Seat control FORD MUSTANG 2003 Owner's Guide

PINPOINT TEST D: INCORRECT TEMPERATURE GAUGE
INDICATION
PINPOINT TEST E: INCORRECT VOLTAGE GAUGE INDICATION—
EXCEPT COBRA z
Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster connectors and make sure they
seat correctly.
z Operate the system and verify the concern is still present.
z Is the concern still present? instrument cluster.
REFER to
Instrument Cluster in this section.
TEST the system for
normal operation.
No
The system is
operating correctly at
this time. Concern may
have been caused by a
loose or corroded
connector. CLEAR the
DTCs. REPEAT the
self- test. Test Step Result / Action to Take
D1 CARRY OUT THE INSTRUMENT CLUSTER
ENGINE COOLANT TEMPERATURE GAUGE
ACTIVE COMMAND z
Connect the diagnostic tool.
z Key in ON position.
z Enter the following diagnostic mode on the
diagnostic tool: Instrument Cluster Active
Command.
z Trigger instrument cluster active command
ENGCOOLNT. Monitor the engine coolant
temperature gauge while adjusting the
ENGCOOLNT active command to read 50%
and 100%.
z Does the temperature gauge start at cold,
move to half at 50%, and full hot at 100%? Yes
REFER to the Powertrain
Control/Emissions Diagnosis (PC/ED)
manual.
No
GO to
D2 .
D2 CHECK FOR CORRECT INSTRUMENT
CLUSTER OPERATION z
Disconnect all instrument cluster connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster connectors and
make sure they seat correctly.
z Operate the system and verify the concern is
still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster.
REFER to
Instrument Cluster in this
section. TEST the system for normal
operation.
No
The system is operating correctly at this
time. Concern may have been caused by
a loose or corroded connector. CLEAR the
DTCs. REPEAT the self-test. Test Step Result / Action to
Take E1 CHECK THE INSTRUMENT CLUSTER Klj . 19 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST F: INCORRECT TACHOMETER INDICATION
PINPOINT TEST G: INCORRECT BOOST GAUGE INDICATION—
COBRA ONLY REPEAT the self-
test. Test Step Result / Action to Take
F1 CHECK THE TACHOMETER
OPERATION z
Connect the diagnostic tool.
z Key in ON position.
z Enter the following diagnostic mode on
the diagnostic tool: Instrument Cluster
Active Command.
z Trigger the instrument cluster active
command TCHOMETER. Scroll to 0%,
50%, and 100%.
z Did the tachometer display read 0 at
0%, half the tachometer display at
50%, and the full tachometer display
at 100%? Yes
REFER to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual.
No
GO to
F2 .
F2 CHECK FOR CORRECT INSTRUMENT
CLUSTER OPERATION z
Disconnect all instrument cluster
connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster
connectors and make sure they seat
correctly.
z Operate the system and verify the
concern is still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster. REFER to
Instrument Cluster
in this section. TEST the
system for normal operation.
No
The system is operating correctly at this time.
Concern may have been caused by a loose or
corroded connector. CLEAR the DTCs.
REPEAT the self- test. Test Step Result / Action to Take
G1 CHECK BOOST GAUGE
PRESSURE LINE z
Disconnect the boost gauge
pressure line from the intake
manifold.
z Apply 69 kPa (10 psi) to the boost
gauge pressure line.
z Does the boost gauge indicate
maximum boost pressure? Yes
CHECK for a plugged manifold fitting. TEST the
system for normal operation.
No
GO to
G2 .
G2 CHECK THE BOOST GAUGE
z
Disconnect the boost gauge
pressure line from the instrument
cluster.
z Apply 10 psi to the boost gauge.
z Does the boost gauge indicate
maximum boost pressure? Yes
INSTALL a new boost gauge pressure line. TEST the
system for normal operation.
No
INSTALL a new instrument cluster. REFER to Klj . 21 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST H: THE LOW FUEL WARNING INDICATOR IS
NEVER/ALWAYS ON
PINPOINT TEST I: THE SPEEDOMETER IS INOPERATIVE Instrument Cluster in this section. TEST the system
for normal operation. Test Step Result / Action to Take
H1 CARRY OUT THE INSTRUMENT CLUSTER
WARNING LAMPS AND CHIME ACTIVE
COMMAND USING THE DIAGNOSTIC TOOL z
Key in OFF position.
z Connect the diagnostic tool.
z Key in ON position.
z Enter the following diagnostic mode on the
diagnostic tool: Instrument Cluster Active
Command.
z Select the instrument cluster WARNING
LAMPS AND CHIME active command. Trigger
the ALL LAMPS active command. Observe the
LOW FUEL warning indicator.
z Is the LOW FUEL warning indicator
illuminating? Yes
GO to
H2 .
No
GO to H3 .
H2 THE LOW FUEL GAUGE WARNING
INDICATOR IS NEVER/ALWAYS ON z
Check the fuel gauge for correct operation.
z Is the fuel gauge operating correctly? Yes
GO to
H3 .
No
Go To Pinpoint Test B .
H3 CHECK FOR CORRECT INSTRUMENT
CLUSTER OPERATION z
Disconnect all instrument cluster connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster connectors and
make sure they seat correctly.
z Operate the system and verify the concern is
still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster.
REFER to
Instrument Cluster in this
section. TEST the system for normal
operation.
No
The system is operating correctly at this
time. Concern may have been caused by
a loose or corroded connector. CLEAR
the DTCs. REPEAT the self-test. Test Step Result / Action to Take
I1 TEST THE INSTRUMENT
CLUSTER z
Carry out the instrument cluster
self- diagnostic mode.
z Did the gauge sweep? Yes
REFER to the Powertrain Control/Emissions Diagnosis
(PC/ED) manual.
No Klj . 22 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST J: THE ODOMETER IS INOPERATIVE
PINPOINT TEST K: THE SAFETY BELT INDICATOR IS INOPERATIVE
(CHIME IS OPERATIVE)/DOES NOT OPERATE CORRECTLY GO to
I2 .
I2 CHECK FOR CORRECT
INSTRUMENT CLUSTER
OPERATION z
Disconnect all instrument cluster
connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster
connectors and make sure they
seat correctly.
z Operate the system and verify
the concern is still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster. REFER to
Instrument Cluster
in this section. TEST the system for
normal operation.
No
The system is operating correctly at this time. Concern
may have been caused by a loose or corroded
connector. CLEAR the DTCs. REPEAT the self- test. Test Step Result / Action to Take
J1 CHECK THE ODOMETER
DISPLAY z
Key in ON position.
z Is the odometer displaying all
dashes? Yes
REFER to the Powertrain Control/Emissions Diagnosis
(PC/ED) manual.
No
GO to
J2 .
J2 CHECK FOR CORRECT
INSTRUMENT CLUSTER
OPERATION z
Disconnect all instrument cluster
connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster
connectors and make sure they
seat correctly.
z Operate the system and verify
the concern is still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster. REFER to
Instrument Cluster
in this section. TEST the system for
normal operation.
No
The system is operating correctly at this time. Concern
may have been caused by a loose or corroded
connector. CLEAR the DTCs. REPEAT the self- test. Test Step Result / Action to Take
K1 CHECK IF THE GEM IS RECEIVING THE CORRECT
IGNITION SWITCH STATUS CAUTION: Use the correct probe adapter(s) when
making measurements. Failure to use the correct probe
adapter(s) may damage the connector.
z Connect the diagnostic tool. Yes
GO to
K2 .
No
REFER to Section 211 - 05 . Klj . 23 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST L: INACCURATE SPEEDOMETER READING
PINPOINT TEST M: THE O/D OFF INDICATOR IS NEVER ON Concern may have been
caused by a loose or
corroded connector. CLEAR
the DTCs. REPEAT the self-
test.
K11 CHECK FOR CORRECT INSTRUMENT CLUSTER
OPERATION z
Disconnect all instrument cluster connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster connectors and make sure
they seat correctly.
z Operate the system and verify the concern is still present.
z Is the concern still present? Yes
INSTALL a new instrument
cluster. REFER to
Instrument Cluster
in this
section. TEST the system
for normal operation.
No
The system is operating
correctly at this time.
Concern may have been
caused by a loose or
corroded connector. CLEAR
the DTCs. REPEAT the self-
test. Test Step Result / Action to Take
L1 CHECK SPEEDOMETER OPERATION
z
Connect the diagnostic tool.
z Key in ON position.
z Enter the following diagnostic mode on
the diagnostic tool: Instument Cluster
Active Command.
z Trigger the instrument cluster active
command SPDOMETER. Scroll to 0%,
50%, and 100%.
z Did the speedometer display read 0 at
0%, half the speedometer display at
50%, and the full speedometer display
at 100%? Yes
REFER to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual.
No
GO to
L2 .
L2 CHECK FOR CORRECT INSTRUMENT
CLUSTER OPERATION z
Disconnect all instrument cluster
connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster
connectors and make sure they seat
correctly.
z Operate the system and verify the
concern is still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster. REFER to
Instrument Cluster
in this section. TEST the
system for normal operation.
No
The system is operating correctly at this time.
Concern may have been caused by a loose or
corroded connector. CLEAR the DTCs.
REPEAT the self- test. Klj . 26 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST N: THE CHECK FUEL CAP INDICATOR IS NEVER
ON Test Step Result / Action to Take
M1 CHECK THE O/D OFF
INDICATOR OPERATION z
Key in ON position.
z Observe the O/D OFF indicator.
z Is the O/D OFF indicator
always on? Yes
GO to
M2 .
No
GO to M3 .
M2 CHECK THE INSTRUMENT
CLUSTER z
Key in OFF position.
z Disconnect: Instrument Cluster
C220a.
z Key in ON position.
z Observe the O/D OFF indicator.
z Did the indicator turn off? Yes
REFER to the Powertrain Control/Emissions Diagnosis
(PC/ED) manual.
No
GO to
M4 .
M3 CHECK THE INSTRUMENT
CLUSTER OPERATION z
Carry out the instrument cluster
self- diagnostic mode.
z Did the O/D OFF indicator
illuminate? Yes
REFER to the Powertrain Control/Emissions Diagnosis
(PC/ED) manual.
No
GO to
M4 .
M4 CHECK FOR CORRECT
INSTRUMENT CLUSTER
OPERATION z
Disconnect all instrument cluster
connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster
connectors and make sure they
seat correctly.
z Operate the system and verify
the concern is still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster. REFER to
Instrument Cluster
in this section. TEST the system for
normal operation.
No
The system is operating correctly at this time. Concern
may have been caused by a loose or corroded
connector. CLEAR the DTCs. REPEAT the self- test. Test Step Result / Action to Take
N1 RETREIVE AND RECORD DTCS FROM
CONTINUOUS AND ON- DEMAND SELF-TESTS—
PCM NOTE:
Once the check fuel cap indicator
does turn on, it does not turn off unless the
fuel cap has been correctly secured and the
vehicle has been driven for several minutes.
z Use recorded PCM DTCs from the
continuous and on- demand self-test.
z Are any DTCs recorded? Yes
If PCM DTC P0457, REFER to the
Powertrain Control/Emissions Diagnosis
(PC/ED) manual.
No
GO to
N2 .
N2 CARRY OUT THE INSTRUMENT CLUSTER Klj . 27 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST O: THE BRAKE WARNING INDICATOR IS
NEVER/ALWAYS ON INDICATOR LAMP CONTROL III ACTIVE
COMMAND USING THE DIAGNOSTIC TOOL
z
Connect the diagnostic tool.
z Enter the following diagnostic mode on the
diagnostic tool: Instrument Cluster Active
Command.
z Select the instrument cluster INDICATOR
LAMP CONTROL III active command.
Trigger the CHECK FUEL CAP active
command ON. Observe the CHECK FUEL
CAP indicator.
z Does the CHECK FUEL CAP indicator
illuminate? Yes
REFER to the Powertrain
Control/Emissions Diagnosis (PC/ED)
manual.
No
GO to
N3 .
N3 CHECK FOR CORRECT INSTRUMENT
CLUSTER OPERATION z
Disconnect all instrument cluster connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster connectors
and make sure they seat correctly.
z Operate the system and verify the concern is
still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster. REFER
to
Instrument Cluster in this section. TEST
the system for normal operation.
No
The system is operating correctly at this
time. Concern may have been caused by a
loose or corroded connector. CLEAR the
DTCs. REPEAT the self- test. Test Step Result / Action to Take
O1 CHECK IF THE GEM IS RECEIVING THE CORRECT
IGNITION SWITCH STATUS CAUTION: Use the correct probe adapter(s) when
making measurements. Failure to use the correct probe
adapter(s) may damage the connector.
z Connect the diagnostic tool.
z Key in ON position.
z Enter the following diagnostic mode on the diagnostic tool:
Generic Electronic Module (GEM) PID.
z Monitor GEM PIDs IGN_KEY, IGN_S, IGN_R, and IGN_A
while cycling the ignition switch through all positions and
then removing the key from ignition switch.
z Do the PIDs agree with the ignition switch status? Yes
GO to
O2 .
No
REFER to Section 211 - 05 .
O2 DETERMINE IF GEM IS RECEIVING THE CORRECT
PARKING BRAKE INPUT z
Monitor GEM PID PRK_BRK while applying and releasing
the parking brake.
z Did the PID read ON with the parking brake applied, and
OFF with the parking brake released? Yes
GO to
O3 .
No
GO to O5 .
O3 DETERMINE IF BRAKE WARNING INDICATOR CIRCUIT IS
OPEN OR GROUNDED z
Verify that the parking brake is released.
z Is the instrument cluster BRAKE warning indicator off? Yes
GO to
O4 . Klj . 28 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST R: THE ABS WARNING INDICATOR IS NEVER ON z
Key in OFF position.
z Disconnect: Instrument Cluster C220b.
z Key in ON position.
z Measure the voltage between the instrument cluster C220b
pin 2, circuit 12 (LG/BK), harness side and ground, while
turning the high beams on and off.
z Is the voltage 0 volts with the high beams off and
greater than 10 volts with the high beams on? Yes
GO to
Q3 .
No
REPAIR the circuit. TEST
the system for normal
operation. Q3 CHECK FOR CORRECT INSTRUMENT CLUSTER
OPERATION z
Disconnect all instrument cluster connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster connectors and make sure
they seat correctly.
z Operate the system and verify the concern is still present.
z Is the concern still present? Yes
INSTALL a new instrument
cluster. REFER to
Instrument Cluster
in this
section. TEST the system
for normal operation.
No
The system is operating
correctly at this time.
Concern may have been
caused by a loose or
corroded connector. CLEAR
the DTCs. REPEAT the self-
test. Test Step Result / Action to Take
R1 CHECK THE ABS WARNING INDICATOR OPERATION
CAUTION: Use the correct probe adapter(s) when
making measurements. Failure to use the correct probe
adapter(s) may damage the connector.
z Key in ON position.
z Observe the ABS warning indicator. The ABS indicator
should prove out for approximately six seconds then turn off.
z Does the ABS warning indicator operate correctly? Yes
The system is operating
normally at this time.
No
If the indicator is
inoperative, GO to
R2 .
If the indicator is always
on, REFER to Section 206 -
09A or
Section 206 - 09B .
R2 CHECK THE INSTRUMENT CLUSTER INPUT
z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C135.
z Connect a fused (10A) jumper wire between the anti- lock
brake control module C135 pin 16, circuit 603 (DG), harness Yes
REFER to
Section 206 - 09A
or
Section 206 - 09B . Klj . 34 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST S: THE SERVICE ENGINE SOON INDICATOR IS
NEVER/ALWAYS ON side and ground.
z Key in ON position.
z Does the ABS indicator illuminate? No
GO to
R3 .
R3 CHECK CIRCUIT 603 (DG) FOR AN OPEN
z
Key in OFF position.
z Disconnect: Instrument Cluster C220b.
z Measure the resistance between the instrument cluster
C220b pin 15, circuit 603 (DG), harness side and the anti-
lock brake control module C135 pin 16, circuit 603 (DG),
harness side.
z Is the resistance less than 5 ohms? Yes
GO to
R4 .
No
REPAIR the circuit. TEST
the system for normal
operation. R4 CHECK FOR CORRECT INSTRUMENT CLUSTER
OPERATION z
Disconnect all instrument cluster connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster connectors and make sure
they seat correctly.
z Operate the system and verify the concern is still present.
z Is the concern still present? Yes
INSTALL a new instrument
cluster. REFER to
Instrument Cluster
in this
section. TEST the system
for normal operation.
No
The system is operating
correctly at this time.
Concern may have been
caused by a loose or
corroded connector.
CLEAR the DTCs.
REPEAT the self- test. Test Step Result / Action to Take
S1 CARRY OUT THE INSTRUMENT Klj . 35 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST T: THE TURN/HAZARD INDICATOR IS
NEVER/ALWAYS ON CLUSTER SERVICE ENGINE SOON
INDICATOR ACTIVE COMMAND
z
Connect the diagnostic tool.
z Key in ON position.
z Enter the following diagnostic mode
on the diagnostic tool: Instrument
Cluster Active Command.
z Trigger the instrument cluster active
command MIL.
z Did the SERVICE ENGINE SOON
indicator illuminate? Yes
REFER to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual.
No
GO to
S2 .
S2 CHECK FOR CORRECT
INSTRUMENT CLUSTER OPERATION z
Disconnect all instrument cluster
connectors.
z Check for:
zcorrosion
z pushed- out pins
z Connect all instrument cluster
connectors and make sure they seat
correctly.
z Operate the system and verify the
concern is still present.
z Is the concern still present? Yes
INSTALL a new instrument cluster. REFER to
Instrument Cluster
in this section. TEST the
system for normal operation.
No
The system is operating correctly at this time.
Concern may have been caused by a loose or
corroded connector. CLEAR the DTCs. REPEAT
the self- test. Test Step Result / Action to
Take T1 CHECK THE TURN SIGNAL AND HAZARD LAMPS OPERATION
CAUTION: Use the correct probe adapter(s) when making
measurements. Failure to use the correct probe adapter(s) may
damage the connector.
z Key in ON position.
z Operate the left and right turn signals.
z Operate the hazard lamps.
z Do the turn signals and hazard lamps operate correctly? Yes
GO to
T2 .
No
REFER to Section 417 - 01 .
T2 CHECK THE CIRCUIT IN QUESTION —
CIRCUIT 2 (WH/LB) (RH)
OR CIRCUIT 3 (LG/WH) (LH) z
Key in OFF position.
z Disconnect: Instrument Cluster C220a (RH) or C220b (LH).
z Key in ON position.
z Measure the voltage between the instrument cluster C220a pin 3,
circuit 3 (LG/WH), harness side and ground, while the steering
column multifunction switch is placed in the left turn position (LH); or
between the instrument cluster C220b pin 3, circuit 2 (WH/LB),
harness side and ground, while the steering column multifunction
switch is placed in the right turn position (RH). Yes
GO to
T3 .
No
REPAIR the circuit
(s) in question.
TEST the system for
normal operation. Klj . 36 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...