GMC YUKON DENALI 2009 Owner's Manual

A. Map DVD Slot
4. Touch the Insert Map Disc screen button.
The screen will tilt to access the map DVD slot.
5. Load the map DVD partway into the slot.
The system will pull it in.
6. Once the map DVD is loaded, touch the Close
screen button. The screen will close.
7. Set the search area. See “Setting the Search Area”
underGetting Started on page 1-4for more
information.
Ejecting the DVD Map Disc
When the DVD map disc is not loaded, you will not be
able to use the navigation portion of the system.
1. Press the MENU key to enter the Menu options,
then press the MENU key repeatedly until Nav is
selected or touch the Nav screen button.
2. Touch the Map Database Information screen
button.
3. Touch the Change screen button. The screen will
tilt, exposing the map DVD slot and the map DVD
will eject. Pull the disc out.
4. Touch the Close screen button. The screen
will close.
2-5

Handling the DVD Map Disc
When handling the DVD map disc, be careful of the
following:
Handle the disc very carefully to avoid
contamination or aws. Signals may not read out
properly if the disc gets contaminated or awed.
If the disc gets soiled, use a soft cloth to gently wipe
it out from the center of the disc to the outside.
Do not use photographic record cleaner, solvents,
or other cleaners.
Do not use the disc to rest on while writing or
drawing using any writing utensil or attach a seal
to any of the sides or the disc.
Do not keep the disc in direct sunlight, high
temperatures, or humidity.
After using the disc, place it back into the
original case.
DVD Map Disc Messages
If Disc Read Error appears on the display and/or the
disc comes out, it could be for one of the following
reasons:
If the map DVD disc was installed into the
audio CD/video DVD slot. See “Installing DVD
Map Disc” earlier in this section.
It is very hot. When the temperature returns to
normal, the disc should work.
You are driving on a very rough road. When the
road becomes smoother, the disc should work.
The disc is dirty, scratched, wet, or upside down.
The air is very humid. If so, wait about an hour and
try again.
Map Adjustments
The system allows you to adjust the scale of view
on the map. Also, as you drive, the map will scroll
automatically based on the direction of travel.
2-6

Map Scales
V
/U(Zoom In/Zoom Out):Touch the zoom in or
out screen buttons or the scale on the bar to change
the level of map detail. The scale will appear on the
screen once the zoom in or zoom out screen buttons are
selected. The system will adjust the map accordingly.
The scale of a map can range from 150 ft. (50 m) to
250 mi. (400 km). To change from English or metric,
see “Driver Information Center, DIC Operation and
Displays” in the Index of your vehicle’s owner manual.
Scrolling the Map
Touch anywhere on the
map screen and the scroll
symbol will appear.
Use this feature to scroll
across the map.
Move your nger in any direction on the map screen
and the map will continue to scroll in that direction until
you remove your nger.If scrolling while your vehicle is in PARK (P), the system
will scroll initially at a slower rate. It will increase if you
continue touching the map screen.
If scrolling while your vehicle is in motion, you have
one scroll speed and a limited distance to scroll.
You have to keep touching the map screen to scroll for
a longer distance.
If you have used the scroll feature to scroll the map
and your vehicle icon becomes lost, press the NAV
(Navigation) key to return to the current vehicle location
on the map.
You can use the scroll feature on the map to set a
destination. See “Pick from Map” underDestination on
page 2-15for more information.
When scrolling on the map without a planned route,
press the GO screen button to calculate the route from
your current position to the destination mark.
2-7

Symbols
The following symbols are the most common symbols
that will appear on a map screen.
Your vehicle is shown as
this symbol. It indicates the
current position and
heading direction of your
vehicle on the map.
The destination symbol
will appear on the map,
after a route has been
planned, marking your
nal destination.The waypoint symbol will
display on the map after
a waypoint has been
added to your route.
The waypoint symbol will be numbered from one
through three depending on how many intermediate
waypoints have been set.
The distance to destination
symbol indicates the
distance to your nal
destination.
This symbol only appears when time is not available or
when you are scrolling on the map.
2-8

The distance and time
to destination symbol
indicates the distance
and the estimated
time remaining to your
nal destination or arrival
time, depending on
the option selected.
The straight line to
distance symbol indicates
the straight-line distance
to your destination.
This symbol will appear before you start driving on
the route or if you are on a road where navigation
guidance cannot be given.The north up symbol
indicates the map with
North Up, known as
North Up mode.
While in North Up mode, the vehicle icon will follow the
north direction on the map regardless of which direction
the vehicle is traveling. Select this screen symbol to
switch between North Up and Heading Up modes.
The heading up symbol
indicates the map with
the vehicle travel
direction up, known as
Heading Up mode.
The shaded triangle indicates the North direction.
While in Heading Up mode, the direction your vehicle is
traveling will always be at the top of the map screen.
The vehicle icon will always be headed in the direction
your vehicle is traveling. Select this screen symbol
to switch between Heading Up and North Up modes.
2-9

The No GPS symbol will
appear when your vehicle
is not receiving a Global
Positioning System (GPS)
satellite signal.
SeeGlobal Positioning System (GPS) on page 2-46for
more information.
Select the MARK screen
button to store the location
on the screen in your
address book.
The system will automatically store the point in the
address book. See “Adding Destinations to the Address
Book” underDestination on page 2-15for more
information.Displaying Points of Interest (POI) on the
Map Screen
Select the POI screen
button to display or delete
POI icons from the map.
Displaying POI icons on the map let you know where
POIs (i.e. restaurants, gas stations, etc.) are located.
This screen will appear after selecting the POI screen
button.
2-10

Select one of the POI categories to display or to delete
POI icons from the map screen. Once a category
has been selected, the POI icon will display at the top
of the screen. Five categories can be selected to display
on the map screen. When a category is selected
those POI icons will display on the map. Press the
POI screen button again to add more POI icons.
More:Select this screen button to view more POI
categories.POI Close to:Once a category has been selected,
select this screen button to display the list of available
POIs for the selected POI categories. The list provides
the POI icon, the name, the direction, and the
distance to the POI from your vehicles current position.
Use the scroll arrows to move up and down the list.
Use the Sort by DIST. (distance), Icon, Name, and,
on Route as desired.
2-11

Go:Press this screen button, next to the desired POI,
to make this POI a destination or a waypoint.
Select a POI name to receive information about the
POI. From this screen you can select: Add to Address
Book, Go, Map, or Call (if OnStar
®personal calling
is activated).
Add to Address Book:Press this screen button to
add this POI to the address book. See “Nav” under
Configure Menu on page 2-30for information on editing
address book entries.
Go:Press this screen button to make this POI a
destination or a waypoint.
Call:Select to initiate a call using the OnStar
Hands-Free system. The Call button is only available
if OnStar personal calling is activated. For more
information about OnStar Hands-Free Calling,
see the OnStar Owner Guide.
Map:Press this screen button to display the map
showing the location of the POI.
Show:Select this screen button to update the map
screen and the list once a category has been selected.Show POI:Select ON to display the POI icons on the
map screen. Select OFF to remove the POI icons
from the map screen.
List all Categories:Select this screen button to list all
POIs sorted alphabetically.
Clear:To delete a category, do one of the following:
To delete the last added POI category, select
the Clear screen button.
To delete a specic POI category:
1. Select the category.
2. Select the subcategory.
3. A pop-up conrmation will display. Select the
Delete screen button, the map screen will
display with that POI category deleted.
Clear All:Select this screen button to clear all selected
POI categories. A pop-up conrmation will display.
Select the Delete screen button, the map screen
will display with all POI categories deleted.
2-12

Driving on a Route
When a destination has been routed and you are driving
on route, the map screen will automatically display the
next maneuver.
This next maneuver
pop-up will display the
next maneuver direction
and how many miles or
kilometers you are from it.
Dual Mode
This dual screen symbol
displays when the screen
is in dual mode.
2-13

Dual mode displays the route on half of the screen and
a maneuver or Interstate Exit list on the other half.
The Interstate Exit list advises of approaching exits.
Press this button to switch between dual screen and
full screen which displays the entire route.
When approximately 1/2 mi. (.08 km) from the next
maneuver, or two miles while on expressways,
the screen displays the name and a detailed view of the
next maneuver. Touch the dual mode button to hide
the detailed turn maneuver view for this maneuver only.Auto Reroute
When your destination is set and you are off the
planned route, the system will automatically plan a new
route and begin to reroute. You will be able to see
the new route highlighted on the screen.
Traveling Across Regions
If you plan to drive across many states, you may have
to change the region selected to represent the area
you are traveling to. To change the region, do one of
the following:
Change the selected region in the search area
when you get closer to your destination.
SeeDestination on page 2-15.
Change the selected region in the search area
when entering your destination and route settings.
SeeDestination on page 2-15.
For example, if you were traveling from Michigan to
Florida, change the region currently selected in
the search area to Florida. Enter a destination in
Florida under the Destination Entry menu.
2-14