FORD MUSTANG 2003 Repair Manual

glass
zAir traveling up
windshield molding
along A- pillar. z
INSTALL foam rope the
full length of the A- pillar.
z Windshield/backlite
misaligned or not
installed correctly. z
REINSTALL the
windshield/backlite.
z Rear hood seal at base
of windshield
misaligned/damaged. z
REALIGN or INSTALL a
new seal as necessary.
z Air leak at cowl zCowl gasket
misaligned/damaged. z
REALIGN or INSTALL a
new seal as necessary.
z Air leak around
liftgate perimeter z
Loose fit seal. zPINCH the seal carrier to
improve retention on the
seal flange or INSERT
foam in the carrier.
z Seal misaligned. zREINSTALL the seal.
z Liftgate misaligned. zREALIGN the liftgate.
CHECK the liftgate fit in
the body opening and
ADJUST as necessary.
z Scuff plate misaligned. zREINSTALL the scuff
plate.
z Seal or seal push pins
damaged. z
INSTALL a new seal.
z Air leak around
the liftgate flip
window
perimeter z
Loose fit seal. zPINCH the seal carrier to
improve the retention to
the seal flange.
z Seal misaligned. zREINSTALL the seal.
z Glass misaligned. zREALIGN the glass.
z Seal damaged. zINSTALL a new seal.
z Wind noise from
antenna z
Shape of antenna. zINSTALL an antenna boot
or a spiral antenna.
z Air leak around
antenna cable access
hole. z
INSPECT the antenna
access hole grommet.
REPAIR as necessary.
z Air leak from
closed roof
opening panel z
Seal installed
incorrectly. z
REINSTALL the seal.
z Roof opening panel
glass/door misaligned. z
REALIGN the roof
opening panel glass/door.
z Roof opening panel
damaged. z
INSTALL a new roof
opening panel.
z Buffeting from an
open roof
opening panel z
Wind deflector
inoperative/damaged. z
REPAIR or INSTALL a
new wind deflector as
necessary.
z Wind deflector height
incorrect. z
ADJUST the wind
deflector higher.
z Wind noise
created by
airflow over or
behind body
panels z
Fender splash shield
misaligned. z
REALIGN the fender
splash shield. Klj . 14 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Body panel misaligned
(exposed edge). z
REALIGN the appropriate
body panel.
z Hood misaligned (front
margin). z
CHECK hood gaps and fit.
ADJUST the hood as
necessary.
z Front grille edge noise. zAPPLY foam in the hollow
areas behind the louvers.
z Wind noise
created by grille
opening panel z
Grille relationship to
leading edge on hood. z
ADJUST the grille
opening panel forward to
eliminate wind noise.
z Sharp edges due to
material imperfections. z
REMOVE the sharp
edges (no damage to
visible surface).
z Wind noise from
air extractor z
Air extractor housing
seated incorrectly. z
REINSTALL the air
extractor housing.
z Air extractor housing or
flaps damaged. z
INSTALL a new air
extractor.
z Air leak at top of
A-pillar —
vehicles with a
convertible top z
Seal at windshield
header installed
incorrectly. z
REINSTALL the seal.
z Seal pinched. zFILL the seal with foam to
reshape it.
z Gap between side rail
and header seal at A-
pillar. z
ADJUST the J-hook/vinyl
top.
z Air leak at rear
quarter glass
(division bar) —
vehicles with a
convertible top z
No contact between
front side glass and
quarter glass division
bar. z
ADJUST the front side
glass regulator and the
rear quarter glass
regulator.
z Air leak or wind
noise from top of
side glass —
vehicles with a
convertible top z
Gap between side rail
and vinyl top. z
ADD additional foam tape
to seal between the side
rail and the vinyl top.
z Seal at windshield
header installed
incorrectly. z
REINSTALL the seal.
z Seal damaged
between side rail and
vinyl top. z
INSTALL a new seal.
z Vinyl top damaged. zINSPECT the vinyl top.
INSTALL a new vinyl top
as necessary.
z Air leak or wind
noise at
windshield
header —
vehicles with a
convertible top z
Vinyl top not flush with
header. z
ADJUST the J-hook to
lower the top to achieve a
flush condition.
z Seal at windshield
header installed
incorrectly. z
REINSTALL the seal.
z Header seal not flush zREINSTALL the seal. Klj . 15 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

with header.
z Convertible top
flapping with the
top up z
Vinyl top contacting
interior headliner. z
Working from front to
back, INSTALL a 6.35 mm
(0.25 in) foam sheet
between the headliner
and the vinyl top at the
suspected area. Allow a
clearance of 50 mm (2 in)
-75 mm (3 in) away from
the roof bows and the side
rails.
z Noise from roof
rack z
Roof rack rails or
crossbars loose. z
TIGHTEN the fasteners.
z Roof rack fasteners
missing. z
INSTALL the approved
fasteners.
z Roof rack crossbars
installed backward. z
REINSTALL the
crossbars.
z Roof rack rub strips
partially lifting from
roof. z
REAPPLY adhesive or
fasteners or INSTALL new
rub strips as necessary.
z Roof rack gaskets
loose or misaligned. z
REINSTALL the gasket.
z Wind noise from
bug
shield/exterior
windshield sun
visor z
Turbulence created by
location and shape. z
REMOVE per customer
direction if it is a dealer
installed option. Symptom Chart—
Brake Noise/Vibration Condition
Possible Sources Action
z Rattling noise zCaliper
mounting bolts
loose. z
CHECK the caliper bolts.
TIGHTEN to specifications.
REFER to Section 206 - 03
for front disc brakes or
Section 206
- 04 for rear
disc brakes.
z Damaged or
worn caliper
pins or
retainers. z
CHECK the caliper pins
and retainers for lubrication
and correct fit. LUBRICATE
or INSTALL new
components as necessary.
z Missing or
damaged anti-
rattle clips or
springs. z
CHECK the brake pads for
missing clips or broken
springs. INSTALL new
components as necessary.
REFER to Section 206 - 03
for front disc brakes or
Section 206
- 04 for rear
disc brakes.
z Loose brake
disc shield. z
TIGHTEN the brake disc
shield bolts to specification.
REFER to Section 206 - 03 .
z Clicking noise— with
brakes applied with
ABS brakes z
ABS hydraulic
control unit. z
Acceptable condition.
z Squealing noise— zDisc brake zAcceptable condition. Klj . 16 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

occurs on first
(morning) brake
application
pads.
Caused by humidity and
low disc brake pad
temperature.
z Squealing noise— a
continuous squeal z
Disc brake pads
or linings worn
below minimum
thickness. z
INSTALL new disc brake
pads. REFER to Section 206 - 03 for front disc brake
pads or Section 206 - 04 for
rear disc brake pads.
z Squealing noise— an
intermittent squeal
brought on by cold,
heat, water, mud or
snow z
Disc brake pad. zAcceptable condition.
z Groaning noise—
occurs at low speeds
with brake lightly
applied (creeping) z
Disc brake
pads. z
Acceptable condition.
z Grinding noise—
continuous z
Disc brake pads
or linings worn
below minimum
thickness. z
INSPECT the disc brake
pads, brake discs and
attaching hardware for
damage. REPAIR or
INSTALL new components
as necessary. REFER to
Section 206 - 03 for front
disc brakes and Section 206 - 04 for rear disc brakes.
z Moaning noise zBrake linings
contaminated
with grease or
oil. z
INSPECT the brake pads
and shoes for
contamination. REPAIR or
INSTALL new components
as necessary. REFER to
Section 206 - 03 for front
disc brakes or Section 206 -
04 for rear disc brakes.
z Brake
vibration/shudder—
occurs when brakes
are applied z
Uneven disc or
drum wear.
z Uneven disc
brake pad or
lining transfer.
z Suspension
components. z
Go To Pinpoint Test A .
z Brake
vibration/shudder—
occurs when the brake
pedal is released z
Brake drag. zINSPECT the disc brake
pads or linings for
premature wear. REPAIR
or INSTALL a new caliper
or wheel cylinder as
necessary. REFER to
Section 206 - 03 for front
disc brakes and Section 206 - 04 for rear disc brakes.
Symptom Chart—
Driveline Noise/Vibration Condition
Possible Sources Action
z Axle howling or
whine— front or rear
axle z
Axle lubricant
low. z
CHECK the lubricant level.
FILL the axle to
specification.
z Axle housing zINSPECT the axle housing Klj . 17 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

damage.
for damage. REPAIR or
INSTALL a new axle as
necessary. REFER to
Section 205 - 02A for Ford
7.5 rear axles or Section 205 - 02B for Ford 8.8
integral axles.
z Damaged or
worn wheel
bearings or axle
bearings. z
CHECK for abnormal wheel
bearing play or roughness.
REFER to Wheel Bearing Check in this section.
ADJUST or INSTALL new
wheel bearings as
necessary.
z Damaged or
worn differential
ring and pinion. z
INSPECT the ring and
pinion ring for abnormal
wear patterns or broken
teeth. INSTALL a new ring
and pinion as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford
8.8 integral axles.
z Damaged or
worn differential
side or pinion
bearings. z
CHECK for abnormal
bearing play or roughness.
INSTALL new bearings as
necessary.
z Damaged or
worn differential
side gears and
pinion gears. z
DISASSEMBLE the
differential carrier. INSPECT
the side and pinion gears for
abnormal wear patterns or
broken teeth. INSTALL new
gears as necessary. REFER
to Section 205 - 02A for Ford
7.5 rear axles or Section 205 - 02B for Ford 8.8
integral axles.
z Driveline clunk— loud
clunk when shifting
from reverse to drive z
Incorrect axle
lubricant level. z
CHECK the lubricant level.
FILL the axle to
specification.
z Excessive
backlash in the
axle or
transmission. z
CARRY OUT a total
backlash check. REFER to
Section 205 - 00 .
z Damaged or
worn pinion
bearings. z
CHECK for abnormal
bearing play or roughness.
INSTALL new bearings as
necessary. REFER to
Section 205 - 02A for Ford
7.5 rear axles or Section 205 - 02B for Ford 8.8
integral axles.
z Damaged or
worn universal
joints (U- joints). z
INSPECT the U- joints for
wear or damage. INSTALL
new U- joints as necessary.
REFER to Section 205 - 01 .
z Loose
suspension
components. z
INSPECT the suspension
for damage or wear.
REPAIR or INSTALL new Klj . 18 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

components as necessary.
z Broken
powertrain
mounts. z
INSPECT the powertrain
mounts. INSTALL new
mounts as necessary.
REFER to Section 303 - 01A
for 3.8L engines or
Section 303 - 01B for 4.6L (2V)
engines.
z Idle speed too
high. z
CHECK for the correct idle
speed.
z Driveline clunk—
occurs as the vehicle
starts to move
forward following a
stop z
Worn or galled
driveshaft slip-
yoke splines. z
CLEAN and INSPECT the
splines of the yoke for a
worn or galled condition.
INSTALL a new yoke as
necessary. REFER to
Section 205 - 01 .
z Worn or galled
driveshaft and
coupling shaft
splines. z
CLEAN and INSPECT the
splines of the driveshaft and
coupling shaft for a worn or
galled condition. INSTALL a
new driveshaft assembly as
necessary. REFER to
Section 205 - 01 .
z Loose rear leaf
spring U- bolts. z
CHECK the U- bolts for
loose nuts. TIGHTEN to
specification. REFER to
Section 204 - 02 .
z Driveline clunk (FWD
vehicles)—occurs
during acceleration or
from cruise to
coast/deceleration z
Damaged or
worn inboard
constant velocity
(CV) joint. z
INSPECT the inboard CV
joint and boot. REPAIR or
INSTALL a new CV joint as
necessary.
z Driveline clunk (4WD
vehicles)—occurs
during shift- on-the- fly
engagement z
Clutch relay.
z Shift motor.
z Transfer case.
z GEM. z
CHECK the 4WD
engagement system.
REPAIR or INSTALL new
components as necessary.
z Clicking, popping or
grinding— occurs
while vehicle is
turning z
Inadequate or
contaminated
lubrication in the
(CV) joints. z
CHECK the CV boots and
joints for wear or damage.
REPAIR or INSTALL new
components as necessary.
z Another
component
contacting the
halfshaft. z
CHECK the halfshafts and
the area around the
halfshafts. REPAIR as
necessary.
z Brake
components. z
INSPECT the front brakes
for wear or damage.
REPAIR as necessary.
REFER to Section 206 - 03 .
z Steering
components. z
INSPECT the drag link,
inner and outer tie- rods or
idler arm for wear or
damage. REPAIR as
necessary. REFER to
Section 211 - 02 .
z Suspension
components. z
INSPECT the upper and
lower ball joints for wear or
damage. REPAIR as
necessary. REFER to Klj . 19 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Section 204 - 01 .
z Damaged or
worn wheel
bearings z
CHECK for abnormal wheel
bearing play or roughness.
Refer to Wheel Bearing Check in this section.
ADJUST or INSTALL new
wheel bearings as
necessary.
z Clicking or
snapping— occurs
when accelerating
around a corner z
Damaged or
worn outboard
CV joint. z
INSPECT the outboard CV
joint and boot. REPAIR or
INSTALL a new CV joint as
necessary.
z High pitched
chattering— noise
from the rear axle
when the vehicle is
turning z
Incorrect or
contaminated
lubricant. z
CHECK the vehicle by
driving in tight circles (5
clockwise, 5
counterclockwise). FLUSH
and REFILL with the
specified rear axle lubricant
and friction modifier as
necessary.
z Damaged or
worn differential
(differential side
gears and pinion
gears). z
DISASSEMBLE the
differential assembly.
INSPECT the differential
case, pin and gears for wear
or damage. REPAIR or
INSTALL a new differential
as necessary. REFER to
Section 205 - 02A for Ford
7.5 rear axles or Section 205 - 02B for Ford 8.8
integral axles.
z Buzz—buzzing noise
is the same at cruise
or coast/deceleration z
Damaged or
worn tires. z
CHECK for abnormal tire
wear or damage. INSTALL a
new tire as necessary.
REFER to Section 204 - 04 .
z Incorrect
driveline angles. z
CHECK for correct driveline
angles. REPAIR as
necessary. REFER to
Section 205 - 00 .
z Rumble or boom—
noise occurs at
coast/deceleration,
usually driveshaft
speed related and
noticeable over a
wide range of speeds z
Driveshaft is
out-of- balance. z
CHECK the driveshaft for
damage, missing balance
weights or undercoating.
CHECK the driveshaft
balance. CARRY OUT a
driveline vibration test.
REFER to Section 205 - 00 .
z U-joints binding
or seized. z
ROTATE the driveshaft and
CHECK for rough operation
or seized U- joints. INSTALL
new U- joints as necessary.
REFER to Section 205 - 01 .
z Excessive
pinion flange
runout. z
CARRY OUT a runout
check. REPAIR as
necessary. REFER to
Section 205 - 00 .
z Grunting— normally
associated with a
shudder experienced
during acceleration z
Driveshaft slip
yoke binding. z
CLEAN and LUBRICATE
the male and female
splines. Klj . 20 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

from a dead stop
zLoose rear
spring U- bolts. z
INSPECT the rear
suspension. TIGHTEN the
U-bolt nuts to specification.
REFER to Section 204 - 02 .
z Howl— can occur at
various speeds and
driving conditions.
Affected by
acceleration and
deceleration z
Incorrect ring
and pinion
contact,
incorrect
bearing preload
or gear damage. z
CHECK the ring and pinion
and bearings for damage.
INSPECT the ring and
pinion wear pattern. REFER
to Checking Tooth Contact
Pattern and Condition of the
Ring and Pinion component
test in this section. ADJUST
or INSTALL new
components as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford
8.8 integral axles.
z Chuckle— heard at
coast/deceleration.
Also described as a
knock z
Incorrect ring
and pinion
contact or by
damaged teeth
on the coast
side of the ring
and pinion. z
CHECK the ring and pinion
for damage. INSPECT the
ring and pinion wear pattern.
REFER to Checking Tooth
Contact Pattern and
Condition of the Ring and
Pinion component test in
this section. ADJUST or
INSTALL new components
as necessary. REFER to
Section 205 - 02A for Ford
7.5 rear axles or Section 205 - 02B for Ford 8.8
integral axles.
z Knock— noise occurs
at various speeds.
Not affected by
acceleration or
deceleration z
Gear tooth
damage to the
drive side of the
ring and pinion. z
CHECK the differential case
and ring and pinion for
damage. INSTALL new
components as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford
8.8 integral axles.
z Excessive axle
shaft end play.
(Vehicles with
integral axles). z
CHECK the axle end play
using a dial indicator.
INSTALL a new axle shaft
or side gears as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford
8.8 integral axles.
z Scraping noise— a
continuous low
pitched noise starting
at low speeds z
Worn or
damaged pinion
bearings. z
CHECK the pinion bearings.
INSTALL new pinion
bearings as necessary.
REFER to Section 205 - 02A
for Ford 7.5 rear axles or
Section 205
- 02B for Ford
8.8 integral axles.
z Driveline shudder—
occurs during
acceleration from a
slow speed or stop z
Rear drive axle
assembly
mispositioned. z
CHECK the axle mounts
and the rear suspension for
damage or wear. REPAIR
as necessary. Klj . 21 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Loose rear
spring U- bolts. z
INSPECT the U- bolts.
TIGHTEN the U- bolt nuts to
specification. REFER to
Section 204 - 02 .
z Incorrect or high
CV joint
operating angle. z
CHECK vehicle ride height
is within limits. REPAIR as
necessary. REFER to
Section 206 - 00 .
z Damaged or
worn front
suspension
components. z
CHECK for a loose stabilizer
bar, damaged or loose
strut/strut bushings or loose
or worn ball joints. INSPECT
the steering linkage for wear
or damage. REPAIR or
INSTALL new components
as necessary.
z Driveline angles
out of
specification. z
CHECK for correct driveline
angles. REPAIR as
necessary. REFER to
Section 205 - 00 .
z U-joints binding
or seized. z
ROTATE the driveshaft and
CHECK for rough operation
or seized U- joints. INSTALL
new U- joints as necessary.
REFER to Section 205 - 01 .
z Binding,
damaged or
galled splines
on the driveshaft
slip- yoke z
CLEAN and INSPECT the
splines of the slip- yoke,
driveshaft and coupling
shaft for a worn, damaged
or galled condition.
INSTALL a new slip- yoke or
driveshaft assembly as
necessary. REPAIR as
necessary. REFER to
Section 205 - 01 .
z Driveline vibration—
occurs at cruising
speeds z
U-joints are
worn. z
CHECK for wear or incorrect
seating. INSTALL new U-
joints as necessary. REFER
to Section 205 - 01 .
z Worn or
damaged
driveshaft center
bearing support. z
CHECK the insulator for
damage or wear. ROTATE
the driveshaft and CHECK
for rough operation.
INSTALL a new center
bearing support as
necessary. REFER to
Section 205 - 01 .
z Loose axle
pinion flange
bolts. z
INSPECT the axle pinion
flange. TIGHTEN the pinion
flange bolts to specification.
REFER to Section 205 - 01 .
z Excessive axle
pinion flange
runout. z
CARRY OUT a Runout
Check. REPAIR as
necessary. REFER to
Section 205 - 01 .
z Driveshaft is
out-of- balance. z
CHECK the driveshaft for
damage, missing balance
weights or undercoating.
CHECK driveshaft balance. Klj . 22 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

CARRY OUT a driveline
vibration test. REFER to
Section 205
- 00 . REPAIR as
necessary.
z Binding or
damaged
splines on the
driveshaft slip-
yoke. z
CLEAN and INSPECT the
splines of the slip- yoke,
driveshaft and coupling
shaft for wear or damage.
INSTALL a new slip- yoke or
driveshaft assembly as
necessary. REFER to
Section 205 - 01 . REPAIR as
necessary.
z Driveshaft
runout. z
CARRY OUT a Runout
Check. REFER to Section 205 - 00 . REPAIR as
necessary.
z Incorrect lateral
and radial
tire/wheel
runout. z
INSPECT the tire and
wheels. MEASURE tire
runouts. REPAIR or
INSTALL new components
as necessary. REFER to
Section 204 - 04 .
z Driveline angles
out of
specification. z
CHECK for correct driveline
angles. REPAIR as
necessary. REFER to
Section 205 - 00 .
z Incorrectly
seated CV joint
in the front
wheel hub. z
CHECK the outer CV joint
for correct seating into the
hub. REPAIR as necessary. Symptom Chart —
Engine Noise/Vibration Condition
Possible Sources Action
z Grinding noise—
occurs during
engine cranking z
Incorrect starter
motor mounting. z
INSPECT the starter motor
for correct mounting.
REPAIR as necessary.
REFER to Section 303 - 06 .
z Starter motor. zCHECK the starter motor.
REPAIR or INSTALL a new
starter motor as necessary.
REFER to Section 303 - 06 .
z Incorrect starter
motor drive
engagement. z
INSPECT the starter motor
drive and flexplate/flywheel
for wear or damage.
INSTALL a new starter
motor drive or flywheel as
necessary. REFER to
Section 303 - 06 .
z Engine ticking
noise z
Fuel injector.
z Fuel line.
z Oil pump.
z Valve lifter.
z Belt tensioner.
z Water pump.
z Obstruction of cooling
fan. z
Go To Pinpoint Test B .
z Engine drumming zPowertrain mount. zCARRY OUT Klj . 23 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...