brake FORD MUSTANG 2003 Workshop Manual

z
Was the result retrieved ABS: NO RESPONSE ON
CKT914 (BUS+)? A3 CHECK FOR OPEN BETWEEN DLC C251 AND ANTI-
LOCK BRAKE CONTROL MODULE C135 — CIRCUIT 914
(TN/OG) z
Key in OFF position.
z Disconnect the diagnostic tool.
z Disconnect: Anti- Lock Brake Control Module C135.
z Measure the resistance between anti- lock brake control
module C135 Pin 30, Circuit 914 (TN/OG), harness side
and DLC C251 Pin 2, Circuit 914 (TN/OG), harness
side.
z Is the resistance less than 5 ohms? Yes
INSTALL a new anti-
lock brake
control module. REFER to
Section 206 - 09B . TEST the
system for normal operation.
No
GO to A4 .
A4 CHECK CIRCUIT 914 (TN/OG) BETWEEN DLC C251
AND IN- LINE C144 FOR OPEN z
Disconnect: In- Line C144.
z Check in-line C144 for damage; repair as necessary.
z Measure the resistance between in- line C144 Pin 6,
Circuit 914 (TN/OG), harness side and DLC C251 Pin 2,
Circuit 914 (TN/OG), harness side.
z Is the resistance less than 5 ohms? Yes
REPAIR Circuit 914 (TN/OG)
between anti-
lock brake control
module C135 and in- line C144.
For additional information,
REFER to Communication Circuit Wiring Repair . TEST the
system for normal operation.
No
GO to A5 .
A5 CHECK CIRCUIT 914 (TN/OG) BETWEEN DLC C251
AND IN- LINE C215 FOR OPEN z
Disconnect: In- Line C215.
z Check in-line C215 for damage; repair as necessary.
z Measure the resistance between in- line C215 Pin 10,
Circuit 914 (TN/OG), harness side and DLC C251 Pin 2,
Circuit 914 (TN/OG), harness side. Yes
REPAIR Circuit 914 (TN/OG)
between in-
line C144 and in- line
C215. For additional
information, REFER to
Communication Circuit Wiring Repair . TEST the system for
normal operation.
No
REPAIR Circuit 914 (TN/OG)
between DLC C251 and in- line
C215. For additional Klj . 5 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the resistance less than 5 ohms? information, REFER to
Communication Circuit Wiring
Repair . TEST the system for
normal operation. A6 CHECK FOR OPEN BETWEEN DLC C251 AND ANTI-
LOCK BRAKE CONTROL MODULE C135 — CIRCUIT 915
(PK/LB) z
Key in OFF position.
z Disconnect the diagnostic tool.
z Measure the resistance between anti- lock brake control
module C135 Pin 29, Circuit 915 (PK/LB), harness side
and DLC C251 Pin 10, Circuit 915 (PK/LB), harness
side.
z Is the resistance less than 5 ohms? Yes
INSTALL a new anti-
lock brake
control module. REFER to
Section 206 - 09B . TEST the
system for normal operation.
No
GO to A7 .
A7 CHECK CIRCUIT 915 (PK/LB) BETWEEN DLC C251
AND IN- LINE C144 FOR OPEN z
Disconnect: In- Line C144.
z Check in-line C144 for damage; repair as necessary.
z Measure the resistance between in- line C144 Pin 13,
Circuit 915 (PK/LB), harness side and DLC C251 Pin
10, Circuit 915 (PK/LB), harness side.
z Is the resistance less than 5 ohms? Yes
REPAIR Circuit 915 (PK/LB)
between anti-
lock brake control
module C135 and in- line C144.
For additional information,
REFER to Communication Circuit Wiring Repair . TEST the
system for normal operation.
No
GO to A8 .
A8 CHECK CIRCUIT 915 (PK/LB) BETWEEN DLC C251
AND IN- LINE C215 FOR OPEN z
Disconnect: In- Line C215.
z Check in-line C215 for damage; repair as necessary.
z Measure the resistance between in- line C215 Pin 13,
Circuit 915 (PK/LB), harness side and DLC C251 Pin Yes
REPAIR Circuit 915 (PK/LB)
between in-
line C144 and in- line
C215. For additional Klj . 6 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

10, Circuit 915 (PK/LB), harness side.
z Is the resistance less than 5 ohms? information, REFER to
Communication Circuit Wiring
Repair . TEST the system for
normal operation.
No
REPAIR Circuit 915 (PK/LB)
between DLC C251 and in- line
C215. For additional
information, REFER to
Communication Circuit Wiring Repair . TEST the system for
normal operation. A9 CHECK FOR OPEN BETWEEN THE DLC C251 AND
ANTI- LOCK BRAKE CONTROL MODULE C135 — CIRCUIT
70 (LB/WH) z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C135.
z Inspect anti- lock brake control module C135 for
damage, repair as necessary.
z Measure the resistance between anti- lock brake control
module C135 Pin 24, Circuit 70 (LB/WH), harness side
and DLC C251 Pin 7, Circuit 70 (LB/WH), harness side.
z Is the resistance less than 5 ohms? Yes
INSTALL a new anti-
lock brake
control module. REFER to
Section 206 - 09A . TEST the
system for normal operation.
No
GO to A10 .
A10 CHECK FOR OPEN BETWEEN THE DLC C251 AND
IN- LINE C140 z
Disconnect: In- Line C140.
z Inspect in- line C140 for damage, repair as necessary.
z Measure the resistance between in- line C140 Pin 7,
Circuit 70 (LB/WH), harness side and DLC C251 Pin 7,
Circuit 70 (LB/WH), harness side.
z Is the resistance less than 5 ohms? Yes
REPAIR Circuit 70 (LB/WH)
between in-
line C140 and anti-
lock brake control module C135.
TEST the system for normal
operation.
No
GO to A11 .
A11 CHECK FOR OPEN BETWEEN THE DLC C251 AND
IN- LINE C314 z
Disconnect: In- Line C314.
z Inspect in- line C314 for damage, repair as necessary. Yes
REPAIR Circuit 70 (LB/WH) Klj . 7 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the voltage indicated in either measurement zero
volts? F4 CHECK FOR SHORT TO GROUND AND POWER AT
DLC C251 — RCM C2041 DISCONNECTED z
Key in OFF position.
z Deactivate the air bag system; REFER to Section 501 -
20B .
z Disconnect: RCM C2041.
z Key in ON position.
z Measure the voltage between DLC C251 Pin 7, Circuit 70
(LB/WH), harness side and C251 Pin 4, Circuit 1205
(BK); and between DLC C251 Pin 7, Circuit 70 (LB/WH),
harness side and C251 Pin 16, Circuit 1047 (LG/RD),
harness side.
z Is the voltage indicated in either measurement zero
volts? Yes
REPAIR Circuit 70 (LB/WH)
between DLC C251, GEM
C201e, RCM C2041, and in-
line C314. TEST the system
for normal operation.
No
INSTALL a new RCM. REFER
to
Section 501 - 20B . TEST the
system for normal operation. F5 CHECK FOR THE ANTI-
LOCK BRAKE CONTROL
MODULE z
Key in OFF position.
z Connect: In- Line C3141.
z Check the vehicle for any version of the anti- lock brake
control module.
z Is the vehicle equipped with any version of the anti-
lock brake control module (with or without traction
control)? Yes
GO to
F6 .
No
GO to F7 .
F6 CHECK FOR SHORT TO GROUND AND POWER AT
DLC C251 — ANTI-LOCK BRAKE CONTROL MODULE C135
DISCONNECTED z
Disconnect: Anti- Lock Brake Control Module C135.
z Key in ON position.
z Measure the voltage between DLC C251 Pin 7, Circuit 70
(LB/WH), harness side and C251 Pin 4, Circuit 1205
(BK); and between DLC C251 Pin 7, Circuit 70 (LB/WH),
harness side and C251 Pin 16, Circuit 1047 (LG/RD),
harness side. Yes
GO to
F7 .
No
INSTALL a new anti- lock brake
control module. For additional
information on the anti- lock
brake control module without
traction control, REFER to Klj . 13 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST G: NO MODULE/NETWORK COMMUNICATION —
SCP NETWORK z
Is the voltage indicated in either measurement zero
volts? Section 206 - 09A . For
additional information on the
anti- lock brake control module
with traction control, REFER to
Section 206 - 09B . TEST the
system for normal operation. F7 CHECK FOR SHORT TO GROUND AND POWER AT
DLC C251 — IN-LINE C140 DISCONNECTED z
Key in OFF position.
z Disconnect: In- Line C140.
z Key in ON position.
z Measure the voltage between DLC C251 Pin 7, Circuit 70
(LB/WH), harness side and C251 Pin 4, Circuit 1205
(BK); and between DLC C251 Pin 7, Circuit 70 (LB/WH),
harness side and C251 Pin 16, Circuit 1047 (LG/RD),
harness side.
z Is the voltage indicated in either measurement zero
volts? Yes
REPAIR Circuit 70 (LB/WH)
between in-
line C314 and in-
line C140. TEST the system
for normal operation.
No
REPAIR Circuit 70 (LB/WH)
between in- line C140 and the
anti-lock brake control module
C135. TEST the system for
normal operation. Test Step Result / Action to Take
G1 CHECK DIAGNOSTIC TOOL PINS FOR DAMAGE
z
Inspect diagnostic tool pins for damage.
z Are the diagnostic tool pins OK? Yes
GO to
G2 .
No
REPAIR the diagnostic tool
terminals. TEST the system for
normal operation. Klj . 14 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

G2 CHECK DLC C251 PINS 2 AND 10 FOR DAMAGE
z
Key in OFF position.
z Inspect the DLC C251 pins for damage.
z Are the pins OK? Yes
GO to
G3 .
No
REPAIR the DLC C251. TEST
the system for normal operation. G3 CHECK THE VEHICLE FOR THE ANTI-
LOCK BRAKE
CONTROL MODULE z
Check the vehicle for any version of the anti- lock brake
control module.
z Is the vehicle equipped with any version of the anti-
lock brake control module (with or without traction
control)? Yes
GO to
G4 .
No
GO to G7 .
G4 CHECK CIRCUIT 914 (TN/OG) AND CIRCUIT 915
(PK/LB) FOR OPEN — ANTI-LOCK BRAKE CONTROL
MODULE C135 DISCONNECTED z
Disconnect: Anti- Lock Brake Control Module C135.
z Measure the resistance between anti- lock brake control
module C135 Pin 30, Circuit 914 (TN/OG), harness
side and DLC C251 Pin 2, Circuit 914 (TN/OG),
harness side.
z Measure the resistance between anti- lock brake control
module C135 Pin 29, Circuit 915 (PK/LB), harness side
and DLC C251 Pin 10, Circuit 915 (PK/LB), harness
side.
z Are the resistances less than 5 ohms? Yes
GO to
G5 .
No
REPAIR the circuit(s) in question
between in- line C215 and DLC
C251. For additional information,
REFER to Communication Circuit Wiring Repair . TEST the
system for normal operation. G5 CHECK CIRCUIT 914 (TN/OG) AND CIRCUIT 915 Klj . 15 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

(PK/LB) FOR THE SOURCE OF THE CONCERN — ANTI-
LOCK BRAKE CONTROL MODULE C135 DISCONNECTED z
Key in ON position.
z Measure the voltage between DLC C251 Pin 2, Circuit
914 (TN/OG), harness side and C251 Pin 4, Circuit
1205 (BK); and between DLC C251 Pin 2, Circuit 914
(TN/OG), harness side and C251 Pin 16, Circuit 1047
(LG/RD), harness side.
z Measure the voltage between DLC C251 Pin 10,
Circuit 915 (PK/LB), harness side and C251 Pin 4,
Circuit 1205 (BK); and between DLC C251 Pin 10,
Circuit 915 (PK/LB), harness side and C251 Pin 16,
Circuit 1047 (LG/RD), harness side.
z Is the voltage zero volts for any measurement? Yes
GO to
G6 .
No
INSTALL a new anti- lock brake
control module. For additional
information on the anti- lock brake
control module without traction
control, REFER to Section 206 -
09A . For additional information
on the anti- lock brake control
module with traction control,
REFER to Section 206 - 09B .
TEST the system for normal
operation. G6 CHECK CIRCUIT 914 (TN/OG) AND CIRCUIT 915
(PK/LB) FOR THE SOURCE OF THE CONCERN — IN-LINE
C144 DISCONNECTED z
Key in OFF position.
z Disconnect: In- Line C144.
z Key in ON position.
z Measure the voltage between DLC C251 Pin 2, Circuit
914 (TN/OG), harness side and C251 Pin 4, Circuit
1205 (BK); and between DLC C251 Pin 2, Circuit 914
(TN/OG), harness side and C251 Pin 16, Circuit 1047
(LG/RD), harness side.
z Measure the voltage between DLC C251 Pin 10,
Circuit 915 (PK/LB), harness side and C251 Pin 4, Yes
GO to
G8 .
No
REPAIR the circuit(s) in question
between in- line C144 and the
anti- lock brake control module
C135. REFER to Communication Circuit Wiring Repair . TEST the
system for normal operation. Klj . 16 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Measure the voltage between DLC C251 Pin 10,
Circuit 915 (PK/LB), harness side and C251 Pin 4,
Circuit 1205 (BK); and between DLC C251 Pin 10,
Circuit 915 (PK/LB), harness side and C251 Pin 16,
Circuit 1047 (LG/RD), harness side.
z Is the voltage zero volts for any measurement? G9 CHECK CIRCUIT 914 (TN/OG) AND CIRCUIT 915
(PK/LB) FOR THE SOURCE OF THE CONCERN — IN-LINE
C215 DISCONNECTED z
Key in OFF position.
z Disconnect: In- Line C215.
z Key in ON position.
z Measure the voltage between DLC C251 Pin 2, Circuit
914 (TN/OG), harness side and C251 Pin 4, Circuit
1205 (BK); and between DLC C251 Pin 2, Circuit 914
(TN/OG), harness side and C251 Pin 16, Circuit 1047
(LG/RD), harness side.
z Measure the voltage between DLC C251 Pin 10,
Circuit 915 (PK/LB), harness side and C251 Pin 4,
Circuit 1205 (BK); and between DLC C251 Pin 10,
Circuit 915 (PK/LB), harness side and C251 Pin 16,
Circuit 1047 (LG/RD), harness side. Yes
GO to
G10 .
No
REPAIR the circuit(s) in question
between in- line C215, in - line
C144 (if equipped with the anti-
lock brake control module), and
the PCM C175. For additional
information, REFER to
Communication Circuit Wiring Repair . TEST the system for
normal operation. Klj . 18 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Short to Battery
B1317 Battery Voltage High GEM GO to
Section 414 - 00 .
B1318 Battery Voltage Low GEM GO to
Section 414 - 00 .
B1322 Door Ajar Driver Circuit Short
to Ground GEM GO to
Section 417 - 02 .
B1330 Door Ajar Passenger Circuit
Short to Ground GEM GO to
Section 417 - 02 .
B1334 Decklid Ajar Rear Door
Circuit Short to Ground GEM GO to
Section 417 - 02 .
B1339 Chime Input Request Circuit
Short to Battery GEM GO to
Section 413 - 09 .
B1340 Chime Input Request Circuit
Short to Ground GEM GO to
Section 413 - 09 .
B1342 ECU is Defective GEM CLEAR the DTC. RETRIEVE the DTCs. If DTC
B1342 is retrieved, INSTALL a new GEM. REFER to
Section 419
- 10 .
B1353 Ignition Key-
in Circuit Open GEM GO to
Section 413 - 09 .
B1359 Ignition RUN/ACC Circuit
Failure GEM GO to
Section 211 - 05 .
B1396 Power Door Lock Circuit
Short to Battery GEM GO to
Section 501 - 14B .
B1397 Power Door Unlock Circuit
Short to Battery GEM GO to
Section 501 - 14B .
B1405 Power Window Driver Down
Circuit Short to Battery GEM GO to
Pinpoint Test D for convertible or
Pinpoint Test E for coupe.
B1408 Power Window Driver Up
Circuit Short to Battery GEM GO to
Pinpoint Test D for convertible or
Pinpoint Test E for coupe.
B1410 Power Window Driver Motor
Circuit Failure GEM GO to
Pinpoint Test D for convertible or
Pinpoint Test E for coupe.
B1426 Lamp Safety Belt Circuit
Short to Battery GEM REFER to
Section 413 - 01 .
B1428 Lamp Safety Belt Circuit
Failure GEM REFER to
Section 413 - 01 .
B1431 Wiper Brake/run Relay Circuit
Failure GEM GO to
Section 501 - 16 .
B1432 Wiper Brake/run Relay Circuit
Short to Battery GEM GO to
Section 501 - 16 .
B1434 Wiper High/low Speed Relay
Coil Circuit Failure GEM GO to
Section 501 - 16 .
B1436 Wiper High/low Speed Relay
Coil Circuit Short to Battery GEM GO to
Section 501 - 16 .
B1438 Wiper Mode Select Switch
Circuit Failure GEM GO to
Section 501 - 16 .
B1441 Wiper Mode Select Switch
Circuit Short to Ground GEM GO to
Section 501 - 16 .
B1446 Wiper Park Sense Circuit
Failure GEM GO to
Section 501 - 16 .
B1448 Wiper Park Sense Circuit
Short to Battery GEM GO to
Section 501 - 16 . Klj . 3 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

B1450 Wiper Wash/delay Switch
Circuit Failure GEM GO to
Section 501 - 16 .
B1453 Wiper Wash/delay Switch
Circuit Short to Ground GEM GO to
Section 501 - 16 .
B1458 Wiper Washer Pump Motor
Relay Circuit Failure GEM GO to
Section 501 - 16 .
B1460 Wiper Washer Pump Motor
Relay Circuit Short to Battery GEM GO to
Section 501 - 16 .
B1462 Safety Belt Switch Circuit
Failure GEM GO to
Section 413 - 09 .
B1466 Wiper High/low Speed Not
Switching GEM GO to
Section 501 - 16 .
B1473 Wiper Low Speed Circuit
Motor Failure GEM GO to
Section 501 - 16 .
B1476 Wiper High Speed Circuit
Motor Failure GEM GO to
Section 501 - 16 .
B1498 Decklid Punch-
out Sensor
Ground Short GEM GO to
Section 419 - 01 .
B1551 Decklid Release Circuit
Failure GEM GO to
Section 501 - 14B .
B1553 Decklid Release Circuit Short
to Battery GEM GO to
Section 501 - 14B .
B1555 Ignition RUN/START Circuit
Failure GEM GO to
Section 211 - 05 .
B1603 Lamp Anti-
Theft Indicator
Circuit Failure GEM GO to
Section 419 - 01 .
B1605 Lamp Anti-
Theft Indicator
Circuit Short to Battery GEM GO to
Section 419 - 01 .
B1687 Lamp Dome Input Circuit
Short to Battery GEM GO to
Section 417 - 02 .
B1833 Door Unlock Disarm Switch
Circuit Short to Ground GEM GO to
Section 419 - 01 .
B2486 Parklamp Output Relay Driver
Circuit Failure GEM GO to
Section 419 - 01 .
B2488 Parklamp Output Relay Driver
Circuit Short to Battery GEM GO to
Section 419 - 01 .
C1189 Brake Fluid Level Sensor
Input Circuit Short to Ground GEM REFER to
Section 413 - 01 .
C1223 Lamp Brake Warning Output
Circuit Failure GEM REFER to
Section 413 - 01 .
C1225 Lamp Brake Warning Output
Circuit Short to Battery GEM REFER to
Section 413 - 01 .
ICM DIAGNOSTIC TROUBLE CODE (DTC) INDEX DTC Description Source Action
B1343 Heated Backlight Input Circuit Failure ICM GO to
Pinpoint Test H . Klj . 4 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...