cooling FORD MUSTANG 2003 Owner's Guide

IN-
VEHICLE REPAIR
Intake Manifold
Removal 1. Drain the engine cooling system. For additional information, refer to Section 303 - 03A or
Section 303 - 03B .
2. Remove the air cleaner outlet tube. For additional information, refer to Section 303 - 12 .
3. Disconnect the fuel line. For additional information, refer to Section 310 - 00 .
4. Disconnect the upper radiator hose from the water outlet connector.
5. Disconnect and remove the upper radiator hose.
6. Disconnect the accelerator cable, speed control actuator cable and return spring.
SECTION 303-
01B: Engine — 4.6L (2V) 2003 Mustang Workshop Manual Klj . 1 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

40. Refill the engine cooling system. For additional information, refer to
Section 303 - 03A or
Section 303 - 03B . Klj . 20 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Engine Front Cover
Removal 1. Remove the nuts and position the radio ignition interference capacitors aside.
2. Remove the valve covers. For additional information, refer to Valve Cover RH and
Valve Cover LH in this section.
3. Remove the cooling fan. For additional information, refer to Section 303 - 03A or
Section 303 -
03B .
4. Remove the accessory drive belt. For additional information, refer to Section 303 - 05 .
5. Remove bolts (1) and the water pump pulley (2).
6. Remove the nut and position the A/C muffler aside.
SECTION 303-
01B: Engine — 4.6L (2V) 2003 Mustang Workshop Manual Material
Item Specification
Silicone Gasket and Sealant
F7AZ-
19554- EA or equivalent WSE-
M4G323-
A4 Super Premium SAE 5W-20
Motor Oil
XO- 5W20- QSP or equivalent WSS-
M2C153- H Klj . 1 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13. Position the battery cable and install the two nuts.
14. Install the crankshaft pulley. For additional information, refer to
Crankshaft Pulley in this section.
15. Install the water pump pulley and the bolts.
16. Install the cooling fan. For additional information, refer to Section 303 - 03A or
Section 303 - 03B .
17. Install the accessory drive belt. For additional information, refer to Section 303 - 05 .
18. Install the valve covers. For additional information, refer to Valve Cover RH and
Valve Cover LH in this section.
19. Position the radio ignition interference capacitors and install the nuts. Klj . 8 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Oil Filter Adapter
Removal and Installation 1. Drain the cooling system. For additional information, refer to Section 303 - 03A or
Section 303 -
03B .
2. Disconnect the lower radiator hose.
3. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
4. Drain the engine oil.
5. Disconnect the oil pressure sensor electrical connector.
SECTION 303-
01B: Engine — 4.6L (2V) 2003 Mustang Workshop Manual Material
Item Specification
Super Premium SAE 5W-20
Motor Oil
XO- 5W20 QSP or equivalent WSS-
M2C153-
H Premium Engine Coolant
VC-
4A (In Canada CXC- 10; In
Oregon VC- 5) or equivalent ESE-
M97B44-
A Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL
Engine
Removal
1. Remove the hood.
2. Remove the battery. For additional information, refer to Section 414 - 01 .
3. Remove the air cleaner and outlet tube. For additional information, refer to Section 303 - 12 .
4. Drain the engine cooling system. For additional information, refer to Section 303 - 03A or
Section 303 - 03B .
5. Remove the degas bottle. For additional information, refer to Section 303 - 03A or
Section 303 -
03B .
6. Recover the A/C system. For additional information, refer to Section 412 - 00 .
7. Disconnect the fuel lines. For additional information, refer to Section 310 - 00 .
8. Disconnect the upper radiator hose from the water outlet connector.
SECTION 303-
01B: Engine — 4.6L (2V) 2003 Mustang Workshop Manual Special Tool(s)
Support Bracket, Engine
303-
639 Spreader Bar
303-
D089 (D93P-6001- A3) Lifting Bracket Set, Engine
303-
D074 (D91P-6001- A) Klj . 1 ba
122003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

b
P=Primary, S=Secondary, E=Exhaust
c Time necessary for plunger to leak down 1.6 mm of travel with 222 N force and leak down fluid in
tappet.
Torque Specifications Description Nm lb-
ft lb-
in A/C compressor bolts 25 18 —
A/C peanut fittings 8 — 71
A/C muffler nut 25 18 —
Accelerator bracket bolts 10 — 89
Battery tray bolts 11 8 —
Belt idler support bracket assembly fasteners 25 18 —
Camshaft sprocket bolt 115 85 —
Coolant bypass tube studs 25 18 —
Coolant bypass tube bolts 25 18 —
Coolant hose and tube assembly bolt 25 18 —
Cooling fan motor and shroud bolts 10 — 89
Connecting rod bolt
a — — —
Engine front cover bolt a a a
Drive belt tensioner bolts 25 18 —
Cylinder head bolt
a — — —
Idler pulley bracket 25 18 —
Power steering pump bolts 25 18 —
Power steering hose fitting 65 48 —
Power steering hose bracket bolt 10 — 89
Pulley to crankshaft bolt
a — — —
EGR valve to intake manifold
a — — —
Engine coolant degas bottle bolts 10 — 89
Exhaust manifold studs 25 18 —
Generator bolts 25 18 —
Generator support bracket bolts 25 18 —
Hood prop bolt 10 — 89
Hood mounting nuts 12 9 —
Heater water inlet tube 10 — 89
Heater water outlet tube 24 18 —
Lower intake manifold-
to-cylinder head bolt a — — —
Main bearing cap bolt
a — — —
Oil filter adapter bolt 25 18 —
Oil bypass filter to adapter 50 37 —
Oil pump screen cover and tube-
to-oil pump bolt 10 — 89
Oil pan-to-
cylinder block bolt a — — — Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
The inner rotor is piloted on the crankshaft post and is driven through flats on the crankshaft.
z System pressure is limited by an integral, internally- vented relief valve which directs the
bypassed oil back to the inlet side of the oil pump.
z Oil pump displacement has been selected to provide adequate volume to ensure correct oil
pressure both at hot idle and maximum speed.
z The relief valve calibration protects the system from excessive pressure during high viscosity
conditions.
z The relief valve is designed to provide adequate connecting rod bearing lubrication under high-
temperature and high- speed conditions.
Cooling System
The engine cooling system includes the following:
zradiator
z water pump
z the electric cooling fan motor and fan blade, activated by the variable control module
z the degas bottle, which aids in maintaining the correct volume of engine coolant
z water thermostat
z upper radiator hose
z lower radiator hose
z heater water hoses
Drive Belt System
The 4.6L (4V) DOHC engine is equipped with a serpentine drive belt. To ensure maximum life, a
replacement drive belt should be of the same type as originally installed.
zThe accessories mounted on the front of the engine are belt- driven by the crankshaft.
z The serpentine drive belt is routed over each accessory pulley, driven by the crankshaft pulley
bolted to the crankshaft.
For service procedures, including tensioning, refer to Section 303 - 05 . Klj . 3 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

28. Fill and bleed the engine cooling system. For additional information, refer to
Section 303 - 03A in
this section.
29. Fill and bleed the supercharger cooling system. For additional information, refer to Section 303 -
03B . Klj . 7 ba
72003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Crankshaft Pulley — Auxiliary
Removal and Installation 1. Remove the cooling fan. For additional information, refer to Section 303 - 03A .
2. Remove the supercharger drive belt cover.
3. Rotate the supercharger belt tensioner clockwise and remove the supercharger belt. 4. Remove the coolant hose assembly bolt. SECTION 303-
01C: Engine — Cobra 4.6L (4V) 2003 Mustang Workshop Manual Special Tool(s)
Locking Tool, Flywheel
303-
673 Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...