pinpoint test b FORD MUSTANG 2003 Repair Manual

PINPOINT TEST B: UNABLE TO ENTER SELF-
TEST
PINPOINT TEST C: DTC B1318, BATTERY VOLTAGE LOW z
Is the voltage greater than 10 volts? REPEAT the self-
test.
A2 CHECK THE ANTI-
LOCK BRAKE CONTROL MODULE GROUNDS z
Measure the resistance between anti- lock brake control module
C141 Pin 12, Circuit 1205 (BK), harness side and ground; and
between anti- lock brake control module C141 Pin 15, Circuit 397
(BK/WH), harness side and ground.
z Are the resistances less than 5 ohms? Yes
INSTALL a new
anti-
lock brake
control module;
REFER to Module .
REPEAT the self-
test.
No
REPAIR the circuit
in question.
REPEAT the self-
test. Test Step Result / Action to Take
B1 CHECK THE COMMUNICATIONS TO THE
ANTI- LOCK BRAKE CONTROL MODULE z
Check the communications to the anti- lock
brake control module.
z Does the scan tool communicate with the
anti-lock brake control module? Yes
INSTALL a new anti-
lock brake control
module; REFER to Module . REPEAT the
self- test.
No
Go To Pinpoint Test A .
Test Step Result / Action to
Take C1 CHECK BATTERY VOLTAGE
z
Measure the battery voltage between the positive and negative
battery posts with the key ON engine OFF (KOEO), and with the
engine running. Yes
GO to
C2 .
No
REFER to Section Klj . 7 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST D: DTC B1484, BRAKE PEDAL INPUT OPEN
CIRCUIT z
Is the battery voltage between 10 and 13 volts with KOEO, and
between 11 and 17 volts with the engine running? 414 - 00 .
C2 CHECK THE VOLTAGE TO THE ANTI-
LOCK BRAKE CONTROL
MODULE z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C141.
z Key in ON position.
z Measure the voltage between anti- lock brake control module C141
Pin 8, Circuit 601 (LB/PK), harness side and ground.
z Is the voltage greater than 10 volts? Yes
GO to
C3 .
No
REPAIR the circuit.
CLEAR the DTCs.
REPEAT the self-
test. C3 CHECK THE ANTI-
LOCK BRAKE CONTROL MODULE GROUNDS z
Measure the resistance between anti- lock brake control module
C141 Pin 12, Circuit 1205 (BK), harness side and ground; and
between anti- lock brake control module C141 Pin 15, Circuit 397
(BK/WH), harness side and ground.
z Are the resistances less than 5 ohms? Yes
INSTALL a new
anti-
lock brake
control module;
REFER to Module .
REPEAT the self-
test.
No
REPAIR the circuit
in question.
CLEAR the DTCs.
REPEAT the self-
test. Test Step Result / Action to Take
D1 CHECK THE STOPLAMPS FOR CORRECT OPERATION Klj . 8 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST E: DTC C1095, ABS HYDRAULIC PUMP MOTOR
FAILURE z
Depress the brake pedal while checking the stoplamps.
z Do the stop lamps illuminate? Yes
GO to
D2 .
No
REFER to Section 417 -
01 .
D2 CHECK THE BRAKE PEDAL INPUT TO THE ANTI-
LOCK
BRAKE CONTROL MODULE z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C141.
z Measure the voltage between anti- lock brake control module
C141 Pin 6, Circuit 511 (LG), harness side and ground, while
depressing and releasing the brake pedal.
z Is the voltage greater than 10 volts with the brake pedal
depressed and zero volts with the brake pedal released? Yes
INSTALL a new anti-
lock
brake control module;
REFER to Module .
REPEAT the self- test.
No
REPAIR Circuit 511 (LG)
and Circuit 810 (RD/LG)
as necessary. CLEAR
the DTCs. REPEAT the
self- test. Test Step Result / Action to
Take E1 CHECK THE PUMP MOTOR FOR CONTINUOUS OPERATION
z
Check the pump motor for continuous operation.
z Is the pump motor running continuously? Yes
INSTALL a new
anti-
lock brake
control module;
REFER to Module .
REPEAT the self-
test.
No
GO to E2 .
E2 CHECK CIRCUIT 534 (YE/LG) FOR AN OPEN
z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C141.
z Measure the voltage between anti- lock brake control module C141
Pin 13, Circuit 534 (YE/LG), harness side, and ground. Yes
GO to
E3 .
No
REPAIR the circuit.
CLEAR the DTCs.
REPEAT the self-
test. Klj . 9 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST F: DTC C1145 (RF), C1155 (LF), C1165 (RR), C1175
(LR), ANTI-
LOCK BRAKE SENSOR INPUT CIRCUIT FAILURE z
Is the voltage greater than 10 volts? E3 CHECK CIRCUIT 1205 (BK) FOR AN OPEN
z
Measure the resistance between anti- lock brake control module
C141 Pin 12, Circuit 1205 (BK), harness side and ground.
z Is the resistance less than 5 ohms? Yes
GO to
E4 .
No
REPAIR the circuit.
CLEAR the DTCs.
REPEAT the self-
test. E4 CHECK THE PUMP MOTOR FOR OPERATION
z
Disconnect: Pump Motor Connector.
z Connect a 30A fused heavy jumper wire between the positive battery
post and pump motor connector Pin 1 (component side); and
momentarily connect a heavy jumper between negative battery post
and pump motor connector Pin 2 (component side).
z Does the pump motor operate? Yes
INSTALL a new
anti-
lock brake
control module;
REFER to Module .
REPEAT the self-
test.
No
INSTALL a new
HCU; REFER to
Hydraulic Control Unit . CLEAR the
DTCs. REPEAT
the self- test. Test Step Result / Action to Take
F1 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR CIRCUIT FOR SHORT TO POWER z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C141.
z Key in ON position. Yes
REPAIR the circuit in question.
CLEAR the DTCs. REPEAT the self- Klj . 10 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST G: DTC C1222, ANTI-
LOCK BRAKE SENSOR
MISMATCH z
Are the resistances less than 5 ohms? (RR)
C1175
(LR) C141 Pin 22 C320 Pin 2 496 (OG)
C1175
(LR) C141 Pin 23 C320 Pin 1 499
(GY/BK) F5 CHECK THE ANTI-
LOCK BRAKE SENSOR z
Measure the resistance between suspect anti- lock
brake sensor pin 1 (component side) and suspect
anti- lock brake sensor pin 2 (component side).
z Is the resistance between 1280 and 1920 (front)
or 1830 and 2760 (rear) ohms? Yes
INSTALL a new anti-
lock brake
control module; REFER to Module .
REPEAT the self- test.
No
INSTALL a new anti- lock brake
sensor; REFER to Sensor — Front or
Sensor — Rear . CLEAR the DTCs.
REPEAT the self- test. Test Step Result / Action to Take
G1 CHECK THE VEHICLE
COMPONENTS z
Check for correct wheel and tire
size, front- to-rear and side- to-
side.
z Check for excessive bearing end
play.
z Check the anti- lock brake sensor
indicator for a bent sensor ring or
missing teeth.
z Are the conditions OK? Yes
GO to
G2 .
No
REPAIR as necessary. CLEAR the DTCs. REPEAT
the self- test. G2 TEST DRIVE THE VEHICLE
z
Enter the following diagnostic Yes Klj . 13 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST H: DTC C1233 (LF), C1234 (RF), C1235 (RR), C1236
(LR), ANTI-
LOCK BRAKE SENSOR INPUT SIGNAL MISSING
PINPOINT TEST I: THE YELLOW ABS WARNING INDICATOR DOES
NOT SELF- CHECK mode on the diagnostic tool:
CLEAR the DTCs.
z Key in OFF position.
z Key in ON position.
z Test drive the vehicle over 24
km/h (15 mph).
z Enter the following diagnostic
mode on the diagnostic tool:
Retrieve DTCs.
z Is DTC C1222 retrieved? INSTALL a new anti-
lock brake control module;
REFER to Module . REPEAT the self-
test.
No
If another DTC is retrieved, GO to the Anti- Lock Brake
Control Module Diagnostic Trouble Code (DTC) index.
If no DTCs are retrieved, system is OK. Test Step Result / Action to Take
H1 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR z
Check the suspect anti- lock brake sensor
mounting.
z Check the suspect anti- lock brake sensor for
excessive dirt build up, obstructions, and
damage.
z Is the suspect anti- lock brake sensor and
mounting OK? Yes
GO to
H2 .
No
REPAIR as necessary. CLEAR the
DTCs. REPEAT the self- test. H2 CHECK THE SUSPECT ANTI-
LOCK BRAKE
SENSOR INDICATOR z
Check the suspect anti- lock brake sensor
indicator for corrosion, nicks, bridged teeth,
damaged teeth, correct mounting, and
alignment with the anti- lock brake sensor.
z Check the air gap and bearing end play.
z Is the suspect anti- lock brake sensor
indicator OK? Yes
GO to
H3 .
No
INSTALL a new anti- lock brake sensor
indicator; REFER to Sensor Indicator —
Front or
Sensor Indicator — Rear .
CLEAR the DTCs. REPEAT the self- test. H3 CHECK THE ANTI-
LOCK BRAKE SENSOR
OUTPUT z
Key in ON position.
z Enter the following diagnostic mode on the
diagnostic tool: CLEAR the DTCs.
z Key in OFF position.
z Key in ON position.
z Have an assistant monitor the anti- lock brake
control module PIDs LF_WSPD, RF_WSPD,
LR_WSPD, and RR_WSPD while driving at
various speeds.
z NOTE: the vehicle must be driven 16 km (10
miles) during this test step.
z Test drive the vehicle for 16 km (10 miles).
z Are the anti- lock brake control module PIDs
approximately the same at all times? Yes
INSTALL a new anti-
lock brake control
module; REFER to Module . REPEAT
the self- test.
No
INSTALL a new anti- lock brake sensor;
REFER to Sensor — Front or
Sensor —
Rear . CLEAR the DTCs. REPEAT the
self- test. Klj . 14 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST J: SPONGY BRAKE PEDAL WITH NO WARNING
INDICATOR
PINPOINT TEST K: POOR VEHICLE TRACKING DURING ANTI-
LOCK
FUNCTION Test Step Result / Action to Take
I1 CHECK THE ABS WARNING INDICATOR CIRCUITRY
z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C141.
z Key in ON position.
z Depress and release the shorting bar connector
internal to the anti- lock brake control module C141,
harness side, while checking the yellow ABS warning
indicator in the instrument cluster.
z Does the yellow ABS indicator illuminate with the
shorting bar released and OFF with the shorting
bar depressed? Yes
INSTALL a new anti-
lock brake
control module; REFER to
Module . TEST the system for
normal operation.
No
REFER to Section 413 - 01 .
Test Step Result / Action to Take
J1 CHECK THE VEHICLE COMPONENTS
z
Check the brake pedal and power
booster/brake master cylinder for correct
attachment.
z Are the components OK? Yes
GO to
J2 .
No
REPAIR as necessary. TEST the system for
normal operation. J2 BLEED THE BRAKE SYSTEM
z
Bleed the brake system; REFER to Section 206 - 00 .
z Check for spongy brake pedal.
z Is the brake pedal spongy? Yes
INSTALL a new HCU; REFER to
Hydraulic Control Unit . TEST the system for normal
operation.
No
The brake system is OK. TEST the system
for normal operation. Test Step Result / Action to Take
K1 BLEED THE BRAKE SYSTEM
z
Bleed the brake system; REFER to Section 206 - 00 .
z Check for vehicle tracking poorly.
z Does the vehicle track poorly? Yes
GO to
K2 .
No
The brake system is OK. TEST the
system for normal operation. K2 CHECK THE LF ABS VALVE OPERATION
z
Lift the vehicle and rotate all the wheels to
make sure they rotate freely (the vehicle must
be in neutral).
z NOTE: Trigger must be depressed twice.
Each depress runs the pump motor for two
seconds. Yes
INSTALL a new HCU; REFER to
Hydraulic Control Unit
. TEST the system
for normal operation.
No Klj . 15 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST L: THE TRACTION CONTROL IS INOPERATIVE—
DOES NOT OPERATE CORRECTLY K8 CHECK THE RR ABS VALVE OPERATION
z
NOTE: Trigger must be depressed twice.
Each depress runs the pump motor for two
seconds.
z Trigger the anti- lock brake control module
active command PMP MOTOR ON for four
seconds.
z Apply moderate brake pedal effort.
z Have an assistant attempt to rotate the RR
wheel while the pump motor is running.
z Does the RR wheel rotate? Yes
INSTALL a new HCU; REFER to
Hydraulic Control Unit
. TEST the system
for normal operation.
No
GO to K9 .
K9 CHECK THE RR ABS VALVE RELEASE
z
Apply moderate brake pedal effort.
z Trigger the anti- lock brake control module
active command RF INLET and RF OUTLET.
z NOTE: The scan tool will energize the valves
for only two seconds per trigger press.
z Have an assistant rotate the RR wheel
immediately after depressing trigger.
z Does the RR wheel rotate? Yes
The ABS system is operating correctly.
No
GO to
K10 .
K10 CHECK FOR DTCS
z
Carry out the anti- lock brake control module
self- test.
z Are any DTCs retrieved? Yes
GO to the Anti-
Lock Brake Control Module
Diagnostic Trouble Code (DTC) Index.
No
INSTALL a new HCU; REFER to
Hydraulic Control Unit . TEST the system
for normal operation. Test Step Result / Action to Take
L1 CHECK THE TRACTION CONTROL SWITCH CIRCUITRY
z
Key in OFF position.
z Disconnect: Instrument Cluster C251.
z Key in ON position.
z Measure the voltage between instrument cluster C251 Pin 9,
Circuit 959 (GY), harness side and ground, while depressing
and releasing the traction control switch.
z Is the voltage greater than 10 volts with the traction control
switch depressed and zero volts with the traction control
switch released? Yes
INSTALL a new
instrument cluster,
REFER to
Section 413 -
01 . TEST the system
for normal operation.
No
GO to L2 . Klj . 17 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

PINPOINT TEST M: THE TRACTION CONTROL INDICATOR IS
INOPERATIVE—
TRACTION CONTROL SWITCH L2 CHECK CIRCUIT 959 (GY) FOR AN OPEN
z
Key in OFF position.
z Disconnect: Traction Control Switch C239.
z Measure the resistance between instrument cluster C251 Pin 9,
Circuit 959 (GY), harness side and traction control switch C239
Pin 4, Circuit 959 (GY), harness side.
z Is the resistance less than 5 ohms? Yes
GO to
L3 .
No
REPAIR the circuit.
TEST the system for
normal operation. L3 CHECK CIRCUIT 489 (PK/BK) FOR AN OPEN
z
Key in ON position.
z Measure the voltage between traction control switch C239 Pin
3, Circuit 489 (PK/BK), harness side and ground.
z Is the voltage greater than 10 volts? Yes
INSTALL a new traction
control switch. TEST the
system for normal
operation.
No
REPAIR the circuit.
TEST the system for
normal operation.
Test Step Result / Action to
Take M1 CHECK CIRCUIT 960 (BK/LB)
z
Key in OFF position.
z Disconnect: Instrument Cluster C251.
z Disconnect: Traction Control Switch C239.
z Measure the resistance between instrument cluster C251 Pin 8,
Circuit 960 (BK/LB), harness side and traction control switch C239
Pin 5, Circuit 960 (BK/LB), harness side; and between instrument
cluster C251 Pin 8, Circuit 960 (BK/LB), harness side and ground. Yes
GO to
M2 .
No Klj . 18 ba
202003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
check the connections to the vehicle.
z check the ignition switch position.
4. If the scan tool still does not communicate with the vehicle, refer to the scan tool manual.
5. Carry out the DATA LINK DIAGNOSTIC TEST. If the scan tool responds with: zCKT914, CKT915 or CKT70 =ALL ECUS NO RESP/NOT EQUIP, refer to Section 418 -
00 .
z NO RESP/NOT EQUIP for GEM, go to Pinpoint Test A.
z SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs and carry out self- test diagnostics for the GEM.
6. If the DTCs retrieved are related to the concern, go to the GEM Diagnostic Trouble Code (DTC) Index to continue diagnostics.
7. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.
GEM Diagnostic Trouble Code (DTC) Index GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action
B1217 Horn Relay Coil Circuit Failure GEM REFER to
Section 413 - 06 .
B1218 Horn Relay Coil Circuit Short to
Vbatt GEM REFER to
Section 413 - 06 .
B1312 Lamp Headlamp Input Circuit
Short to Battery GEM REFER to
Section 417 - 01 .
B1317 Battery Voltage High GEM REFER to
Section 414 - 00 .
B1318 Battery Voltage Low GEM REFER to
Section 414 - 00 .
B1322 Driver Door Ajar Circuit Short to
Ground GEM REFER to
Section 417 - 02 .
B1330 Passenger Door Ajar Circuit
Short to Ground GEM REFER to
Section 417 - 02 .
B1334 Decklid Ajar Rear Door Circuit
Short to Ground GEM REFER to
Section 417 - 02 .
B1339 Chime Input Request Circuit
Short to Battery GEM REFER to
Section 413 - 09 .
B1340 Chime Input Request Circuit
Short to Ground GEM REFER to
Section 413 - 09 .
B1342 ECU Is Defective GEM CLEAR the DTC. Retrieve the DTCs. If DTC
B1342 is retrieved, INSTALL a new GEM. REFER to Section 419 - 10 .
B1353 Ignition Key-
In Circuit Open GEM REFER to
Section 413 - 09 .
B1359 Ignition Run/Acc Circuit Failure GEM GO to
Pinpoint Test E .
B1396 Power Door Lock Circuit Short
to Battery GEM REFER to
Section 501 - 14B .
B1397 Power Door Unlock Circuit
Short to Battery GEM REFER to
Section 501 - 14B . Klj . 2 ba
82003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...