tow GMC ACADIA 2009 Repair Manual

6. Make sure the tire is stored
securely. Push, pull (A), and
then try to turn (B) the tire. If the
tire moves, use the lug wrench
to tighten the cable.
Storing the Flat Tire
1. Remove the cable package from
the jack storage area.
2. Remove the small center cap by
tapping the back of the cap with
the extension of the shaft, if the
vehicle has aluminum wheels.3. Put the at tire in the rear
storage area with the valve
stem pointing toward the rear
of the vehicle.
4. Pull the cable (A) through the
door striker (E), the center of
the wheel (D), and the plastic
spare tire heat shield (C),
as shown.5. Hook the cable onto the outside
portion of the liftgate hinges (B).
6. Hook the other end of the cable
onto the outside portion of the
liftgate hinge (A).
7. Pull on the cable to make sure it
is secure.
Service and Appearance Care 5-79

8. Make sure the metal tube is
centered at the striker. Push
the tube toward the front of the
vehicle.
9. Close the liftgate and make sure
it is latched properly.
Storing the Tools
A. Tool Bag
B. Wing Bolt
C. Jack
Put back all tools as they were
stored in the jack storage
compartment and put the
compartment cover back on.
1. Ensure that the bottom of the
jack is facing toward you.
2. Turn the jack (C) on its side
and place down on the
holding bracket.3. Reinstall the wing bolt (B) by
turning clockwise.
4. To replace the cover, line up the
tab at the front of the cover with
the notch in the cover opening.
Push the cover in place and
make sure that the rear clips
are in the slots and push
the cover closed.
Store the center cap or the plastic
bolt-on wheel covers until a full
size tire is put back on the vehicle.
When you replace the compact
spare with a full-size tire, reinstall
the bolt-on wheel covers or the
center cap. Hand-tighten them over
the wheel nuts, using the lug
wrench.
5-80 Service and Appearance Care

Fabric/Carpet
Use a vacuum cleaner with a
soft brush attachment frequently
to remove dust and loose dirt.
A canister vacuum with a beater bar
in the nozzle may only be used on
oor carpet and carpeted oor mats.
For any soil, always try to remove it
rst with plain water or club soda.
Before cleaning,gently remove as
much of the soil as possible using
one of the following techniques:
For liquids: gently blot the
remaining soil with a paper towel.
Allow the soil to absorb into the
paper towel until no more can be
removed.
For solid dry soils: remove as
much as possible and then
vacuum.
To clean:
1. Saturate a lint-free, clean white
cloth with water or club soda.
2. Wring the cloth to remove excess
moisture.3. Start on the outside edge of the
soil and gently rub toward the
center. Continue cleaning, using
a clean area of the cloth each
time it becomes soiled.
4. Continue to gently rub the soiled
area until the cleaning cloth
remains clean.
5. If the soil is not completely
removed, use a mild soap
solution and repeat the cleaning
process that was used with
plain water.
If any of the soil remains, a
commercial fabric cleaner or spot
lifter may be necessary. When a
commercial upholstery cleaner or
spot lifter is to be used, test a small
hidden area for colorfastness rst.
If the locally cleaned area gives any
impression that a ring formation may
result, clean the entire surface.
After the cleaning process has been
completed, a paper towel can be
used to blot excess moisture
from the fabric or carpet.
Leather
A soft cloth dampened with water
can be used to remove dust.
If a more thorough cleaning is
necessary, a soft cloth dampened
with a mild soap solution can be
used. Allow the leather to dry
naturally. Do not use heat to dry.
Never use steam to clean leather.
Never use spot lifters or spot
removers on leather. Many
commercial leather cleaners and
coatings that are sold to preserve
and protect leather may permanently
change the appearance and feel
of the leather and are not
recommended. Do not use silicone
or wax-based products, or those
containing organic solvents to clean
the vehicle’s interior because they
can alter the appearance by
increasing the gloss in a non-uniform
manner. Never use shoe polish on
leather.
Service and Appearance Care 5-83

Rinse the vehicle well, before
washing and after to remove all
cleaning agents completely. If they
are allowed to dry on the surface,
they could stain.
Dry the nish with a soft, clean
chamois or an all-cotton towel to
avoid surface scratches and
water spotting.
High pressure car washes may
cause water to enter the vehicle.
Avoid using high pressure washes
closer than 12 inches (30 cm) to
the surface of the vehicle. Use of
power washers exceeding 1,200 psi
(8 274 kPa) can result in damage or
removal of paint and decals.
Cleaning Exterior
Lamps/Lenses
Use only lukewarm or cold water, a
soft cloth and a car washing soap to
clean exterior lamps and lenses.
Follow instructions underWashing
Your Vehicle on page 5-84.
Finish Care
Occasional waxing or mild polishing
of the vehicle by hand may be
necessary to remove residue from
the paint nish. Approved cleaning
products can be obtained from
your dealer/retailer.
If the vehicle has a basecoat/
clearcoat paint nish, the clearcoat
gives more depth and gloss to the
colored basecoat. Always use waxes
and polishes that are non-abrasive
and made for a basecoat/clearcoat
paint nish.
Notice:Machine compounding
or aggressive polishing on a
basecoat/clearcoat paint nish
may damage it. Use only
non-abrasive waxes and polishes
that are made for a basecoat/
clearcoat paint nish on the
vehicle.Foreign materials such as calcium
chloride and other salts, ice melting
agents, road oil and tar, tree sap,
bird droppings, chemicals from
industrial chimneys, etc., can
damage the vehicle’s nish if they
remain on painted surfaces. Wash
the vehicle as soon as possible.
If necessary, use non-abrasive
cleaners that are marked safe for
painted surfaces to remove foreign
matter.
Exterior painted surfaces are
subject to aging, weather and
chemical fallout that can take
their toll over a period of years.
To help keep the paint nish looking
new, keep the vehicle garaged or
covered whenever possible.
Service and Appearance Care 5-85

Protecting Exterior Bright
Metal Parts
Bright metal parts should be
cleaned regularly to keep their
luster. Washing with water is all
that is usually needed. However,
chrome polish may be used
on chrome or stainless steel trim,
if necessary.
Use special care with aluminum
trim. To avoid damaging protective
trim, never use auto or chrome
polish, steam or caustic soap
to clean aluminum. A coating of
wax, rubbed to high polish, is
recommended for all bright
metal parts.Windshield, Backglass,
and Wiper Blades
Clean the outside of the windshield
and backglass with glass cleaner.
Clean the rubber blades using a lint
free cloth or paper towel soaked with
windshield washer uid or a mild
detergent. Wash the windshield
thoroughly when you clean the
blades. Bugs, road grime, sap and
a buildup of vehicle wash/wax
treatments may cause wiper
streaking. Replace the wiper blades
if they are worn or damaged.
Wipers can be damaged by:
Extreme dusty conditions
Sand and salt
Heat and sun
Snow and ice, without proper
removal
Aluminum or
Chrome-Plated Wheels
and Trim
The vehicle may have either
aluminum or chrome-plated wheels.
Keep the wheels clean using a
soft clean cloth with mild soap and
water. Rinse with clean water.
After rinsing thoroughly, dry with a
soft clean towel. A wax may then
be applied.
Notice:Chrome wheels and
other chrome trim may be
damaged if the vehicle is not
washed after driving on roads
that have been sprayed with
magnesium, calcium or sodium
chloride. These chlorides are
used on roads for conditions
such as ice and dust. Always
wash the vehicle’s chrome with
soap and water after exposure.
5-86 Service and Appearance Care

(e)Make sure the safety belt
reminder light and safety belt
assemblies are working properly.
Look for any other loose or damaged
safety belt system parts. If you see
anything that might keep a safety belt
system from doing its job, have it
repaired. Have any torn or frayed
safety belts replaced. Also see
Checking the Restraint Systems on
page 1-61.
(f)Lubricate all key lock cylinders,
hood latch assemblies, secondary
latches, pivots, spring anchor and
release pawl, hood and door hinges,
rear folding seats, and liftgate
hinges. More frequent lubrication
may be required when exposed to a
corrosive environment. Applying
silicone grease on weatherstrips with
a clean cloth will make them last
longer, seal better, and not stick or
squeak.
(g)A fluid loss in any vehicle
system could indicate a problem.
Have the system inspected
and repaired and the fluid level
checked. Add fluid if needed.(h)Change automatic transmission
fluid if the vehicle is mainly
driven under one or more of these
conditions:
In heavy city traffic where the
outside temperature regularly
reaches 90°F (32°C) or higher.
In hilly or mountainous terrain.
When doing frequent trailer
towing.
Uses such as found in taxi,
police, or delivery service.
(i)Drain, flush, and refill cooling
system. This service can be
complex; you should have your
dealer/retailer perform this service.
See Engine Coolant on page 5-17 for
what to use. Inspect hoses. Clean
radiator, condenser, pressure cap,
and filler neck. Pressure test the
cooling system and pressure cap.
(j)Check system for interference or
binding and for damaged or missing
parts. Replace parts as needed.
Replace any components that havehigh effort or excessive wear. Do not
lubricate accelerator or cruise control
cables.
(k)Visually inspect belt for fraying,
excessive cracks, or obvious
damage. Replace belt if necessary.
(l)If driving regularly under dusty
conditions, inspect the filter at each
engine oil change.
(m)Change transfer case fluid if the
vehicle is mainly driven under
one or more of these conditions:
In heavy city traffic where
the outside temperature regularly
reaches 90°F (32°C) or higher.
In hilly or mountainous terrain.
When doing frequent trailer
towing.
Uses such as found in taxi,
police, or delivery service.
6-8 Maintenance Schedule

Services Provided

Emergency Fuel Delivery:
Delivery of enough fuel for the
vehicle to get to the nearest
service station.
Lock-Out Service:Service is
provided to unlock the vehicle if
you are locked out. A remote
unlock may be available if you
have OnStar
®. For security
reasons, the driver must present
identication before this service is
given.
Emergency Tow From a Public
Road or Highway:Tow to the
nearest GMC dealer for warranty
service, or if the vehicle was in a
crash and cannot be driven.
Assistance is also given when the
vehicle is stuck in the sand, mud,
or snow.
Flat Tire Change:Service is
provided to change a at tire with
the spare tire. The spare tire, if
equipped, must be in good
condition and properly inated. It
is the owner’s responsibility for
the repair or replacement of the
tire if it is not covered by the
warranty.
Battery Jump Start:Service is
provided to jump start a dead
battery.
Trip Routing Service:Detailed
maps of North America are
provided when requested either
with the most direct route or the
most scenic route. Additional
travel information is also
available. Allow three weeks
for delivery.
Trip Interruption Benets and
Assistance:If your trip is
interrupted due to a warranty
failure, incidental expenses may
be reimbursed during the 5 years/
100,000 miles (160 000 km)
Powertrain warranty period. Items
considered are hotel, meals, and
rental car.
Services Not Included in
Roadside Assistance

Impound towing caused by
violation of any laws.
Legal nes.
Mounting, dismounting or
changing of snow tires, chains,
or other traction devices.
Towing or services for vehicles
driven on a non-public road or
highway.
Customer Assistance Information 7-7

If a Crash Occurs
Here is what to do if you are
involved in a crash.
Check to make sure that you are
all right. If you are uninjured,
make sure that no one else in
your vehicle, or the other vehicle,
is injured.
If there has been an injury, call
emergency services for help. Do
not leave the scene of a crash
until all matters have been taken
care of. Move your vehicle only if
its position puts you in danger or
you are instructed to move it by a
police officer.
Give only the necessary and
requested information to police
and other parties involved in the
crash. Do not discuss your
personal condition, mental frame
of mind, or anything unrelated to
the crash. This will help guard
against post-crash legal action.
If you need roadside assistance,
call GM Roadside Assistance.
SeeRoadside Assistance
Program on page 7-6for more
information.
If your vehicle cannot be driven,
know where the towing service
will be taking it. Get a card from
the tow truck operator or write
down the driver’s name, the
service’s name, and the phone
number.
Remove any valuables from your
vehicle before it is towed away.
Make sure this includes your
insurance information and
registration if you keep these
items in your vehicle.
Gather the important information
you will need from the other
driver. Things like name, address,
phone number, driver’s license
number, vehicle license plate,
vehicle make, model and model
year, Vehicle Identication
Number (VIN), insurance
company and policy number, and
a general description of the
damage to the other vehicle.
If possible, call your insurance
company from the scene of the
crash. They will walk you through
the information they will need. If
they ask for a police report, phone
or go to the police department
headquarters the next day and
you can get a copy of the report
for a nominal fee. In some
states/provinces with “no fault”
insurance laws, a report may not
be necessary. This is especially
true if there are no injuries and
both vehicles are driveable.
7-12 Customer Assistance Information

Choose a reputable collision
repair facility for your vehicle.
Whether you select a dealer/
retailer or a private collision repair
facility to x the damage, make
sure you are comfortable with
them. Remember, you will have to
feel comfortable with their work for
a long time.
Once you have an estimate, read
it carefully and make sure you
understand what work will be
performed on your vehicle. If you
have a question, ask for an
explanation. Reputable shops
welcome this opportunity.
Managing the Vehicle Damage
Repair Process
In the event that your vehicle
requires damage repairs, GM
recommends that you take an active
role in its repair. If you have a
pre-determined repair facility of
choice, take your vehicle there, or
have it towed there. Specify to the
facility that any required replacement
collision parts be original equipment
parts, either new Genuine GM parts
or recycled original GM parts.
Remember, recycled parts will not be
covered by your GM vehicle
warranty.
Insurance pays the bill for the
repair, but you must live with the
repair. Depending on your
policy limits, your insurance
company may initially value the
repair using aftermarket parts.Discuss this with your repair
professional, and insist on Genuine
GM parts. Remember if your
vehicle is leased you may be
obligated to have the vehicle
repaired with Genuine GM parts,
even if your insurance coverage
does not pay the full cost.
If another party’s insurance
company is paying for the repairs,
you are not obligated to accept
a repair valuation based on
that insurance company’s collision
policy repair limits, as you have
no contractual limits with that
company. In such cases, you can
have control of the repair and
parts choices as long as cost stays
within reasonable limits.
Customer Assistance Information 7-13

Hood
Checking Things Under....... 5-9
Release............................ 5-9
Horn .................................... 3-5
How to Wear Safety Belts
Properly..........................1-18
I
Ignition Positions..................2-20
Infants and Young Children,
Restraints........................1-31
Ination - Tire Pressure.........5-41
Inator Kit, Tire....................5-56
Instrument Panel
Brightness.......................3-14
Cluster............................3-34
Overview........................... 3-4
Storage Area....................2-49
J
Jump Starting......................5-28
K
Keyless Entry System............ 2-3
Keys.................................... 2-2
L
Labeling, Tire Sidewall..........5-36
Lamp
Malfunction Indicator.........3-41
Lamps
Courtesy.........................3-14
Dome .............................3-14
Dome Lamp Override........3-14
Reading..........................3-15
Lap-Shoulder Belt................1-23
LATCH System for Child
Restraints........................1-37
License Plate Lamps............5-34
Liftgate
Carbon Monoxide.............2-10
Liftgate, Power....................2-11
Light
Airbag Readiness.............3-36
Antilock Brake System
(ABS) Warning..............3-39
Brake System Warning......3-38
Charging System..............3-37
Cruise Control..................3-44
Engine Coolant
Temperature Warning.....3-40
Fog Lamp ........................3-44
Highbeam On...................3-45Light (cont.)
Oil Pressure.....................3-44
Passenger Airbag Status
Indicator.......................3-36
Safety Belt Reminders.......3-35
Security...........................3-44
StabiliTrak
®Indicator.........3-39
Tire Pressure...................3-41
Tow/Haul Mode................3-45
Lighting
Delayed Entry..................3-15
Delayed Exit....................3-15
Entry..............................3-14
Parade Dimming...............3-15
Lights
Exterior Lamps.................3-11
Flash-to-Pass..................... 3-7
High/Low Beam Changer..... 3-7
Loading Your Vehicle............4-16
Lockout Protection................. 2-9
Locks
Delayed Locking................. 2-8
Door ................................. 2-8
Lockout Protection.............. 2-9
Power Door....................... 2-8
Programmable Automatic
Door Locks.................... 2-9
Rear Door Security Locks.... 2-9
i-6 INDEX