record.
„ Measure the distance between the two scribe marks and record.
„ Divide the first measurement by the second.
„ Divide the distance driven during the oil test by the result. This quantity is the
approximate oil consumption rate in kilometers per liter or in miles per quart.
h. If the oil consumption rate is unacceptable, go to Step 7.
7. Check the positive crankcase ventilation (PCV) system. Make sure the system is not plugged.
8. Check for plugged oil drain- back holes in the cylinder heads and cylinder block.
9. If the condition still exists after performing the above steps, go to Step 10.
10. Perform a cylinder compression test or perform a cylinder leak detection test with Engine Cylinder Leak Detection/Air Pressurization Kit. This can help determine the source of oil
consumption such as valves, piston rings or other areas.
11. NOTE: After determining if new parts should be installed, make sure correct parts are used.
Check valve guides for excessive guide clearance. Install new all valve stem seals (6571) after
verifying valve guide clearance.
12. Worn or damaged internal engine components can cause excessive oil consumption. Small deposits of oil on the tips of spark plugs can be a clue to internal oil consumption. If internal oil
consumption still persists, proceed as follows:
a. Remove the engine from the vehicle and place it on an engine work stand. Remove the intake manifolds (9424), cylinder heads, oil pan (6675) and oil pump (6600).
b. Check piston ring clearance, ring gap and ring orientation. Repair as necessary.
c. Check for excessive bearing clearance. Repair as necessary.
13. Repeat the oil consumption test (Step 6) to confirm the oil consumption concern has been resolved. Klj . 10 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Engines need oil to lubricate the following internal components:
zcylinder block cylinder walls
z pistons and piston, pin and rings (6102)
z intake and exhaust valve stems
z intake and exhaust valve guides
z all internal engine components
When the pistons move downward, a thin film of oil is left on the cylinder walls. As the vehicle is
operated, some oil is also drawn into the combustion chambers past the intake and exhaust valve
stem seals and burned.
The following is a partial list of conditions that can affect oil consumption rates:
zengine duty cycle
z operator driving habits
z ambient temperature
z quality and viscosity of the oil
Operation under varying conditions can frequently be misleading. A vehicle that has been run for
several thousand miles on short trips or in below- freezing ambient temperatures may have consumed
a "normal" amount of oil. However, when checking the engine oil level, it may measure up to the FULL
or MAX on the oil level dipstick due to dilution (condensation and fuel) in the engine crankcase. The
vehicle might then be driven at high speeds on the highway where the condensation and fuel boil off.
The next time the engine oil is checked, it may appear that a liter (quart) of oil was used in about 160
km (100 miles). This perceived 160 km (100 miles) per liter (quart) oil consumption rate causes
customer concern even though the actual overall oil consumption rate is about 2,400 km (1,500 miles)
per liter (quart).
Make sure the selected engine oil meets the current recommended API performance category with
SAE viscosity grade as shown in the vehicle Owner's Guide. It is also important that the engine oil is
changed at the intervals specified. Refer to the vehicle Owner's Guide.
Oil Pressure Test
1. Disconnect and remove the oil pressure sensor (9278) from the engine.
2. Connect the Oil Pressure Gauge to the oil pressure sender oil galley port.
3. Run the engine until normal operating temperature is reached.
4. Run the engine at the specified rpm and record the gauge reading.
5. The oil pressure should be within specifications; refer to the specification chart in the appropriate engine section.
6. If the pressure is not within specification, check the following possible sources: zinsufficient oil
z oil leakage
z worn or damaged oil pump
z oil pump screen cover and tube (6622)
z excessive main bearing clearance Klj . 13 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
incorrectly functioning valve tappet
z air in lubrication system
z excessive valve guide wear
z low oil pressure
Excessive collapsed valve tappet gap can be caused by loose rocker arm seat bolts/nuts, incorrect
initial adjustment or wear of valve tappet face, or worn roller valve tappets, push rod (6565), rocker
arm (6564), rocker arm seat or valve tip. With valve tappet collapsed, check gap between the valve tip
and the rocker arm to determine if any other valve train parts are damaged, worn or out of adjustment.
An incorrectly functioning valve tappet can be sticking, caused by contaminants or varnish inside the
tappet. The tappet can have a check valve that is not functioning correctly, which can be caused by an
obstruction, such as dirt or chips that prevent the check valve from closing, or a broken check valve
spring. A tappet with a leakdown time out of specification can cause tappet noise. If no other cause for
noisy valve tappets can be found, the leakdown rate should be checked and new valve tappets
installed if found to be out of specification.
Assembled valve tappets can be tested with Hydraulic Tappet Leakdown Tester to check the leakdown
rate. The leakdown rate specification is the time in seconds for the plunger to move a specified
distance while under a 22.7 kg (50 lb) load.
Air bubbles in the lubrication system will prevent the valve tappet from supporting the valve spring
load. This can be caused by too high or too low an oil level in the oil pan or by air being drawn into the
system through a hole, crack or leaking gasket on the oil pump screen cover and tube. Klj . 17 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

A/C compressor bracket-
to-cylinder head stud bolt 25 18 —
Oil level indicator tube-
to-cylinder head bolt 10 — 89
Coolant recovery reservoir bracket-to-
GOP bolts 9 — 80
Motor mount-
to-subframe nuts 115 85 —
Oil pan drain plug 26 19 —
Wire harness bracket to motor mount nut 27 20 —
Steering column pinch bolt 47 35 —
Front subframe-
to-body bolts 90 66 —
Front subframe-
to-shock tower bolts 115 85 —
Oil pan-to-
cylinder block bolts a — — —
Oil pan-to-
transmission bell housing 45 33 —
Main bearing bridge nuts 32 24
Oil pump cover-
to-engine front cover bolts 25 18 —
Oil pump cover-
to-engine front cover bolt 10 89 —
Oil pickup tube-
to-cylinder block bolts 25 18 —
Oil pickup tube-
to-oil pan baffle nut 48 35 —
Flywheel-
to-crankshaft bolts 80 59 —
Wire harness bracket-
to-motor mount stud- nut 27 20 —
Engine ground strap-
to-motor mount nut 27 20 —
Motor mount-
to-motor mount bracket bolts 70 52 —
RH motor mount-
to-motor mount bracket nut 70 52 —
Hood ground strap-
to-hood hinge bolt 12 9 —
Hood hinge nuts 12 9 —
Generator mounting bracket 25 18 —
Power steering pump bracket nuts 8 — 71
Power steering pump bolts 25 18 —
Valve tappet guide plate bolts 12 9 —
Generator positive cable nut 10 — 89
Power steering pressure tube to pump nut 40 30 —
Accelerator cable bracket-
to-intake manifold bolts 10 — 89
42-
pin connector bolt 10 — 89
Transmission oil cooler tube bracket-
to-motor mount bracket nut 27 20
Torque converter-
to-flywheel nuts 36 27 —
Engine-
to-transmission bolts 40 30 —
Engine mount bracket-
to-engine bolts 70 52 —
Engine mount bracket-
to-engine nuts 70 52 —
Water pump pulley bolts 25 18 —
Oil filter
b — — —
Upper intake manifold-
to-lower intake manifold bolts a — — —
Lower intake manifold-
to-cylinder head bolts a — — —
Rocker arm pivot-
to-cylinder head bolts a — — — Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Engine Front Cover Components 9 6A666 Positive crankcase ventilation valve
10 6565 Push rod
11 6564 Rocker arm
12 6A528 Rocker arm seat
13 N807699 Bolt
14 6518 Valve spring retainer key
15 6514 Valve spring retainer
16 6513 Valve spring
17 6A517 Valve stem seal
18 611497 Bolt
19 6049 Cylinder head —
LH 20 9448 Exhaust manifold gasket —
LH 21 17A084 Engine lifting eye
22 6754 Oil level indicator tube
23 9430 Exhaust manifold —
LH 24 6507 Intake valve
25 6505 Exhaust valve
26 6051 Head gasket —
LH 27 6051 Head gasket —
RH 28 9448 Exhaust manifold gasket —
RH 29 9430 Exhaust manifold —
RH 30 17A084 Engine lifting eye Klj . 2 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Oil Level Indicator and Tube
Removal and Installation 1. Remove the oil level indicator tube (6754). zRemove the bolt.
z Remove the oil level indicator tube.
z Remove and discard the oil level indicator tube O- ring.
2. To install, reverse the removal procedure.
SECTION 303-
01A: Engine — 3.8L 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Remove the bolts and the RH engine support insulator.
3. Remove the special tool.
4. Remove the special tool.
5. Remove the bolt and the oil level indicator and tube. Discard the O-
ring. Klj . 2 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

78. Install the exhaust gas recirculation (EGR) tube.
79. Connect the EGR valve nut.
80. Using a new gasket, install the LH exhaust manifold. Tighten the nuts in the sequence shown.
81.
NOTE: Install a new O- ring seal.
Install the oil level indicator and tube and retaining bolt. Klj . 25 ba
282003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...