GEELY FC 2008 Workshop Manual

Wiper and cleaner--Wiper and cleaner systemInspect1. Inspect the conduction of right combination
switch [67000079](a) Inspect the conduction of every terminal of joints.
Right combination switchSwitch position terminals connect with avometerregular situations
OFF - Not conduction
ON WIG-WSconductionSwitch positionsterminals connect with avometerregular situations
MISTSWL-WIGConduction
OFF AS-SWLConduction
INT AS-SWL/SWL-WIGConduction
LO SWL-WIGConduction
HI SWH-WIGConduction(c) Inspect the function of cleaner
(1) Turn right assembled switch to OFF.
(2) Connect battery positive wire with joint terminal WIG, connect negative to terminal EW.
(3) Connect voltmeter positive wire with joint terminal WS, connect negative to terminal EW.
(4) Switch on cleaner switch and inspect its going. (b) Inspect intermittent function of wiper.
(1) Connect voltmeter positive wire with joint terminal SWL, connect negative to terminal EW.
(2) Connect battery positive wire with joint terminal WIG, connect negative to terminal EW.
(3) Turn right assembled switch to INT.
(4) Connect battery positive wire with terminal AS for 5 seconds.
(5) Connect battery negative with terminal AS for 5 seconds actuate intermittent relay and check the
voltage between terminal SWL and terminal EW . Sprinkler switch 300 

2. Inspect the function of generator
(a) low speed:
Connect battery positive wire with joint terminal SWL, connect negative to terminal ES. Inspect whether
generator work at low speed.
If its function does not in conformity with regulations, replace wiper.
(b) high speed
Connect battery positive wire with joint terminal SWH, connect negative to terminal WS. Inspect
whether generator work at high speed.
If its function does not in conformity with regulations, replace wiper.
(c) Free stop position
(1) Connect battery positive wire with joint terminal SWL, connect negative to terminals ES to make
generator work at low speed. Disassemble terminal SWL
lead to make generator stop except stop position.
(2) Connect terminal SWL with terminal AS
(3) Connect battery positive wire with joint terminal SWL to
make generator work at low speed again. Inspect gen-
erator whether stop at the stop position.
If its function does not in conformity with regulations,
replace wiper.
Wiper and cleaner--Wiper and cleaner system
Free stop
position
 301 

Wiper and cleaner--Right combination switch
Right combination switch
Change
1. Disassemble the lower trim board of the steering
gear
2. Disassemble right combination switch assembly
[67000079]
(a) Disassemble the joints.
(b) Press fixed jaw to separate meshing then disassemble right
combination switch assembly.
Notes: Do not overly press fixed jaw, or it may de
damaged.
 302 
Fixing
claw

Wiper and cleaner--Wiper generator
Fixing clasp
Fixing
claw
Wiper generator
Change
1. Disassemble wiper arm cap.
2. Disassemble auxiliary wiper arm assembly
[68000059]
Disassemble screw cap and auxiliary wiper arm assembly.
3. Disassemble main wiper arm assembly [68000057]
Disassemble screw cap and main wiper arm assembly.
4. Disassemble generator cap to fire barrier seal.
Separate eight fixed buckles to disassemble the seal from gen-
erator cap to fire barrier.
5. Disassemble ventilation cover on passenger side.
Disassemble five fixed jaws so as to disassemble ventilation
cover on passenger side.
6. Disassemble ventilation cover on driver side.
Disassemble five fixed jaw so as to disassemble ventilation
cover on driver side.
7. Disassemble wiper connecting rod assembly
[68000053]
(a) Disassemble the joint.
(b) Disassemble the bolt.
(c) Slide wiper connecting rod assembly to passenger side to
separate meshing of rubber pin so as to disassemble wiper
connecting nod.
Fixing
claw
 303 
Pin

Wiper and cleaner--Wiper generator
8. Disassemble wiper generator
(a) Separate two connecting rod caps of shaft pins.
(b) Separate two star- bolts so as to disassemble wiper
generator.
9. Assemble wiper generator
(a) Daub MP grease to connecting rod caps of wiper generator.
(b) Use two Star-bolts to assemble wiper generator to wiper
connecting rod.
Torque: 5.39 N.m
10. Assemble wiper connecting rod assembly
[68000053]
(a) Meshing wiper connecting rod rubber pin
(b) Use two bolts to assemble wiper connecting rod.
Torque:5.5 N.m
(c) Connect the joints.
11. Assemble assistant wiper arm assembly [68000059]
(a) Use steel brush to clean small tooth slot of wiper pivot.
(b) Use bolt cap to fix wiper arm on passenger side to make
wiper blade at the position as drawing.
Torque: 20.5 N.m
12. Assemble main wiper arm assembly [68000057]
(a) Use steel brush to clean small tooth slot of wiper pivot.
(b) Use bolt cap to fix wiper arm on driver side to make wiper
vane at the position as drawing.
Assembly starting and
stopping position
 304 
Assembly starting and
stopping position

Wiper
Change
1. Disassemble left wiper shelf.
Disassemble left wiper shelf from left wiper arm.
Note: Do not bend wiper arm adown when disassemble
wiper shelf.
2. Disassemble wiper blade
Disassemble wiper blade from wiper shelf.
3. Disassemble wiper blade fixed branch vane.
4. Assemble wiper blade fixed branch vane.
Note: Be careful, do not assemble front and rear branch
blade by mistake.
5. Assemble wiper blade
Put the head of wiper blade(on big end side) on the direction of
wiper arm connecting shaft side, when you assemble left wiper
blade.
Note: Pull the wiper blade into wiper shelf completely.
Wiper and cleaner--Wiper
 305 

Wiper and cleaner--Cleaner nozzle
Cleaner nozzle
Adjustments
1. Inspect cleaner nozzle
When engine works, inspect whether wiper water blast spurt in the area of wind shield bias as the drawing.
 306 
Adhesives strip

Audio system
Audio system
Notes
1. Observe notes for disposal and operation
(a) Please explain to customers: when take battery’s negative terminal off, the memory broadcasting
station on the audio AM/FM set on the radio will be deleted. So, before taking battery
s negative
terminal off ,note the station’s information according to your need. After taking back negative terminal,
set former station again.
(b) Before disassemble/assemble the radio, inspect and take cassette and CD out in.
Clues on: the malfunction of disassemble/assemble the radio is because the tape or CD can
not take out. Do not take it out by force. Drive the car to the service station.
(c) Do not touch the audio film of loudhailer
2. Refer to instructions about using and maintaining audio system
Audio system--Audio system
 307 

Audio system--Radio assembly
Radio assembly
Change
1. Disassemble the CD machine assembly (referring to page 342)
2. Disassemble radio assembly
(a) Disassemble four bolts as the drawing.
(b) Take the joint apart, then disassemble radio assembly.
 308 

Left front door loudhailer
Change
1. Disassemble left front door control panel assembly
[68000142]
2. Disassemble left front door inner guard board as-
sembly [68010049]
3. Disassemble left front door water screen assembly
[68000140]
4. Disassemble left front door loudhailer assembly
[67000127]
(a) Disassemble three rivets.
(b) Disassemble the joint, then disassemble left front loudhailer.
5. Diasassemble left front door loudhailer assembly
[67000127]
(a) Use three new rivets to assemble new left front door
loudhailer assembly.
(b) Connect the joint.
6.Replace right front door loudhailer,just as upper
method
Audio system--Left front door loudhailer
 309