sensor GENESIS G90 2023 Owner's Guide

5-118
Convenience Features
ORS051284
)URQW:LQGVKLHOG:LSHUV
Operates as follows when the Engine
Start/Stop button is in the ON position.
MIST: For a single wiping cycle,
push the lever upward and
release. The wipers will operate
continuously if the lever is held in
this position.
OFF: Wiper is not in operation.
AUTO: The rain sensor located on the
upper end of the windshield
glass senses the amount of
rainfall and controls the wiping
cycle for the proper interval.
The more it rains, the faster the
wiper operates. When the rain
stops, the wiper stops. To vary
the speed setting, turn the speed
control knob.
LO: The wiper runs at a lower speed.
HI: The wiper runs at a higher speed.
Information
If there is heavy accumulation of snow
or ice on the windshield, defrost the
windshield for about 10 minutes, or until
the snow and/or ice is removed before
using the windshield wipers to ensure
proper operation.
If you do not remove the snow and/or ice
before using the wiper and washer, it may
damage the wiper and washer system.
AUTO (Automatic) control
ORS051085
The rain sensor located on the upper
end of the windshield glass senses
the amount of rainfall and controls the
wiping cycle for the proper interval.
The wiper operation time will be
automatically controlled depends on
rainfall.
When the rain stops, the wiper stops.
To vary the sensitivity setting, turn the
sensitivity control knob.
If the wiper switch is set in AUTO mode
when the Engine Start/Stop button is in
the ON position, the wiper will operate
once to perform a self-check of the
system. Set the wiper to the OFF position
when the wiper is not in use.
WIPERS AND WASHERS

5-119
05
WARNING
To avoid personal injury from the
windshield wipers, when the engine
is running and the windshield wiper
switch is placed in the AUTO mode:

[Do not touch the upper end of the
windshield glass facing the rain
sensor.

[Do not wipe the upper end of the
windshield glass with a damp or wet
cloth.

[Do not put pressure on the
windshield glass.
NOTICE

[When washing the vehicle, set the
ZLSHUVZLWFKLQWKH2))SRVLWLRQWR
stop the auto wiper operation. The
wiper may operate and be damaged
if the switch is set in the AUTO mode
while washing the vehicle.

[Do not remove the sensor cover
located on the upper end of the
passenger side windshield glass.
Damage to system components
could occur and may not be covered
by your vehicle warranty.

[Because of using a photo sensor,
temporary malfunction could occur
according to sudden ambient light
change made by stone and dust
while driving.
Windshield Washers
ORG3EV051079
In the OFF position, pull the lever gently
toward you to spray washer fluid on the
windshield.
The washer fluid is sprayed as the wipers
rise while operating. The spray and wiper
operation will continue until you release
the lever.
If the lever is released, the wipers
operate approximately 4 times and the
lever returns to it's original position

5-126
Convenience Features
Information
ORS051085
Never place anything near the ambient
light/solar sensor to ensure better control
of the heating and cooling system.
Manual Temperature Control
Mode
The heating and cooling system can be
controlled manually by pushing buttons
other than the AUTO button. In this case,
the system works sequentially according
to the order of buttons selected.
When pressing any button except the
AUTO button while using automatic
operation, the functions not selected will
be controlled automatically.
1. Start the vehicle.
2. Set the mode to the desired position.
To improve the effectiveness of
heating and cooling, select the mode
according to the following:

[Heating:

[Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to Fresh or
Recirculation mode.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn the
air conditioning system on.
7. Press the AUTO button to convert to
full automatic control of the system.
The climate control system settings
will be maintained, even when the
vehicle is turned OFF. However, the
climate control system settings will be
initialized when the battery has been
discharged, or when the cables have
been disconnected.
In this case, adjust the climate control
system settings again.

5-150
Convenience Features
UV-C sterilizer system
ORS051092
ORS051229
M: UV-C sterilizer system button,
N: UV-C LED,
O: UV-C Indicator light (upper part of armrest
touchscreen)
The rear seat console is equipped with
an antibacterial sterilization system for
personal belongings.
WARNING

[Press the button to turn UV-C
function off when it is not in use.
Being exposed to ultraviolet rays
from UV-C LED may be harmful to
your skin and eyes.

[Do not place magnetic items
(magnets, etc.) near the upper part
of the UV-C storage box. It may cause
malfunction to the UV-C sensor and
unnecessarily operate the UV-C
function.
NOTICE

[Press the button to turn UV-C
function off when it is not in use.
Prolonged exposure under ultraviolet
rays may change the color and shape
of the object.

['RQRWVWHULOL]HIRRG)RRGFDQQRW
be sterilized. Prolonged exposure
to ultraviolet rays may damage the
wrapping or container and affect the
food inside.
Using UV-C sterilizer system
Place the item in the UV-C storage box
and turn it on. Within 10 minutes, up to
99.9% of germs on the surface can be
removed.
1. Open the UV-C storage box while the
engine is running.
2. Press the button inside the storage
box.

[UV-C sterilizer system indicator light
illuminates.

[Antibacterial tray is ready to
operate.
3. Place the item in the center inside the
storage box and close the cover.

[UV-C indicator light illuminates.

[UV-C LED is turned on and
sterilization begins.

[After 10 minutes, the UV-C indicator
light turns off as sterilization is
complete.

[Press the UV-C sterilizer system
button to turn off the function, after
you are finished using the system.

5-151
05
Information

[2QO\SODFHWKHLWHPZKLFKUHTXLUHV
sterilization. Storing other items in the
storage box may reduce the sterilization
effect.

[89&VWHULOL]HUV\VWHPGRHVQRW
guarantee 99.9% sterilization. The
sterilization effect varies depending on
WKHGHJUHHRIH[SRVXUHWR89&OLJKW
and the shape of the item. For effective
use, change the position of the item and
run additional sterilization.

[89&LQGLFDWRUOLJKWEOLQNVRUGRHVQRW
operate properly, visit an authorized
retailer of Genesis Branded products.
Unit item verification number
Unit item verification number
Type ARegistration Number:
R-R-HdG-89910-T4AHO
Type BRegistration Number:
R-R-EpS-846R0-T4000
Type ADECLARATION OF
CONFORMITY
Type AESTABLISHMENT
NUMBER: 100891-KOR-1
CUSType ALISTING NUMBER:
E115351
Type
A/BDECLARATION OF
CONFORMITY

[This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.

[For your safety, this appliance
complies with the applicable
standards and regulations (Low
Voltage Directive, Electromagnetic
Compatibility, Environmental, etc.

[This product uses the vehicle’s battery
voltage and should be used only at DC
9 V-16 V.
WARNING
This product emits ultraviolet rays. Do
not gaze upon the UV rays while using
the product. Exposing the eyes or skin
to UV rays may have harmful effect to
the body.

6
Idle Stop and Go (ISG) ...................................................................................6-49ISG System Operation ............................................................................................... 6-49
ISG System Off............................................................................................................ 6-51
Forced to Restart Engine ...........................................................................................6-52
ISG Malfunction ..........................................................................................................6-52
Calibrating the Battery Sensor ..................................................................................6-53
Coasting .......................................................................................................... 6-54Coasting Setting ........................................................................................................ 6-54
Coasting Operating Conditions ................................................................................ 6-54
Coasting Release Conditions ....................................................................................6-55
Predictive Shift ................................................................................................ 6-56Predictive shift Operating Conditions ..................................................................... 6-56
Predictive shift off Conditions ................................................................................. 6-56
Limitations of the System ......................................................................................... 6-57
Checking Operation on the Instrument Cluster ....................................................... 6-57
How Predictive Shift Operates ................................................................................. 6-59
Drive Mode Integrated Control System ..........................................................6-61Selecting Drive Mode ................................................................................................. 6-61
ECO, COMFORT, SPORT Mode Features ................................................................. 6-62
CUSTOM Mode Features .......................................................................................... 6-63
Road Active Noise Control ............................................................................. 6-65System Malfunction .................................................................................................. 6-65
Active Sound Design....................................................................................... 6-65
Special Driving Conditions .............................................................................6-66
Hazardous Driving Conditions ................................................................................. 6-66
Rocking the Vehicle .................................................................................................. 6-66
Smooth Cornering ......................................................................................................6-67
Driving at Night ..........................................................................................................6-67
Driving in the Rain ..................................................................................................... 6-68
Driving in Flooded Areas ........................................................................................... 6-68
Highway Driving ........................................................................................................ 6-68
Winter Driving .................................................................................................6-69Snow or Icy Conditions ............................................................................................. 6-69
Winter Precautions ..................................................................................................... 6-73
Vehicle Load Limit .......................................................................................... 6-75The Loading Information Label ................................................................................. 6-75
Trailer Towing .................................................................................................. 6-79

6-43
06
Electronically Controlled Suspension
with Road Preview controls the vehicle
suspension automatically using the front
view camera and vehicle sensors to
maximize driving comfort by taking into
account the driving conditions such as
speed, surface of the road, cornering,
stopping requirements and acceleration.
Front view camera
ORS071001L
M: Front view camera
The front view camera is a sensor that
detects the front road. If the windshield
or the front view camera is covered
with snow, rain or foreign matters, the
data collected by the camera is limited
due to the degradation of the camera’s
performance. Always keep the front view
camera clean.
NOTICE

[NEVER install any accessories or
stickers on the front windshield, or
tint the front windshield.

[NEVER place any reflective objects
(for example, white paper, mirror)
over the dashboard. Any light
reflection may prevent the system
from functioning properly.

[Pay extreme caution to keep the
camera dry.

[Never disassemble the camera
assembly, or apply any impact on the
camera assembly.
Information
Have the system inspected by an
authorized retailer of Genesis Branded
products when:

[The windshield glass is replaced.

[The front view camera or cover gets
damaged or replaced.
ELECTRONICALLY CONTROLLED SUSPENSION WITH ROAD
35(9,(:

6-49
06
Idle Stop and Go helps reduce fuel
consumption by automatically shutting
down the engine, when the vehicle is
at a standstill (for example, red stop
light, stop sign, and traffic jam) subject
to certain prerequisite conditions being
satisfied as listed below.
The engine is automatically started upon
satisfying the starting conditions.
ISG system is always active, when the
engine is running.
Information
When the engine is automatically started
by ISG system, warning lights (for
example, ABS, ESC, ESC OFF, MDPS,
and parking brake warning light) may
illuminate for a few seconds due to low
battery voltage.
However, it does not indicate a
malfunction with ISG system.
ISG System Operation
Prerequisite for activation
ISG system operates in the following
situations.

[The driver's seatbelt is fastened

[The driver's door and hood are closed

[The battery sensor is activated and
the battery is sufficiently charged

[Outside temperature is not too low or
too high

[The vehicle is driven over a constant
speed and stops

[The climate control system satisfies
the conditions

[The vehicle is sufficiently warmed up

[ISG related parts are working properly

[The incline is gradual

[The steering wheel is turned less than
180 degrees and then the vehicle
stops
Information
ORS062070C
ISG system is not activated, when the
prerequisites to activate the ISG system
are unsatisfied.
Auto stop
When ISG is on the engine will be
stopped automatically when both of the
following occurs:
1. Vehicle speed decreases to 0mph (0
km/h) full stop condition.
2. Brake pedal is depressed and gear is
in D (Drive) or N (Neutral).
The Auto Stop (
) indicator illuminates
in green on the instrument cluster, when
the engine stops.
The gasoline 3.5 turbo 48 V electric
supercharger vehicle may automatically
shut down the engine when the vehicle
speed is below 16 mph (25 km/h) with
the brake pedal depressed. At this time,
the ISG indicator lights up in green on
the instrument cluster.
Information
Idle stop cannot reoccur again until the
vehicle speed goes above 3 mph (5 km/h)
and then returns again to the automatic
stop conditions as previously mentioned.
,'/(6723$1'*2

6-52
Driving Your Vehicle
Forced to Restart Engine
The engine is automatically restarted in
the following situations.

[The engine has stopped for about 5
minutes

[The air conditioning is ON with the fan
speed set to a certain high level

[The front defroster is ON

[The battery is weak

[The cooling and heating performance
of the climate control system is
unsatisfactory

[The vehicle is shifted to P (Park), N
(Neutral) or R (Reverse) when Auto
Hold is operating

[The door is opened or the seatbelt
is unfastened when Auto Hold is
activated

[The EPB switch is pressed when Auto
Hold is activated
The Auto Stop (
) indicator blinks in
green for 5 seconds on the instrument
cluster when the engine is restarted.
WARNING
When the engine is in Idle Stop mode,
the engine may restart without the
driver taking any action. Before leaving
the vehicle or working on the engine
compartment, turn off the engine by
pressing the ENGINE START/STOP
button to the OFF position.
ISG Malfunction
ISG system may not operate when there
is a malfunction with the ISG sensors or
ISG system.
The following will occur, when there is a
malfunction with the ISG system:

[The Auto Stop (
) indicator will
illuminate in yellow on the instrument
cluster.
Contact an authorized retailer of Genesis
Branded products.

6-53
06
Calibrating the Battery Sensor
If the AGM battery is reconnected or
replaced, ISG system will not operate
immediately. If you want to use the
system, the battery sensor needs to
be calibrated following the below
procedure.
ORS061023LA : Battery sensor
1. Turn off the engine.
2. Disconnect all electronic devices
that were additionally installed after
the vehicle was delivered, such as
navigation, dashcam, etc.
3. After 4 hours with the engine off, turn
the engine on and off 3 to 4 times.
Information
The ISG system may not operate in the
following situations.
-There is a malfunction with the ISG
system.
-The battery is weak.
-The brake vacuum pressure is low.
If this occurs, have the ISG system
checked by an authorized retailer of
Genesis Branded products.
NOTICE

[Use only a genuine Genesis ISG
battery for replacement. If not,
the ISG system may not properly
operate.

[Do not recharge the ISG battery with
a general battery charger. It may
damage or explode the ISG battery.

[Do not remove the battery cap. The
battery electrolyte, which is harmful
to the human body, may leak out.