seat adjustment GEELY CK 2008 Workshop Manual

Section 3 Removal & Installation................................................................................... 262Chapter 8 MK-20 ABS System........................................................................ 2 7 2Section 1 ABS Diagnosis ................................................................................................. 272
Section 2 ABS System Check .......................................................................................... 276
Section 3 Removal and Installation................................................................................. 292Part IV Air Conditioner and Inside & Outside Trim ......................297Chapter 1 A/C System...................................................................................... 2 9 7Section 1 The Structure & Working Principle of Refrigeration System...............................297
Section 2 Heating System ................................................................................................ 299
Section 3 A/C controlling system.................................................................................... 302
Section 4 Service Caution & Notice................................................................................ 304
Section 5 The Refrigeration System Operation Procedure..............................................305
Section 6 Basic System .................................................................................................... 308
Section 7 A/C System Faults Check & Troubleshooting................................................ 313Chapter 2 Inside & outside Trim and Accessory................................................318Section 1 Configuration Index............................................................................................318(I) Outside Trim And Front Accessory.................................................................................318
(II) Outside Trim and Rear Accessory.................................................................................319
(III) Front inside trim..........................................................................................................320
(IV) Rear inside trim ............................................................................................................321Section 2 Inside & Outside Trim and Accessories Removal and Installation.......................322(I) Front Bumper..................................................................................................................322
(II) Engine Hood.................................................................................................................324
(III) Outside Rear View Mirror
(IV) Rear trunk Lid...............................................................................................................327
(V) Rear Bumper...................................................................................................................329
(VI) Seat Removal, Installation and Adjustment...................................................................331
(VII) Seat Belt.....................................................................................................................335
(VIII) Instrument panel and auxiliary console.....................................................................338
(IX) A pillar inside trim and front door sill ............................................................................343
(X) B pillar inside trim........................................................................................................344
(XI) Cpillar inside trim and rear door sill.............................................................................345
(XII) Roof inside trim
(XIII) Carpet and Heat Insulator.............................................................................................347 ...............................................................................................326
...........................................................................................................346

213IV. HEADLAMP BEAM ADJUSTMENTLOW BEAM
1. Adjust the condition of the vehicle.
yMake sure the body around the headlamp is not deformed
yTire inflation pressure is the specified value
yPark the no-load vehicle on a level spot
ySit on the driver's seat and be ready for driving (with a full fuel tank)
yPut the vehicle in front of a wall, and let it be perpendicular to the wall
yEnsure the distance from the headlamps to the wall is 10 m
2. Inspect the headlamp beam
ySet up a screen as shown in the illustration, to adjust the headlamp aim
yCover the other lamps while a certain headlamp is adjusted.
yStart the engine
yTurn the headlamp low beam ON
yThen turn the adjusting screws controlling the beams. Make the main beam (the brightest point) at
the specified height, that is, the corner point of the "cut-off" line is located in the center of the
shaded part, as shown in the illustration.Low Beam LayDim and Bright
Cut Line AngleDistance from the central point of
the headlamp beam to the groundLow
BeamPosition of the Vehicle

3281.Rear trunk Lid Removal/Installation
Warning
It is dangerous to remove the rear trunk lid spring before supporting the rear trunk lid. The rear
trunk lid may drop and result in body injury. Fully open the rear trunk lid, support the rear trunk
lid before removing the brace.
Remove rear trunk lid under the help of the assistant.(1) Disconnect the negative (--) terminal cable from the battery;
(2) Disconnect rear trunk wire harness connector. Pull the rear trunk lid wire harness out from the rear
trunk;
(3) Remove rear trunk door lock cylinder assembly. Pull out the rear trunk door lock cable;
(4) Remove rear trunk lid spring;
(5) Remove rear trunk lid hinge connecting bolt. Remove the rear trunk lid;
(6) Remove rear trunk lid hinge seat mounting nut. Remove the rear trunk lid hinge seat and the rear trunk lid
hinge
(7) Remove rear trunk door oil filler cable assembly;
(8) Remove cushion;
(9) Remove rear trunk lid hinge pin. Remove rear trunk lid hinge from the bracket;
(10) Remove rear trunk lid weatherstrip;
(11) Remove rear trunk lid inside trim board clip, Remove rear trunk lid inside trim board;
(12) Remove rear license plate assembly mounting nut , Remove rear license plate assembly;
(13) The installation is in the reverse order of the removal.;
(14) Adjust the rear trunk lid. (See rear trunk lid adjustment)2.Rear trunk Lid Adjustment(1) Measure the clearance and height between the rear trunk lid and vehicle body.
(2) Loose the rear trunk lid hinge mounting bolt or the rear trunk latch mounting screw and reinstall the rear
trunk lid if it is not as specified.
Clearance
a: 3.74mm
b: 1.0mm
c: 4.0mm
(3) Tighten the rear trunk lid hinge bolt;
(4) Close the rear trunk lid

331(VI) Seat Removal, Installation and AdjustmentFront SeatSee Figure
Disassembly of Front Seat
1.Headrest Assembly 2. Headrest Support3.Snap Ring4.Front Seat Backassembly
5.Front Seat Back Cover 6.Cap Nut7.Front Seat Coupling Plastic Gasket
8.Track Assembly 9.Front Seat Cushion Cover 10.Front Seat Cushion Assembly
11.Adjuster Assembly12.Adjuster Hinge Cover1. Removal1Remove 4 bolts and the seat from the vehicle;
2Turn the headrest lock handle to"Non-LOCK". Remove headrest and bracket;
3Remove the attaching screw, Remove adjuster hinge cover from the front seat;
4Remove the 4 snap ring under the rear side of the seat back. Remove the set bolt and nut at the both sideof the seat back;
5Remove seat coupling plastic gasket;
6Remove the seat cushion, track assembly and adjuster assembly;
7Press the headrest support and push it upwards by hand in the direction as the Figure shows and removethe headrest support;
8Open the seat backcover. Remove the inner coversnap ring. Remove the seat backcover;