torque GEELY FC 2008 Owners Manual

Power steering--Power steering gear assembly
34. Assemble steering middle shaft.
(a) Align the mark of steering middle shaft and steering small
gear shaft.
(b) Assemble the bolt.
Torque: 35 N
x xx x
xm
35. Assemble exterior dustproof cover of steering
column.
36. Assemble auxiliary bracket assembly (64000087).
(a) Use special tool to align the right side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt
temporarily.
(b) Use special tool to align the left side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt
temporarily.
(c) Use special tool to align the left side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt.
Torque:
A bolt: 157 ± 10 N
x xx x
xm
B bolt: 113 ± 10 N
x xx x
xm
(d) Use special tool to align the right side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt.
Torque:
A bolt: 157 ± 10 N
x xx x
xm
B bolt: 113 ± 10 N
x xx x
xm
(e) After connecting with engine with one bolt and three screw
caps, hang it to auxiliary bracket.
Torque: 52 N.m ± 5 N
x xx x
xm
(f) Assemble carling to body with two bolts.
Torque: 39 ± 3 N
x xx x
xm
(g) Assemble the front suspension of engine to carling with
two screw caps.
Torque: 52 ± 5 N
x xx x
xm
Align the mark
Special
tool
Special tool
 210 

Power steering--Power steering gear assembly
37. Connect the bolts and nuts of left/right control arm
and control arm ball head.
Torque: 142 ± 10 Nx xx x
xm
Hint: connect the other side with same method.
Connect left lower control arm to steering knuckle with
bolt and two nuts.
38. Connect linking lever assembly of left/right front
stabilizer bar [64000097].
Use socket head wrench (5mm) to fix bolt, then connect sta-
bilizer linking lever with screw cap.
Torque: 74 ± 5 N
x xx x
xm
Hint: connect the other side with same method.
39. Connect the in-out oil pipe assembly of power steer-
ing gear [64000131].
(a) Connect the in-out oil pipe fixed clamp of power steering
gear with bolt.
Torque: 7.8 N
x xx x
xm
(b) Use special tool to connect the in-out oil pipe assembly of
power steering gear.
Torque: 41 N
x xx x
xm
Hint:
zUse the torque wrench whose lever length is
345mm.
zSpecial tool should be parallel with torque wrench,
only this could make practical torque value.
Hint: connect the other side with same method.
40. Connect the ball head at the left side of transversal
lever.
(a) Connect the ball head at the left side of transversal lever
with screw cap.
Torque: 49 ± 5 N
x xx x
xm
(b) Assemble new cotter pin.
Note: if cotter pin hole could not be aligned , tighten
the screw cap for 60 again.
Hint: connect the other side with same method.
 211 
Length of lever

Power steering--Power steering gear assembly
41. Connect the ball head at the right side of transver
sal lever .
42. Assemble right bottom defending board of engine
[68000004].
43. Assemble left bottom defending board of engine
[68000003].
44. Assemble front wheel
Torque: 103 ± 10 Nx xx x
xm
45. Connect steering slide shaft assembly.
(a) Align the mark between steering middle shaft and sliding
shaft.
(b) Assemble B bolt.
Torque: 35 ± 3 N
x xx x
xm
(c) Tighten the A bolt.
Torque: 35 ± 3 Nx xx x
xm
46. Assemble inner dustproof cover of steering column [64000123].
Assemble inner dustproof cover of steering column with two screw caps.
47. Make front wheel face the front
Hint: lift up front wheel shaft.
48. Assemble helix cable assembly (equipping with SRS).
49. Assemble steering wheel assembly [67010001].
(a) Align the mark between steering wheel and main shaft of steering column.
(b) Lock the fixed screw cap of steering wheel temporarily.
50. Add power steering oil (referring to page 200).
51. Exhaust the air in power steering system (referring to page 200).
52. Check the central point of steering wheel.
(a) Check the central point of steering wheel.
(b) Lock the fixed screw cap of steering wheel.
Torque: 50 ± N
x xx x
xm
53. Assemble safety airbag assembly at the side of driver (equipping with SRS) [67010011].
54. Check whether there is oil leakage.
55. Check the engine cover assembly.
56. Adjust the engine cover assembly.
57. Check and adjust the front wheel alignment (referring to page 87).
 212 

Air conditioner--Refrigerant pipeline
Refrigerant pipeline
Parts
.
 ::
:::
Regulated torque
 222 
¹Ü¹Ü
¹Ü¹Ü¹Ü··
···ÂÝÂÝ
ÂÝÂÝÂÝĸĸ
ĸĸĸ
Refrigerant low
pressure hose
Pipeline nut
Refrigerant high
pressure hose
Refrigerant liquid pipe

Air conditioner--Air conditioner central heating core assembly
53. Assemble expansion valve.
(a) Spread Refrigerant oil on two O-shape loops and assemble
it on expansion valve.
Refrigerant oil: ND-OIL No. 8 or other products with
same grade.
(b) Assemble expansion valve on evaporator.
54. Assemble air conditioner pipeline.
(a) Spread Refrigerant oil on two O-shape loops and assemble
it on air conditioner pipeline.
Refrigerant oil: ND-OIL No. 8 or other products with
same grade.
(b) Use planetary wrench (5.0mm) to assemble air conditioner
pipeline with two planetary bolts.
Torque: 3.5 N
x xx x
xm
(c) Assemble two screws and extending cover.
55. Assemble panel framework body assembly
Assemble panel strengthening beam and five bolts.
56. Assemble lower assemble bracket of panel
framework.
Assemble lower assemble bracket of panel framework, screw
cap and bolt.
 232 

Air conditioner--Compressor assembly
zIf Refrigerant oil quantity in the disassembled old com-
pressor is too little, check whether the system leaks Re-
frigerant oil.
zOnly could use 100PG Refrigerant oil.
9. Assemble compressor and electromagnetic clutch.
(a) Assemble compressor, electromagnetic clutch and three
bolts.
Torque: 24.5 N
⋅ ⋅⋅ ⋅
⋅m
(b) Connect the joint.
10. Assemble driving belt.
11. Assemble refrigerant No.1 high pressure hose.
(a) Disassemble the cover on pipeline joint.
(b) Spread Refrigerant oil on new O-shape loop and assemble
it on No.1 refrigerant high pressure hose.
Refrigerant oil: 100PG
(c) Connect No.1 refrigerant high pressure hose to compres-
sor and electromagnetic clutch and assemble the bolts.
Torque: 9.8 N
⋅ ⋅⋅ ⋅
⋅m
12. Assemble refrigerant No.1 low pressure hose.
(a) Disassemble the cover on pipeline joint.
(b) Spread Refrigerant oil on new O-shape loop and assemble
it on No.1 refrigerant low pressure hose.
Torque: 23 N
⋅ ⋅⋅ ⋅
⋅m
(c) Connect No.1 refrigerant low pressure hose to compres-
sor and electromagnetic clutch and assemble the bolts.
Torque: 9.8 N
⋅ ⋅⋅ ⋅
⋅m
13. Fill the refrigerant (referring to page 221).
Regulated quantity: 660 ± 10g
14. Heat the engine.
15. Check whether the refrigerant leaks.
 235 

Air conditioner--Condenser AssemblyCondenser AssemblyInspection on the automobile1. Check the Condenser Assembly.(a) If the radiating fins of condenser assembly are dirty, wipe it with water and blow it to dry with com-
pressed air.
Notice: Do not damage the radiating fin.
(b) If the radiating fin is curved, repair it with gad screw driver or pliers.2. Check whether the Condenser leaks.(a) Use leakage detector to check whether the Refrigerant leaks at the joint of the pipelines.
(b) If it leaks, check the fastening torque of joint part.Overhaul1. Disassemble the radiator cover assembly.
2. Recycle the HFC-134a(R134a)
3. Disassemble the Refrigerant liquid pipe A.(a) Disassemble the bolt from the condenser assembly and
disconnect the Refrigerant liquid pipe A.
(b) Disassemble the O-shape ring from the Refrigerant liquid
pipe.
Notice: The pipeline should be covered immediately
to prevent damp or dust from getting into the system.4. Disassemble the Refrigerant NO.1 high pressure
hose.(a) Disassemble the bolt and the Refrigerant NO.1 high pres-
sure hose from the condenser assembly.
(b) Disassemble the O-shape ring from the Refrigerant high
pressure hose.
Notice: The pipeline should be covered immediately
to prevent damp or dust from getting into the system.5. Disassemble the condenser assembly.(a) Disassemble those two bolts and the bracket on water tank. 236 

Air conditioner--Condenser Assembly(b) Disassemble two bolts.
(c) Pull the component on the top of water tank assembly back
to disassemble the condenser assembly.6. Disassemble the drier(a) Use 10mm hexagon wrench to disassemble the cover and
filter core from regulator.
(b) Disassemble two O-shape rings from the cover.
(c) Use the acutilingual pliers to disassemble the drier.7. Assemble the drier.(a) Use the acutilingual pliers to assemble the drier.
(b) Put the O-shape ring in the cover.
(c) Spread freezing lubricant at the connecting part between
the O-shape ring and the cover.
Refrigerant oil: 100PG
(d)Use the 10mm hexagon wrench key to assemble the cover
to condenser assembly.
Torque: 12.3 N⋅ ⋅⋅ ⋅
⋅m8. Assemble condenser assembly.
9. Assemble Refrigerant NO.1 high pressure hose.(a) Disassemble the cover from the tie –in of the pipe.
(b) Daub enough Refrigerant oil to lubricate at the connecting
part between the O-shape ring and the cover.
Refrigerant oil: 100PG
(c) Use the bolt to connect Refrigerant high pressure hose
with condenser assembly.
Torque: 5.1 N⋅ ⋅⋅ ⋅
⋅mInner hexagon
socket wrench
Adjuster 237 

Air conditioner--Condenser Assembly10. Assemble the Refrigerant liquid pipe A.(a) Disassemble the cover from the pipeline joint.
(b) Assemble the O-shape ring to the Refrigerant liquid pipe
A.
(c) Spread enough Refrigerant oil to lubricate at the conencting
part between the O-shape ring and the cover.
Refrigerant oil: 100PG
(d) Use the bolt to connect the Refrigerant liquid pipe A with
condenser assembly.
Torque: 5.4 N⋅ ⋅⋅ ⋅
⋅m11. Fill with Refrigerant.Regulated quantity: 660 ± ±± ±
± 10g12. Warm the engine.
13. Check whether the Refrigerant leaks. 238 

Safety belt--Front safety belt
Subassembly
(e) Treatment for safety belt pre-tension crimper.
(1) Disassemble the tyre and special tool.
(2) Put safety belt pre-tension crimper in plastic bag, then
bind the bag for treatment with other parts.
N.
m : Regulated torque
Trim board of pedal of
front doorFront safety belt
locker assembly Trim cover of safety belt
lower fixed bolt Trim board of pedal
of rear door Front safety belt
crimper assembly Lower inner defending
board of middle columnTrim cover of safety belt
upper fixed bolt41
Q184C1020
41
Q184C1020
41
Q184C1020
41
Q184C1020
 273