fuse box GEELY FC 2008 Workshop Manual

Diagnostic procedure
(1) Check the battery
zIs the voltage higher than 9V?
Yes: make next operation,
No: The voltage of battery is too low, check the charging/discharging system.
zRefer to chapter 1, Inspection of battery, charging system
(2) Check the wiring harness between battery and safety boox.
zDisassemble fuse panel to set ignition switch at ON position without loosening connector.
zMeasure whether the voltage of related two pins of fuse panel is more than 9V?
Yes: make next step
No: check and repair the wiring harness.
(3) Check the wiring harness between fuse panel and the connector of safety airbag system unit.
Warning:
If the treatment is wrong, safety airbag assembly might be triggered to unfold to make heavy
human hurt, so, before the treatment, it is necessary to read repairing warnings carefully.
Refer to repairing warning of safety airbag system.
a. Set ignition switch at LOCK position,
b. Loosen the cathode cable of battery and keep this state for one minute at least,
c. Disassemble the shell body of steering column,
d. Loosen the connector of helix cable,
e. Disassemble glove box (with safety airbag assembly at the side of passenger),
f. Loosen the connector of safety airbag assembly at the side of passenger,
g. Disassemble left inner trim board,
h. Loosen the connectors of all safety airbag system units,
i. Assemble cathode cable of battery, and set the ignition switch at ON position, then measure
whether the voltage of safety airbag system unit and grounding connector pin is more than 9V?
Yes: make next step,
No: change the wiring harness.
j. Set the ignition switch at LOCK position,
Loosen the cathode cable of battery and keep this for one minute at least.
k . Disassemble left inner trim board,
l. Cut off the conversion connector of safety airbag system unit,
m. Assemble cathode cable of battery, and set the ignition switch at ON position, then measure
whether the voltage of safety airbag system unit and grounding connector pin is more than 9V?
Yes: malfunction diagnosis ends,
No: change the wiring harness.
Supplemental restraint system--Remove malfunction
 254 

Malfunction
Wiper and cleaner do not work.
Wiper does not work on LO, HI or MIST.
Wiper does not work on INT
Washer generator does not work
When cleaner switch ON, wiper does not
work.
Wiper cleaner can not spout
zRight assembled switch on HI, wiper
blade will touch the bodywork.
zWhen right combination switches are OFF, washer will
not return to original position or stop position is incorrect.
Component names
1. ignition switch
2. ignition relay
3. (wiper) fuse (central power distribution box)
4. right assembled switch
5. wiring harness
1. right assembled switch
2. wiper generator
3. wiring harness
1. right assembled switch
2. wiper generator
3. wiring harness
1. (washer) fuse (central power distribution box)
2. wiper switch
3. wiper generator
4. wiring harness
1. right assembled switch
2. washer generator
3. wiring harness
1. cleaner hose and nozzle
1. right assembled switch *1
2. wiring harnessReference pages
-
-
-
302
302
303
302
303
-
-
-
-
302
303
-
-
302
-
Inspect the car
Inspect the function of cleaner generator
(1) Add some rinsing to wiper water tank, then disassemble
cleaner generator joint.
(2) Connect battery wire with cleaner generator joint terminal2,
negative wire with terminal1,then inspect whether cleaner
generator works.
Notes: Be quick(in 20 seconds) to do this test to pre-
vent cleaner generator coil from burning.
If its function does not in accord with regulations, replace
cleaner generator.
Wiper and cleaner--Wiper and cleaner system
Wiper and cleaner
Wiper and cleaner system
Malfunction phenomena table
The underside table can help you to eliminating malfunction in wiring. It sorts as possibilities of malfunction’s
reasons.
*1:inspect set position of wiper arm and wiper blade.
 299 

Circuitry--Power supply
Circuitry
Power supply
Components (For reference only)
Center power
distribution
Engine room main
fuse box engine room assistant
fuse box
 313 

Switch position
UP
OFF
DOWNright front, avometer
terminal
4-15, 6-10
4-10, 6-10
6-15,4-10right rear, avometer
terminal
9-15, 7-10
9-10, 7-10
7-15, 9-10Left rear, avometer
terminal
3-15, 1-10
3-10, 1-10
1-15, 3-15situations
Conduction
Conduction
Conduction
Switch position
UP
OFF
DOWNright front, avometer
terminal
4-15
4-6
6-15right rear, avometer
terminal
9-15
7-9
7-15Left rear, avometer
terminal
3-15
1-3
1-15situations
Conduction
Conduction
Conduction
Windshield/bodywork glass/wing mirror--Electric window control system
Phenomena
Electric window does not Work(all)(electric
door lock does Not work)
Electric window does not work(all) (electric
door lock is normal)
Automation system does Not work
Only one window can not Move
Electric window system Does not workimpossible positions
1. POWER fuse(center power distribution box)
2.
window shift main relay (center Distribution box)
3. wiring harness
1. ignition switch
2. left front door control Panel assembly
3. wiring harness
4. electric window generator
1. left front door control panel assembly
2. electric window generator (driver seat)
1. left front control panel assembly
2. electric window switch
3. electric window generator
4. wiring harness
1. left front door control panel assembly
2. wiring harnesswiring harness
-
-
-
-
319
-
320
319
320
319
320
320
-
319
-.
Inspect
1. Inspect left front door control panel assembly
[68000142]
Action switch, inspect the conduction among joint terminals.
Notes: Whether it works good or bad ,it can judged by
basic function. Becauce the conduction can not inspect
by ascending or descending driver’s electric window main
switch.
Electric window does not locked
Electric window locked
Malfunction phenomena table
If the conduction does not limit to regulations, replace electric window main switch.
 319 

Anti-stealing and door lock--Electric door lock control system
3. Check panel junction box assembly.
(a) Check 25A DOOR fuse.
(b) Check conformity relay.
(1) Disassemble F, G, H and I joint on instrument junction
box.
(2) Check the voltage and conduction of every terminal of
joint. (d) Check security function:
(1) When closing all doors, open the driver window to operate door control switch out of automobile.
(2) Take down the key, open driver door, then close the door and lock (not use key). In this situation
above, check that door could not open locker even if door control switch (handle operation) is
pressed to locker opening side out of automobile.
(3) Take down the key, close and use the key to lock driver door. In this situation above, check that
door could not open locker even if door control switch (handle operation) is pressed to locker
opening side out of automobile.
(4) Take down the key, close and use remote control key to lock driver door. In this situation above,
check that door could not open locker even if door control switch (handle operation) is pressed to
locker closing side out of automobile (only applicable for the automobile equipping with remote
control door locker control system).
Hint:
zIn following situation, check whether security has been canceled.
zIgnition switch is turned to ON.
zUse key operation to open the driver door locker.
zAfter door locker is pressed to opening side by hand, door control switch (handle
operation) is pressed to locker opening side.
zUse remote control locker control to open the door (only applicable for the automobile
equipping with remote control door locker control system).
2. Electric window main switch assembly
Operate door control switch by hand to check its conduction.
 356 
Position of switch Terminal connected by avometerRegulated situation
LOCK 5-1 or 5-3Conduction
UNLOCK8-1 or 8-3↑