relay FORD MUSTANG 2003 Service Manual

B1408 Driver Power Window Up
Circuit Short to Battery GEM REFER to
Section 501 - 11 .
B1410 Driver Power Window Motor
Circuit Failure GEM REFER to
Section 501 - 11 .
B1426 Lamp Safety Belt Circuit
Short to Battery GEM REFER to
Section 413 - 01 .
B1428 Lamp Safety Belt Circuit
Failure GEM REFER to
Section 413 - 01 .
B1431 Wiper Brake/Run Relay
Circuit Failure GEM REFER to
Section 501 - 16 .
B1432 Wiper Brake/Run Relay
Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1434 Wiper Hi/Low Speed Relay
Coil Circuit Failure GEM REFER to
Section 501 - 16 .
B1436 Wiper Hi/Low Speed Relay
Coil Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1438 Wiper Mode Select Switch
Circuit Failure GEM REFER to
Section 501 - 16 .
B1441 Wiper Mode Select Switch
Circuit Short to Ground GEM REFER to
Section 501 - 16 .
B1446 Wiper Park Sense Circuit
Failure GEM REFER to
Section 501 - 16 .
B1448 Wiper Park Sense Circuit
Short to Battery GEM REFER to
Section 501 - 16 .
B1450 Wiper Wash/Delay Switch
Circuit Failure GEM REFER to
Section 501 - 16 .
B1453 Wiper Wash/Delay Switch
Circuit Short to Ground GEM REFER to
Section 501 - 16 .
B1458 Wiper Washer Pump Motor
Relay Circuit Failure GEM REFER to
Section 501 - 16 .
B1460 Wiper Washer Pump Motor
Relay Coil Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1462 Safety Belt Switch Circuit
Failure GEM REFER to
Section 413 - 09 .
B1466 Wiper Hi/Low Speed Not
Switching GEM REFER to
Section 501 - 16 .
B1473 Wiper Low Speed Circuit
Motor Failure GEM REFER to
Section 501 - 16 .
B1476 Wiper High Speed Circuit
Motor Failure GEM REFER to
Section 501 - 16 .
B1551 Decklid Release Circuit
Failure GEM REFER to
Section 501 - 14B .
B1553 Decklid Release Circuit
Short to Battery GEM REFER to
Section 501 - 14B .
B1555 Ignition Run/Start Circuit
Failure GEM REFER to
Section 211 - 05 .
B1687 Lamp Dome Input Circuit
Short to Battery GEM REFER to
Section 417 - 02 .
B2486 LF Side Repeater Lamp GEM REFER to
Section 417 - 01 . Klj . 4 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Inspection and Verification
1. Verify the customer concern by operating the system.
2. Visually inspect for obvious signs of mechanical or electrical damage.
3. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
4. If the diagnostic tool does not communicate with the vehicle, refer to the diagnostic tool manual.
5. Carry out the DATA LINK DIAGNOSTIC TEST. If the diagnostic tool responds with: zCKT 914, CKT 915 or CKT70 - ALL ECUS NO RESP/NOT EQUIP, refer to Section 418 -
00 .
z NO RESP/NOT EQUIP for the generic electronic module (GEM), go to Pinpoint Test A.
z NO RESP/NOT EQUIP for the instrument cluster module (ICM), refer to Section 413 - 01 .
z System passed, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs and carry out self- test diagnostics for the GEM or ICM.
6. If the GEM or ICM DTCs retrieved are related to the concern, go to the GEM or ICM Diagnostic Trouble Code (DTC) Index.
7. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.
GEM DIAGNOSTIC TROUBLE CODE (DTC) INDEX Visual Inspection Chart Mechanical Electrical
z
Power window
regulator
z Window run
weatherstrip
z Door window glass z
Central junction box (CJB) circuit breaker 43 (20A), fuse 39
(5A) or 23 (15A)
z Battery junction box (BJB) fuse HTD BL (40A)
z Generic electronic module (GEM)
z Window regulator control switch
z Window regulator motor
z Instrument cluster module (ICM)
z Heated rear window relay
z Rear window defrost switch
z Heated rear window grid
z Circuitry DTC Description Source Action
B1217 Horn Relay Output Driver
Circuit Failure GEM GO to
Section 501 - 14B .
B1218 Horn Relay Output Driver
Short to Battery GEM GO to
Section 501 - 14B .
B1312 Lamp Headlamp Input Circuit GEM GO to
Section 413 - 09 . Klj . 2 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Short to Battery
B1317 Battery Voltage High GEM GO to
Section 414 - 00 .
B1318 Battery Voltage Low GEM GO to
Section 414 - 00 .
B1322 Door Ajar Driver Circuit Short
to Ground GEM GO to
Section 417 - 02 .
B1330 Door Ajar Passenger Circuit
Short to Ground GEM GO to
Section 417 - 02 .
B1334 Decklid Ajar Rear Door
Circuit Short to Ground GEM GO to
Section 417 - 02 .
B1339 Chime Input Request Circuit
Short to Battery GEM GO to
Section 413 - 09 .
B1340 Chime Input Request Circuit
Short to Ground GEM GO to
Section 413 - 09 .
B1342 ECU is Defective GEM CLEAR the DTC. RETRIEVE the DTCs. If DTC
B1342 is retrieved, INSTALL a new GEM. REFER to
Section 419
- 10 .
B1353 Ignition Key-
in Circuit Open GEM GO to
Section 413 - 09 .
B1359 Ignition RUN/ACC Circuit
Failure GEM GO to
Section 211 - 05 .
B1396 Power Door Lock Circuit
Short to Battery GEM GO to
Section 501 - 14B .
B1397 Power Door Unlock Circuit
Short to Battery GEM GO to
Section 501 - 14B .
B1405 Power Window Driver Down
Circuit Short to Battery GEM GO to
Pinpoint Test D for convertible or
Pinpoint Test E for coupe.
B1408 Power Window Driver Up
Circuit Short to Battery GEM GO to
Pinpoint Test D for convertible or
Pinpoint Test E for coupe.
B1410 Power Window Driver Motor
Circuit Failure GEM GO to
Pinpoint Test D for convertible or
Pinpoint Test E for coupe.
B1426 Lamp Safety Belt Circuit
Short to Battery GEM REFER to
Section 413 - 01 .
B1428 Lamp Safety Belt Circuit
Failure GEM REFER to
Section 413 - 01 .
B1431 Wiper Brake/run Relay Circuit
Failure GEM GO to
Section 501 - 16 .
B1432 Wiper Brake/run Relay Circuit
Short to Battery GEM GO to
Section 501 - 16 .
B1434 Wiper High/low Speed Relay
Coil Circuit Failure GEM GO to
Section 501 - 16 .
B1436 Wiper High/low Speed Relay
Coil Circuit Short to Battery GEM GO to
Section 501 - 16 .
B1438 Wiper Mode Select Switch
Circuit Failure GEM GO to
Section 501 - 16 .
B1441 Wiper Mode Select Switch
Circuit Short to Ground GEM GO to
Section 501 - 16 .
B1446 Wiper Park Sense Circuit
Failure GEM GO to
Section 501 - 16 .
B1448 Wiper Park Sense Circuit
Short to Battery GEM GO to
Section 501 - 16 . Klj . 3 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

B1450 Wiper Wash/delay Switch
Circuit Failure GEM GO to
Section 501 - 16 .
B1453 Wiper Wash/delay Switch
Circuit Short to Ground GEM GO to
Section 501 - 16 .
B1458 Wiper Washer Pump Motor
Relay Circuit Failure GEM GO to
Section 501 - 16 .
B1460 Wiper Washer Pump Motor
Relay Circuit Short to Battery GEM GO to
Section 501 - 16 .
B1462 Safety Belt Switch Circuit
Failure GEM GO to
Section 413 - 09 .
B1466 Wiper High/low Speed Not
Switching GEM GO to
Section 501 - 16 .
B1473 Wiper Low Speed Circuit
Motor Failure GEM GO to
Section 501 - 16 .
B1476 Wiper High Speed Circuit
Motor Failure GEM GO to
Section 501 - 16 .
B1498 Decklid Punch-
out Sensor
Ground Short GEM GO to
Section 419 - 01 .
B1551 Decklid Release Circuit
Failure GEM GO to
Section 501 - 14B .
B1553 Decklid Release Circuit Short
to Battery GEM GO to
Section 501 - 14B .
B1555 Ignition RUN/START Circuit
Failure GEM GO to
Section 211 - 05 .
B1603 Lamp Anti-
Theft Indicator
Circuit Failure GEM GO to
Section 419 - 01 .
B1605 Lamp Anti-
Theft Indicator
Circuit Short to Battery GEM GO to
Section 419 - 01 .
B1687 Lamp Dome Input Circuit
Short to Battery GEM GO to
Section 417 - 02 .
B1833 Door Unlock Disarm Switch
Circuit Short to Ground GEM GO to
Section 419 - 01 .
B2486 Parklamp Output Relay Driver
Circuit Failure GEM GO to
Section 419 - 01 .
B2488 Parklamp Output Relay Driver
Circuit Short to Battery GEM GO to
Section 419 - 01 .
C1189 Brake Fluid Level Sensor
Input Circuit Short to Ground GEM REFER to
Section 413 - 01 .
C1223 Lamp Brake Warning Output
Circuit Failure GEM REFER to
Section 413 - 01 .
C1225 Lamp Brake Warning Output
Circuit Short to Battery GEM REFER to
Section 413 - 01 .
ICM DIAGNOSTIC TROUBLE CODE (DTC) INDEX DTC Description Source Action
B1343 Heated Backlight Input Circuit Failure ICM GO to
Pinpoint Test H . Klj . 4 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST H: THE DEFROST SYSTEM IS INOPERATIVE G5 CHECK DRIVER WINDOW REGULATOR CONTROL SWITCH
z
Disconnect: Driver Window Regulator Control Switch C537.
z Carry out the driver window regulator control switch component test.
REFER to Wiring Diagrams Cell 149, Component Testing.
z Is the driver window regulator control switch OK? Yes
INSTALL a new
rear window
regulator motor.
REFER to
Motor —
Window Regulator,
Quarter in this
section. TEST the
system for normal
operation.
No
INSTALL a new
driver window
regulator control
switch. REFER to
Switch — Window
Regulator Control in
this section. TEST
the system for
normal operation. Test Step Result / Action to Take
H1 CHECK POWER TO INDICATOR LIGHT
z
Key in ON position.
z Depress the rear window defrost switch to ON.
z Is the rear window defrost switch indicator ON? Yes
GO to
H2 .
No
GO to H3 .
H2 CHECK CIRCUIT 186 (BR/LB) FOR AN OPEN
z
Key in OFF position.
z Disconnect: Heated Rear Window Relay.
z Disconnect: Heated Rear Window Grid Power Supply
Connector C402a.
z Measure the resistance between heated rear window relay,
circuit 186 (BN/LB), harness side and heated rear window
grid C402a, circuit 186 (BN/LB), harness side.
z Is the resistance less than 5 ohms? Yes
GO to
H7 .
No
REPAIR the circuit. TEST
the system for normal
operation. H3 CHECK THE DIAGNOSTIC TROUBLE CODES (DTCS)
z
Refer to the results from the previous instrument cluster
module (ICM) self- test.
z Was DTC B1343 retrieved? Yes
GO to
H4 . Klj . 25 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Disconnect: Heated Rear Window Grid Ground Connector
C402b.
z Measure the resistance between heated rear window grid
C402b, circuit 1205 (BK), harness side and ground.
z Is the resistance less than 5 ohms? CARRY OUT the heated
rear window grid wire test.
REFER to Grid Wire Test
in Component Tests in this
section. TEST the system
for normal operation.
No
REPAIR the circuit. TEST
the system for normal
operation.
H8 CHECK CIRCUIT 727 (YE/BK)
z
Disconnect: Heated Rear Window Relay.
z Depress the rear window defrost switch to ON.
z Measure the resistance between heated rear window relay
pin 85, circuit 727 (YE/BK), harness side and ground.
z Is the resistance less than 5 ohms? Yes
GO to
H9 .
No
GO to H11 .
H9 CHECK CIRCUIT 185 (BK) FOR POWER
z
Measure the voltage between heated rear window relay pin
86 and pin 30, circuit 185 (BK), harness side and ground.
z Are the voltages greater than 10 volts? Yes
GO to
H10 .
No
REPAIR the supply circuit.
TEST the system for
normal operation. H10 CHECK CIRCUIT 186 (BR/LB) FOR AN OPEN
z
Using a fused jumper wire (15A), jumper across the heated
rear window relay pin 30, circuit 185 (BK), harness side and
the heated rear window relay pin 87, circuit 186 (BR/LB),
harness side. Yes
INSTALL a new heated
rear window relay. TEST
the system for normal
operation.
No
REPAIR circuit 186 Klj . 27 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the rear window defrost switch indicator ON? (BR/LB). TEST the system
for normal operation.
H11 CHECK ICM OUTPUT
z
Trigger the ICM active command R DEFRLY to ON.
z Measure the resistance between the heated rear window
relay pin 85, circuit 727 (YE/BK), harness side and ground.
z Is the resistance less than 5 ohms? Yes
GO to
H13 .
No
GO to H12 .
H12 CHECK CIRCUIT 727 (YE/BK) FOR AN OPEN
z
Key in OFF position.
z Measure the resistance between ICM C220a pin 10, circuit
727 (YE/BK), harness side and the heated rear window relay
pin 85, circuit 727 (YE/BK) , harness side.
z Is the resistance less than 5 ohms? Yes
GO to
H16 .
No
REPAIR the circuit. TEST
the system for normal
operation. H13 CHECK POWER TO REAR WINDOW DEFROST SWITCH
z
Disconnect: Rear Window Defrost Switch C241.
z Key in ON position.
z Measure the voltage between the rear window defrost switch
C241 pin 1, circuit 883 (PK/LB), harness side and ground. Yes
GO to
H14 .
No
REPAIR the supply circuit.
TEST the system for
normal operation. Klj . 28 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST I: THE DEFROST SYSTEM WILL NOT SHUT OFF
AUTOMATICALLY caused by a loose or
corroded connector.
CLEAR the DTCs.
REPEAT the self-
test. Test Step Result / Action to Take
I1 CHECK CIRCUIT 727 (YE/BK)
z
Disconnect: Heated Rear Window Relay.
z Key in ON position.
z Depress the rear window defroster switch to OFF.
z Measure the resistance between heated rear window
relay pin 85, circuit 727 (YE/BK) , harness side and
ground.
z Is the resistance greater than 10,000 ohms? Yes
GO to
I3 .
No
GO to I2 .
I2 CHECK CIRCUIT 727 (YE/BK) FOR A SHORT TO
GROUND z
Key in OFF position.
z Measure the resistance between instrument cluster
module (ICM) C220a pin 10, circuit 727 (YE/BK) ,
harness side and ground.
z Is the resistance greater than 10,000 ohms? Yes
GO to
I4 .
No
REPAIR the circuit. TEST the
system for normal operation. I3 CHECK CIRCUIT 186 (BN/LB) FOR A SHORT TO POWER
z
Disconnect: Heated Rear Window Grid Power Supply
Connector C402a.
z Measure the voltage between heated rear window grid
C402a circuit 186 (BN/LB), harness side and ground. Yes
REPAIR the circuit. TEST the
system for normal operation.
No
INSTALL a new heated rear
window relay. TEST the
system for normal operation. Klj . 30 ba
322003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Keyless Entry
Refer to Wiring Diagrams Cell
59 , Generic Electronic Module for schematic and connector
information.
Refer to Wiring Diagrams Cell 111 , Remote Keyless Entry (RKE) for schematic and connector
information.
Principles of Operation
NOTE: Battery power and ground must be remove before disconnecting the GEM connectors to avoid
setting false codes.
Power Locks Operation
The power locks feature allows the customer to lock and unlock the doors via momentary switches
located on the driver and passenger door. When the GEM detects a momentary press of the driver or
passenger lock button, the GEM will supply power to the driver or passenger lock actuators for
approximately 250 ms from relays internal to the GEM. When the GEM detects a momentary press of
the driver or passenger unlock button, the GEM will supply power to the driver or passenger unlock
actuators for approximately 250 ms from relays internal to the GEM.
Remote Keyless Entry Door Locks Operation
The remote entry feature allows the customer to unlock the driver door, unlock all doors, and lock all
doors using a valid remote transmitter as long as the ignition switch is not in RUN or START. The
driver door is unlocked whenever the GEM detects a valid remote transmitter unlock transmission. All
the doors are unlocked when the GEM detects a second valid remote transmitter unlock transmission
within three seconds of the first transmission. All the doors are locked when the GEM detects a valid
remote transmitter lock transmission. If the GEM detects a second valid remote transmitter lock
transmission within three seconds of the first transmission, the doors will lock again, the horn will
sound for 20 ms and the parking lamps will flash for 200 ms to indicate the doors are locked. If the
GEM detects the driver or passenger door is ajar during the second lock transmission, the doors are
locked again and the horn is sounded twice. If the GEM detects a valid remote transmitter lock
transmission within three seconds of detecting a valid remote transmitter unlock transmission, the SECTION 501-
14B: Keyless Entry/Computer Operated Locks 2003 Mustang Workshop Manual Special Tool(s)
73 Digital Multimeter or
equivalent
105-
R0051 Worldwide Diagnostic System
(WDS)
418-
F224
New Generation STAR (NGS)
Tester
418- F052, or equivalent scan
tool Klj . 1 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

4. If the concern remains after the inspection, connect the scan tool to the data link connector
(DLC) located beneath the instrument panel and select the vehicle to be tested from the scan
tool menu. If the scan tool does not communicate with the vehicle:
zcheck that the program card is correctly installed.
z check the connections to the vehicle.
z check the ignition switch position.
5. If the scan tool still does not communicate with the vehicle, refer to the scan tool manual.
6. Carry out the DATA LINK DIAGNOSTIC TEST. If the scan tool responds with: zCKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418 -
00 .
z NO RESP/NOT EQUIP for GEM, go to Pinpoint Test A.
z SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs, and carry out the self- test diagnostics for the GEM.
7. If the DTCs retrieved are related to the concern, go to the GEM Diagnostic Trouble Code (DTC) Index to continue diagnostics.
8. If no DTCs related to the concern are retrieved, proceed to Symptom Chart to continue diagnostics.
GEM Diagnostic Trouble Code (DTC) Index Mechanical Electrical
z
Binding latches z
CJB Fuses:
„39 (5A)
„ 19 (15A)
„ 25 (25A)
z BJB Fuse POWER WINDOWS (40A)
z Damaged wiring harness
z Loose or corroded connector(s)
z Circuitry open/shorted
z Damaged relays
z Remote transmitter
z Remote transmitter batteries DTC Description Source Action
B1217 Horn Relay Coil Circuit Failure GEM GO to
Pinpoint Test E .
B1218 Horn Relay Coil Circuit Short to
Vbatt GEM GO to
Pinpoint Test E .
B1312 Lamp Headlamp Input Circuit
Short to Battery GEM REFER to
Section 417 - 01 .
B1317 Battery Voltage High GEM REFER to
Section 414 - 00 .
B1318 Battery Voltage Low GEM REFER to
Section 414 - 00 .
B1322 Driver Door Ajar Circuit Short to
Ground GEM REFER to
Section 417 - 02 .
B1330 Passenger Door Ajar Circuit
Short to Ground GEM REFER to
Section 417 - 02 .
B1334 Decklid Ajar Rear Door Circuit GEM REFER to
Section 417 - 02 . Klj . 3 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...