tire pressure FORD MUSTANG 2003 Workshop Manual

DESCRIPTION AND OPERATION
Jacking
WARNING: Never run the engine with one wheel off the ground, such as when changing a
tire. The wheel still on the ground could cause the vehicle to move.
CAUTION: The jack (17080) provided with the vehicle is intended to be used in an
emergency for changing a deflated tire. To avoid damage to the vehicle, never use the jack to
lift the vehicle for any other purpose. Refer to the Owner Guide when using the jack supplied
with the vehicle.
CAUTION: Under no circumstances should the vehicle ever be lifted by the suspension
arm brackets, rear stabilizer or differential housing or convertible cross brace. Severe damage
to the vehicle could result.
CAUTION: Do not attempt to use jack pressure on either the front bumper (17757) or the
rear bumper (17906) of any vehicle. Damage to the bumper covers will occur.
Lift the vehicle using the Jacking Points procedure in this section.
Jacking Points
To lift the front or either side of the front end, position the floor jack under the front frame lift points. SECTION 100-
02: Jacking and Lifting 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4920/S3B~us~en~ ...

z
Change engine oil and install a new oil filter, lube front lower control arm and steering linkage
ball joints with zerk fittings (if equipped) every 4,800 km (3,000 miles) or 3 months.
z Inspect brake system and check battery electrolyte level (Patrol cars) every 8,000 km (5,000
miles).
z Install a new fuel filter every 24,000 km (15,000 miles).
z Change automatic transmission fluid, lubricate 4x2 wheel bearings, install new grease seals and
adjust bearings every 48,000 km (30,000 miles).
z Install new spark plugs and change transfer case fluid every 96,000 km (60,000 miles).
z Install a new cabin air filter as required.
When operating in dusty conditions such as unpaved or dusty roads:
zChange engine oil and install a new oil filter every 4,800 km (3,000 miles) or 3 months.
z Install a new fuel filter every 24,000 km (15,000 miles).
z Change automatic transmission fluid every 48,000 km (30,000 miles).
z Change transfer case fluid every 96,000 km (60,000 miles).
z Install a new engine air filter as required.
z Install a new cabin air filter as required.
When operating in off- road conditions:
z Change automatic transmission fluid every 48,000 km (30,000 miles).
z Change transfer case fluid every 96,000 km (60,000 miles).
z Install a new cabin air filter as required.
z Inspect and lubricate U- joints.
z Inspect and lubricate steering linkage ball joints with zerk fittings.
Checks and Services
Certain basic maintenance checks and inspections should be carried out at specified intervals. Any
recognized adverse condition should be corrected as soon as possible.
Maximum Oil Change Interval (Normal Schedule) z8,000 km (5,000 miles) or 6 months, whichever occurs first.
Maximum Oil Change Interval (Special Operating Conditions)
z4,800 km (3,000 miles) or 3 months.
Monthly Checks
Check each of the following items every month:
zAll interior and exterior lights.
z Tires for wear and correct air pressure. Klj . 2 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Engine oil fluid level.
z Windshield washer solvent fluid level.
z Check and drain fuel/water separator.
Six Month Checks
Check each of the following items at least every six months:
zLap/shoulder belts and seat latches for wear and function.
z Spare tire air pressure.
z Power steering fluid level.
z Parking brake for correct operation.
z Safety warning lamps (brake, ABS, air bag, safety belt) for correct operation.
z Coolant system fluid level and correct strength.
z Battery connections. Clean if necessary.
z Clutch fluid level, if equipped.
z Windshield washer spray, wiper operation, clean all wiper blades.
z Lubricate all hinges, latches and outside locks. Inspect for correct operation.
z Lubricate door rubber weatherstrips. Inspect for excessive wear.
z Clean body and door drain holes. Inspect for clogs and obstructions.
Special Checks (Mustang Only)
Carry out the following check every 8,000 km (5,000 miles):
zAdjust clutch by lifting pedal (manual transmission Mustang only, as described in owner guide).
Normal Schedule
The following checks or procedures should be carried out for all cars, minivans, light trucks, sport
utilities, vans, 4x4s, natural gas and propane vehicles.
8,000 Km (5,000 Miles) zChange engine oil and install a new oil filter.
z Rotate tires and inspect for wear.
16,000 Km (10,000 Miles)
zChange engine oil and install a new oil filter.
z Inspect tires for wear. Rotation recommended for optimal tire life.
24,000 Km (15,000 Miles)
zChange engine oil and install a new oil filter. Klj . 3 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Index Card
Place an index card or a piece of paper between the weatherstrip and the sealing surface, then close
the door. Slowly withdraw the index card or paper after the door is closed and check the amount of
pressure on the weatherstrip. There should be a medium amount of resistance as it is withdrawn.
Continue around the entire seal area. If there is little or no resistance, this indicates insufficient contact
to form a good seal. At these points, the door, the glass, or the weatherstrip is out of alignment. Klj . 14 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

information, REFER to
Section 205
- 00 .
REPAIR as necessary.
z Transmission
rumble/growl— noise at
all speeds in forward
gears, more
pronounced in a heavy
acceleration condition z
Damaged or worn
transmission
bearing or gears
(high mileage
vehicles). z
CHECK transmission
fluid for excessive
metal particles.
REPAIR as necessary.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Transfer case whine—
noise at all ranges z
Incorrect fluid level
or fluid quality. z
CHECK that the
transfer case is filled to
the correct level and
with the specified fluid.
REFER to Section 308 -
03A for T50D
transmissions or
Section 308 - 03B for
TR3650 transmissions.
z Worn oil pump. zDISASSEMBLE the
transfer case. CHECK
the oil pump for wear or
damage. REPAIR as
necessary.
z Under- inflated or
oversized tires. z
CONFIRM that the tires
and wheels are correct
for the vehicle. CHECK
that the tire inflation
pressures are correct.
z Transfer case
growl/rumble— noise at
all ranges (A small
amount of planetary
noise can be heard
when the transfer case
is operated in low
range.) z
Damaged or worn
bearings or
planetary gear. z
DISASSEMBLE the
transfer case. CHECK
the bearings or
planetary gear for wear
or damage. REPAIR as
necessary.
z Transfer case
scraping/grating—
noise at all ranges z
Excessively
stretched drive
chain hitting the
case. z
DISASSEMBLE the
transfer case. CHECK
the drive chain for wear
or damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at all
ranges or high range
only z
Worn or damaged
sun (input) gear,
clutch pack
(intermediate) gear
or output shaft gear. z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
howl/hum— noise at
low range only z
Worn or damaged
intermediate gear
and sliding gears
(clutch pack). z
DISASSEMBLE the
transfer case. CHECK
the gears for wear or
damage. REPAIR as
necessary.
z Transfer case
vibration— vibration felt
with vehicle in 4WD z
Transfer case
mounting.
z Driveshaft out of
balance.
z Excessive pinion z
Go To Pinpoint Test M . Klj . 44 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Suspension System
Inspection and Verification
1. Road test. zVerify the customer's concern by performing a road test on a smooth road.
2. Inspect tires. zCheck the tire pressure with all normal loads in the vehicle and the tires cold. For
additional information, refer to the vehicle certification (VC) label.
z Verify that all tires are sized to specification.
z Inspect the tires for incorrect wear and damage.
3. Inspect chassis and underbody. zRemove any excessive accumulation of mud, dirt or road deposits from the chassis and
underbody.
4. Inspect for aftermarket equipment. zCheck for aftermarket changes to the steering, suspension, wheel and tire components
(such as competition, heavy duty, etc.) The specifications shown in this manual do not
apply to vehicles equipped with aftermarket equipment.
5. Inspect shock absorbers. All vehicles are equipped with gas- pressurized hydraulic shock absorbers. These shock
absorbers are not adjustable or refillable and cannot be repaired.
zOil Leak: A light film of oil (weepage) on the upper portion of the shock absorber is
permissible and is a result or correct shock lubrication. Weepage is a condition in which a
film of oil accumulates on the thin tube (body) and is normally noticed due to the
collection of dust in this area. If shock absorbers exhibit this weepage condition, they are
functional units and new shock absorbers should not be installed. Leakage is a condition
in which the entire shock absorber body is covered with oil and the oil will drip from the
shock absorber onto the pavement. If condition exists:
„Make sure fluid observed is not from sources other than the shock absorber.
„ Install a new shock absorber, if necessary.
z Vehicle Sag: Many times new shock absorbers are installed in an effort to solve a vehicle
sag concern. Shock absorbers by design are hydraulic damping units only and, unlike
suspension springs, do not support any suspension loads. Therefore, installing a new
shock absorber will not correct a vehicle sag concern.
z Installment in Pairs: In the past it was recommended that new shock absorbers be
installed in pairs if one unit became unrepairable. New shock absorbers no longer need
to be installed in pairs when only one unit is not repairable.
SECTION 204-
00: Suspension System — General Information 2003 Mustang Workshop Manual Visual Inspection Chart
Mechanical Klj . 1 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. If an obvious cause for an observed or reported condition is found, correct the cause (if
possible) before proceeding to the next step.
7. If the fault is not visually evident, determine the symptom and GO to Symptom Chart .
Symptom Chart z
Front wheel bearing(s)
z Loose or damaged front or rear suspension components
z Loose, damaged or missing suspension fastener(s)
z Damaged spring(s)
z Damaged or leaking strut and spring assemblies
z Damaged or leaking shock absorber(s)
z Worn or damaged suspension bushing(s)
z Loose, worn or damaged steering system components
z Damaged axle components
Symptom Chart Condition
Possible Sources Action
z Dogtracking zExcessive rear
thrust angle. z
CHECK the wheel alignment.
ADJUST as necessary.
z Front or rear
suspension
components. z
INSPECT the front and rear
suspension system. REPAIR
or INSTALL new suspension
components as necessary.
REFER to Section 204 - 01 or
Section 204 - 02 .
z Drive axle
damaged. z
REPAIR as necessary. Refer
to the appropriate section in
Group 205 for the procedure..
z Drift/pull zUnequal tire
pressure. z
ADJUST tire pressure.
z Excessive side-to-
side difference in
caster or camber. z
CHECK the wheel alignment.
ADJUST as necessary.
z Tire forces. zROTATE tires front to rear.
z Unevenly loaded or
overloaded vehicle. z
NOTIFY the customer of
incorrect vehicle loading.
z Steering
components. z
REFER to Section 211 - 00 .
z Brake drag. zREFER to Section 206 - 00 .
z Front bottoming
or riding low z
Strut(s). zINSTALL new strut(s) as
necessary. REFER to Section 204 - 01 .
z Front coil springs
(5310). z
CHECK ride height. INSTALL
new springs as necessary.
REFER to Section 204 - 01 .
z Incorrect tire
wear z
Incorrect tire
pressure (rapid
center rib or inner
and outer edge
wear). z
ADJUST tire pressure. Klj . 2 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Safety Precautions
WARNING: Never run the engine with one wheel off the ground, for example, when
changing a tire. The wheel(s) resting on the ground could cause the vehicle to move.
WARNING: The tire and wheel must always be correctly matched. It is very important to
determine the size of each component before any assembly operations commence. Failure to
adhere to these instructions can result in an explosive separation and cause serious bodily
injury or death.
WARNING: Aftermarket aerosol tire sealants are extremely flammable. Always question
the customer to make sure these products have not been used.
WARNING: Aftermarket wheel assemblies may not be compatible with the vehicle. Use of
incompatible wheel assemblies can result in equipment failure and possible injury. Use only
approved wheel assemblies.
WARNING: Use only wheels and wheel nuts that have been designed for current model
year Ford trucks. Aftermarket wheels or wheel nuts may not fit or function correctly, and can
cause personal injury or damage the vehicle.
WARNING: Always wear safety goggles or a face shield when performing any work with
tire and wheel assemblies.
CAUTION: Do not clean aluminum wheels with steel wool, abrasive- type cleaners or
strong detergents. Use Custom Bright Metal Cleaner 8A-19522- A or equivalent meeting Ford
specifications ESR- M5B194-B.
CAUTION: Reduce the air pressure as much as possible by pushing the valve core
plunger in prior to removing the valve core. Avoid working in a position in which the face or
body is directly over a tire in which there is pressure.
When performing any inspection or repair procedures on wheels (1007/1015) and tires, follow the
preceding safety precautions. SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Wheels And Tires
WARNING: Do not mix different types of tires, such as radial, bias, or bias- belted, on the
same vehicle except in emergencies. Vehicle handling can be seriously affected and can result
in loss of control.
Factory-installed tires and wheels are designed to operate satisfactorily with loads up to and including
full- rated load capacity when inflated to recommended inflation pressures.
Tire and Wheel Runout
Excessive radial and lateral runout of a wheel and tire assembly can cause roughness, vibration,
wheel tramp, tire wear, and steering wheel tremor.
Before checking runout, and to avoid false readings caused by temporary flat spots in the tires, check
runout only after the vehicle has been driven far enough to warm the tires. For additional information,
refer to Section 100 - 04 .
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Wheels And Tires
Inspection and Verification
WARNING: A vehicle equipped with a Traction- Lok® differential will always have both
wheels driving. If, while the vehicle is being serviced, only one wheel is raised off the ground
and the rear axle is driven by the engine, the wheel on the ground could drive the vehicle off
the stand or jack. Be sure both rear wheels are off the ground.
WARNING: Never run the engine with one wheel off the ground, for example, when
changing a tire. The wheel(s) resting on the ground could cause the vehicle to move.
WARNING: Do not balance the wheels and tires while they are mounted on the vehicle.
Possible tire disintegration or differential failure could result, causing personal injury and
extensive component damage. Use off- vehicle wheel and tire balancer only.
Be sure to follow the warnings when carrying out inspection and verification.
Road Test
Verify the customer concern by carrying out a road test on a smooth road. If any vibrations are
apparent, refer to Section 100 - 04 .
To maximize tire performance, inspect for signs of incorrect inflation and uneven wear, which may
indicate a need for balancing, rotation, or front suspension alignment.
Correct tire pressure and driving techniques have an important influence on tire life. Heavy cornering,
excessively rapid acceleration and unnecessary sharp braking increases tire wear.
Replacement tires must follow the recommended:
ztire sizes.
z speed rating.
z load range.
z tire construction type.
Use of any other tire size or type can seriously affect:
zride.
z handling.
z speedometer/odometer calibration.
z vehicle ground clearance.
z tire clearance between the body and chassis.
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...