trunk GREAT WALL FLORID 2008 User Guide

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual182
VA-882 remote controller central door lock's connection wire definition
The door lamp signal and side window signal uses a triode transistor emi\
tter open-drain output.
Headlight (+) test
Right turn signal lamp output (12 V)
Sunroof positive output (12 V) (reserve)
Power door and window negative output (100 mA)
Central door lock unlocking positive output (12 V)
Central door lock locking positive output (12 V)
Key insert diagnostic (-)
Left turn signal lamp output (12 V)
Reading lamp negative output (3.3 A)
Fastener switch lock diagnostic
Power supply ON diagnostic (12 V)
Power supply negative pole
Trunk door motor
Trunk door switch
Power supply positive pole (12 V)
Door lamp signal
Manual lock signal
Manual unlock signal
Front left door diagnostic
Front right door diagnostic
Front right door switch
Driver side door switch
Manual switch lock rocker switch
No connectionDoor lamp indicator
10 kΩ + 12 V
Ground
Connected car key ON wire
No connection
Power supply positive poleFront reading lamp
Actuator
When the actuator is at the unlock position, the inner switch is connected
Connected side window remote controller negative trigger
Power sunroof relay
Power supply 12 VDriver side door and window switch
Negative
Positive
Power supply positive pole
Headlight switch
10
22
110
1122
1
11
Controller plug front viewController socket front view
The door lamp signal and side window
signal uses a triode transistor emitter
open-drain output.
1. Headlight
Connected to the positive wire of the vehicle's headlight, this wire will hold 12 V when the headlight is turned on.
2. Right turn signal lamp
Connected to the positive wire of the vehicle's right turn signal lamp, this wire will hold 12 V when the wire is in use.
3. Sunroof positive output (reserve)
Connected to one end of the wire package of the window lift relay, this wire will output 12 V when the key is
turned to the ON position. After the key is pulled out, the wire will maintain 12 V for 60 seconds.
4. Side window negative output
Connected to the negative trigger wire of the side window remote controller, this wire will output a negative
signal for 10 seconds after the door is remotely locked by the system.
5. Central door lock unlocking output
Connected to the unlock wire of the central remote controller actuator, this wire will output 12 V when
unlocking.

Downloaded from www.Manualslib.com manuals search engine 183Electrical Accessories
6. Central door lock locking output
Connected to the locking wire of the central door lock actuator, this wire will output 12 V when locking.
7. Key insert diagnostic
Connected to the detecting wire of the lock head, the electric potential of this wire will lower when a key being
inserted into the lock is detected.
8. Left turn signal lamp
Connected to the positive wire of the left turn signal lamp, this wire o\
utputs 12 V during its use.
9. Reading lamp output
Connected to the negative trigger wire of the front reading lamp, this wire uses a low electric potential output to
control the reading lamp's lighting.
10. Fastener switch lock diagnostic
Connected to the inner switch wire of the driver side door fastener, the inside switches will be connected and the
wire's electric potential will lower when the fastener is unlocked.
11. No connection
12. Power supply ON diagnostic
Connected to the ON wire of the key switch, this wire holds 12 V when the key is turned to the ON position.
13. Power supply negative pole
Wire is grounded (too long a wire can create interference sources).
14. Trunk door motor
This wire is connected to the trunk door motor and will output 12 V when the UNLOCK button of the remote
controller or the manually unlock switch is pressed.
15. Trunk door switch
This wire is connected to the trunk door switch and will connect with the power supply's negative pole when in
use.
16. Power supply positive pole
This wire is connected to the battery positive (red fire wire).
17. No connection
18. Door lamp signal
This wire is connected to the door lamp indicator of the combination meter and holds 100 mA negative output
when in use (the indicator light is on when any door is detected open)\
.
19. Manual lock signal
This wire is connected to the locking control wire of the front left door's manual switch and will pass through
the power supply's negative pole (ground) when in use.
20. Manual unlock signal
This wire is connected to the unlocking control wire of the front left door's manual switch and will pass through
the power supply's negative pole (ground) when in use.
21. Front left door switch
This wire is connected to the front left door's switch control wire and will pass through the power supply's
negative pole (ground) when in use.
22. Front right door switch
This wire is connected to the front right door's switch control wire and will pass through the power supply's
negative pole (ground) when in use.

Downloaded from www.Manualslib.com manuals search engine 233Vehicle Body
Front Door Lock Assembly ...............................................234
Rear Door Lock Assembly ................................................237
Trunk Door Lock Assembly ...............................................239
Wiper Arm and Vent Panel Assembly ...............................240
Front & Rear Window Glasses .........................................241
Dashboard ........................................................................\
242
Cooling Unit ......................................................................246
Front Door Assembly ........................................................248
Rear Door Assembly.........................................................251
Trunk Door Assembly .......................................................254
Front Bumper....................................................................256
Rear Bumper ....................................................................259
Seat Belt ........................................................................\
...262
Seats ........................................................................\
........266
Sunroof Assembly.............................................................268
Vehicle Body

Downloaded from www.Manualslib.com manuals search engine 239Vehicle Body
Trunk door lock installation and removal
1. Install the trunk door outside handle.
Install the trunk door outside handle assembly, tighten the
mounting screw, and install the wire harness plug-in.
Trunk Door Lock Assembly
Components
2. Install the trunk door main lock assembly.
Install the trunk door main lock assembly, and tighten the
mounting screw.
3. Install the trunk lock latch.
4. For trunk lock removal, please simply reverse the
installation steps.
Trunk door lock assembly
Q1460620 (Q402) F3
Trunk door lock latch
Q2580820 + Q141F32
Q1840616F3
Trunk door outside handle assemblyConnect the central door lock controller
Connect the door lamp indicator
Q1460620 (Q402) F3
Connect the door lamp indicator
Connect the central door lock controller
Q1840616F3

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual254
Trunk Door Assembly
Components
Right side decorative blockLeft side deco-rative block
High mount brake lamp cap
Spoiler panel assembly
Trunk door assembly
High mount brake lampshade
High mount brake lamp assembly
Trunk door main lock assembly
Trunk door right side air spring
Trunk door hinge assembly
Trunk door assembly
Trunk door outside handle assembly
Trunk door plate
Trunk door handle
Trunk door protector assembly
Trunk door weatherstrip
Trunk door left side air spring
Rear wiper assembly
Trunk door glass weatherstrip
Trunk door lock button
High mount brake lamp assembly 2
Trunk door resonance block
Trunk door glass weatherstrip

Downloaded from www.Manualslib.com manuals search engine 255Vehicle Body
Trunk door removal
1. Remove the door inner decoration board.
(a) Remove the inside handle.
(b) Insert the buckle screwdriver between the fixed buckle
and the door inner decoration board to pry them loose.
Caution: Before using a buckle screwdriver, make sure
to wrap its head in tape.
(c) Take the door inner decoration board off.
2. Remove the vehicle inner lock button.
3. Remove the rear wiper arm assembly.
(a) Remove a rear wiper arm mounting bolt, and pull out
the rear wiper arm.
(b) Remove the three mounting bolts of the rear wiper mo-
tor, and pull the rear wiper motor out.
(c) Remove the rear wiper waterproof rubber plug.
4. Install it by reversing the removal steps.
Trunk door air spring removal
1. Open the trunk door.
2. Remove the air spring mounting bolts from the trunk
door.
3. Remove the air spring mounting bolts from the side
sheet metal of the rear body.
Trunk door air spring installation
Special Note: Different metals making direct contact
will accelerate corrosion. Make sure to use the correct
fastening piece to avoid premature corrosion.
1. Open the trunk door.
2. Install the air spring bracket onto side sheet metal of
the rear body with bolts.
3. Install the air spring bracket onto the side sheet metal
of the trunk door with bolts.
Trunk door protector assembly
Trunk door assembly
Rear wiper blade
Rear wiper motor
Rear wiper waterproof rubber plug
Rear wiper arm
Trunk door assembly
Trunk door left side air spring
Trunk door left side air spring
Body sheet metal
Trunk door left side air spring
Body sheet metal
Trunk door assembly