Circuit HONDA CIVIC 2003 7.G Repair Manual

PGM-FI System
I
a
DTC Troubleshooting (cont'dl
DTC Pl297: ELD Circuit Low Voltage
1. Reset the ECM {see page 11-4).
2. Start the engine.
3. Turn on the headlights.
ls DTC P1297 indicated?
YES Go to step 4.
NO Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the ELD and at the ECM.I
4. Turn the ignition switch and the headlights OFF.
5. Disconnectthe ELD 3P connector.
6. Turn the ignition switch ON {ll).
7. Measure voltage between body ground and ELD 3P
connector terminal No. 3.
ELO 3P CONNECTOB
{GRN/REDI
Wire side of female terminals
ls there about 5 V?
YES Replace the ELD. t
NO-Go to step 8.
Z3ELD
11-92
8. Turn the ignition switch OFF.
9. Disconnect ECM connector E {31P).
10. Check for continuity between body ground and
ECM connector terminal E15.
ECM CONNECTOR E 131PI
I l2l3456178I
totd/ 12021,2 2al2/tA31
ELD(GRN/RED}7\'
Wire side of female terminals
ls there continuity?
YES-Repair short in the wire between the ECM(E 15) and the ELD. r
NO- U pdate the ECM if it does not have the latest
software, or substitute a known-good ECM, then
recheck (see page 1 1-6). lf the symptom/indication
goes away with a known-good ECM, replace the
original ECM.I

DTC Pl298: ELD Circuit High Voltage
1. Resetthe ECM (see page 11-4)
2. Stan the engine.
3. Turn on the headlights.
ls DTC P1298 indicated?
YES-Go to step 4.
NO- Intermittent failure. system is OK at this time.
Check for poor connections or loose terminals at
the ELD and at the ECM.I
4. Turn the ignition switch and headlights OFF.
5. Disconnectthe ELD 3P connector.
6. Turn the ignition switch ON (ll).
7. Measure voltage between body ground and ELD 3P
connector terminal No. 1.
ELD 3P CONNECTOR
IG1 IBLK/ORNI
Wire side ot {emale terminals
ls there battery voltage?
YES-Go to step 8.
NO-Checkthe No. 4 ACG (10A)fuse in the under-
dash fuse/relay box. lf the fuse is OK, repair open in
the wire between the No. 4 ACG (10A) fuse and the
ELD.I
8.
9.
10.
11.
Turn the ignition switch OFF.
Connect ELD 3P connector terminal No. 3 to body
ground with a jumper wire.
Disconnect ECM connector E (31P).
Check for continuity between body ground and
ECM connector terminal E15.
ECM CONNECTOR E 131PI
1 21345ot/II
14LC6l/ 182C21
22123 2421 ./2Q30J
ELDIGRN/RED)i1'
Wire side of female terminals
Is thete continuity?
YES-Go to step 12.
NO Repair open in the wire between the ECM
(E15) and the ELD.
(cont'd)
ELD 3P CONNECTOR
---F-------
l1l2 :rlELD(GRN/RED)
IJUMPER wrRE
II
Wire side of temale terminals
11-93

PGM-FI System
DTC Troubleshooting (cont'd)
10. Measure voltage between ECI\4 connectorterminal
A26 and body ground.
ECM CONNECTOR A (31P)
12345617I
011 121./61,/ 18I2C2l
23 2421 m30
TDC {GRN}
Wire side oI temale terminals
ls there about 5 V ?
YES - Repair open in the wire between the ECM(426) and CMP sensor B (TDC sensor).1
NO-Go to step 11.
Turn the ignition switch OFF.
Disconnect ECIM connector A (31P)
Check for continuity between ECM connector
terminal 426 and body ground.
ECM CONNECTOR A {31PI
Wire side of female terminals
ls there continuity?
YES Repair short in the wire between the ECM(426) and the CMP sensor B (TDC sensor).1
NO Update the ECM if it does not have the latest
software, or substitute a known-good ECM, then
recheck (see page 11-6). lf the symptom/indication
goes away with a known-good ECM, replace the
original ECM.I
11.
12.
11-96
DTC Pl607: Malfunction in ECM Internal
Circuit
1. Resetthe EC|\il lsee page 11-4).
2, Turn the ignition switch ON (ll), and wait for
40 seconds.
ls DTC P 1607 indicated?
YES Update the ECM if it does not have the latest
software, or substitute a known-good ECM, then
recheck (see page 11 6). lf the symptom/indication
goes away with a known-good ECM, replace the
original ECM.I
NO Intermittent failure, system is OK at this time.
A low battery can cause this problem . Ask the
customer if there has been any recent trouble
starting the engine.l
\

MIL Circuit Troubleshooting
1. Connect an OBD ll scan tool/Honda PGM Tester
(see page 11-3).
2. Turn the ignition switch ON (ll) and read the OBD ll
scan tool/Honda PGM Tester.
Does the OBD ll scan tool/Honda PGM Tester
communicate with the ECM?
YES Go to step 3.
NO Go to troubleshooting " DLC Circuit
Troubleshooting" (see page 11-109).
3. Check the OBD ll scan tool/Honda PGM Testerfor
DTCs.
Are any DTCs ind icated?
YES Go to the DTC Troubleshooting Index.
NO-Go to step 4.
4. Turn the ignition switch OFF.
5. Turn the ignition switch ON (ll)and watch the
lMalfunction Indicator Lamp (MlL).
Does the MIL come on and stay on for more than
20 seconds aftet turning the ignition switch
oN (tr)?
YES lf the MIL always comes on and stays on, go
to step 76. But if the lMlL sometimes works
normally, first check for these problems.
. An intermittent short in the wire between the
ECIM (E29) and the data link connector (DLC).
. An intermittent short in the wire between the
ECM (E31) and the gauge assembly.
NO lf the MIL is always off, go to step 6. But if the
lvllL sometimes works normally, first check for
these problems.
. A loose No. 10 METER (7.5A) fuse in the under
dash fuse/relay box.. A loose No. 20 lG (40A) (Canada: 50A)Iuse in the
under-hood fuse/relay box.. A ioose No. 6 ECU (ECM) (15A) fuse in the under-
hood fuse/relay box.
. A loose No. 17 FUEL PUMP (15A)fuse in the
under-dash fuse/relay box.. A poor connection at ECM terminal E31.. An intermittent open in the GRN/ORN wire
between the ECM (E31) and the gauge assembly.. An intermittent short in the wire between the
ECM (A21) and the manifold absolute pressure
(MAP) sensor.. An intermittent short in the wire between the
ECI\4 (A20) and the throttle posilion (TPi sensor.. An intermittent short in the wire between the
ECM (E5) and the fuel tank pressure (FTP) sensor.
6. Turn the ignition switch OFF.
7. Turn the ignition switch ON (ll).
ls the low oil pressure light on?
YES Go to step 10.
NO-Go to step 8.
8. Inspectthe No. 10 l\4ETER (7.5A)fuse inthe under-
dash fuse/relay box.
ls the luse OK?
YES Go to step L
NO Repair shon in the wire between No. 10
METER (7.5A)fuse and the gauge assembly. Also
replacethe No. 10 METER {7.5A) fuse.l
9. Inspect the No. 20 lG1 (40A) (Canada: 50A) fuse in
the under-hood fuse/relay box.
ls the f use OK?
YES Repair open in the wire between the No. 20
lG (40A) {Canadar 50A)fuse and the gauge
assembly. lf the wire is OK, test the ignition switch
{see page 22 53).
NO Repair short in the wire between No. 20 lG
(40A) lCanada: 50A)fuse and the under'dash fusel
relay box. Also replace the No.20 lG (40Ai
(Canada: 50A) fuse.I
(conr'd)
11-97

PGM-FI System
MIL Circuit Troubleshooting (cont'dl
11.
Try to start the engine.
Does the engine start?
YES-Go to step 11.
NO-Go to step 14.
Turn the ignition switch OFF.
Connect ECM connector terminal E31 to bodyground with a jumper wire.
10.
12.
ECM CONNECTOR E 13lPI
MIL(GRN/ORN}
Wire side of female terminals
Turn the ignition switch ON (ll).
ls the M lL on?
YES Update the ECM if it does not have the latest
software, or substitute a known-good ECM, then
recheck (see page 1 1-6). lf the symptom/indication
goes away with a known-good ECIM, replace the
original ECM.I
NO-Check for an open in the wire between the
ECM (E31) and the gauge assembly. Also check for
a blown MIL bulb. lf the wires and the bulb are OK,
replace the gauge assembly.l
Turn the ignltion switch OFF,
Inspect the No. 6 ECU (ECIM) (15A) fuse in the
under-hood fuse/relay box.
ls the f use OK?
YES-Go to step 22.
NO-Go to step 16.
't 4.
15.
ll2l345617l 18I
415161,/ 1182(2t2'23 24z7l/ 12931
JUMPERWIRE
11-98
to.Remove the blown No. 6 ECU {ECfU) (154) fuse
from the under-hood fuse/relay box.
Remove the glove box (see page 20-63) and the
PGM'FI main relay 1.
Check for continuity between body ground and
PGM-Fl main relay 1 4P connector terminals No. 2
and No. 4 individuallv.
PGM-FI MAIN RELAY 14P CONNECTOR
Wrre srde ol lemale termrnals
ls there continuity?
YES-Repair short in the wire between the No.6
ECU (ECl\4) (15A) fuse and the PGM-Fl main relay 1.
Also replace the No.6 ECU (ECM) (15A) fuse.l
NO-Go to step 19.
17.
18.
fVBv) (wHr/
IA BLK)(

PGM-FI System
25.
MIL Circuit Troubleshooting (cont'dl
Check for continuity between ECM connector
terminal E9 and body ground.
ECM CONNECTOR E (31P)
Wire side o{ {emale terminals
ls therc continuity?
YES-Go to step 26.
NO Replace the No. lTFUELPUMP(15A)fuse,
and update the ECM if it does not have the latest
software. or substitute a known-good ECM, then
recheck (see page 1 1-6). lf the symptom/indication
goes away with a known-good ECM. replace the
original ECM.I
26. Remove the PGM-Fl main relay 2 (A).
11-100
27. Check for continuity between ECIVI connector
terminal Eg and body ground.
ECM CONNECTOR E 131P)
Wire side oI Jemale terminals
ls there continuity?
YES Repair short in the wire between the No. 17
FU EL PUMP (15A)fuse and the ECM (E9), or
between the No. 17 FUEL PU MP (15 A) fuse and the
PGM-FI main relay 2. Also replace the No. 17 FUEL
PUMP (15A)fuse.l
NO Go to step 28.
Remove the rear seat cushion (see page 20-80).
Remove the access panel from the floor.
Disconnect the fuel pump 5P connector.
\
28.
29.
30.

PGM-FI System
MIL Circuit Troubleshooting (cont'dl
37. lvleasure voltage between ECM/PCM connector
terminal E7 and body ground.
ECM CONNECTOR E {31PI
Wire side of female terminals
ls there battery voltage?
YES Go to step 42.
NO Go to step 38.
Turn the ignition switch OFF.
Remove the PGM-FI main relay 1
38.
39.{A}
-A
MRLY
11-102
40. lvleasure voltage between PGN4-Fl main relay 1 4P
connector terminal No. 4 and bodv qround.
PGM-FI MAIN RELAY 1ilP CONNECTOR
41.
ls there battery voltage?
YES-Go to step 41.
NO Repair open in the wire between the No. 6
ECU (ECM) (15A) fuse and the PGfM-Fl main relay 1.
I
Check for continuity between PGM-FI main relay 1
4P connector terminal No. 3 and ECM connector
terminal E7.
PGM.FI MAIN RELAY 14P CONNECTOR
\
ECM CONNECTOR E 131PI
ls there continuity?
YES-Testthe PGM-Fl main relay 1 (see page 22-
51 ). lf the relay is OK, update the ECM if it does not
have the latest software, or substitute a known-
good ECM, then recheck {see page 1 1'6). lf the
symptom/indication goes away with a known-good
ECM, replace the original ECM.I
NO*Repair open in the wire between the PGM-FI
main relay 1 and the ECM (E7).1
Wire side ot lemale terminals
MRLY (RED/YEL)
MRLY (RED/YEL)
Wire side of female terminals

PGM-FI System
MIL Circuit Troubleshooting (cont'dl
51. Measure voltage between body ground and ECM
connector terminals 44, A5, 423, and 424
individuallv.
ECM CONNECTOR A 131P)
PG2 (BLK) PG1 IBLKI
Wire side of female terminals
ls there morc than 1.0 V ?
YES Go to step 52.
NO-Repair open in the wire(s) that had more than
1.0 V between G 10'l and the ECM (A4, A5, A23,
A24l.a
Measure voltage between body ground and ECM
connector terminal 421.
ECM CONNECTOR A 131P)
Wire side of female terminals
ls there about 5 V?
YES-Go to step 60.
NO-Go to step 53.
11-104
53.
54.
Turn the ignition switch OFF.
Disconnect the manifold absolute pressure (MAP)
sensor 3P connector.
Turn the ignition switch ON (ll).
Measure voltage between body ground and ECM
connector terminal A21.
ECM CONNECTOR A {31P)
Wire side of female terminals
ls there about 5 V?
YES Replace the MAP sensor.l
NO Go to step 57.
Turn the ignition switch OFF.
Disconnect ECM connector A (31P).
55.
56.
\
57.
58.

PGM-FI System
67.
MIL Circuit Troubleshooting (cont'd)
Check for continuity between ECIM connector
terminal A20 and body ground.
ECM CONNECTOR A (31P)
rl2l3145ot/9
10t1121,/ 1,/1516ta,92A21
22 '3241 12526n
o
Wire side of female terminals
ls there continuity?
YES Repair shon in the wire between the ECN4
{A20) and the TP sensor, or repair short in the wire
between the ECM (A8) and the knock sensor. t
NO Update the ECM if it does not have the latest
software. or substitute a known-good ECM, then
recheck (see page l1-6). lf the symptom/indication
goes away with a known-good ECM, replace the
original ECM.t
vcc2{YEL/BLU}
11-106
68. Measure voltage between body ground and ECM
connector terminal E5.
ECM CONNECTOR E (31PI
Is there about 5 V?
YES U pdate the ECM if it does not have the latest
software, or substitute a known-good ECM, then
recheck (see page 11-6). lf the symptom/indication
goes away with a known-good EClvl, replace the
original ECM.t
NO-Go to step 69.
Turn the ignition switch OFF.
Disconnect the fuel tank pressure (FTP) sensor 3P
connector.
Turn the ignition switch ON (ll).
69.
70.
11.
Wire side of female terminals

DLC Circuit Troubleshooting
lf the ECM does not communicate with the OBD ll scan
tool, Honda PGfM Tester, or l/M test equipment, do this
troubleshooting procedure.
1. Measure voltage between DLC terminal No. 16 and
body ground.
DATA LINK CONNECTOR {DLCI
(WHT/RED)
Terminal side of lemale terminals
ls therc battery voltage?
YES-Go to step 2.
NO-Repair open in the wire between DLC terminal
No. 16 and the No. 9 BACK UP (7.5 A) fuse in the
under-hood f use/relay box. I
Measure voltage between DLC terminals No. 4 and
No. 16.
DATA LINK CONNECTOR (DLCI
Terminal side of Jemale terminals
Is there battery voltage?
YES Go to step 3.
NO Repair open in the wire between DLC terminal
No. 4 and body ground.l
4.
5.
3. Measure voltage between DLC terminals No. 5 and
No. 16.
DATA LINK CONNECTOR {DLC)
Terminal side of female terminals
ls there battery voltage?
YES Go to step 4.
NO- Repair open in the wire between DLC terminal
No. 5 and the ECM (E3). t
Turn the ignition switch ON {ll).
Measure voltage between DLC terminals No.5 and
No.7.
DATA LINK CONNECTOR {DLCI
Terminal side of lemale terminals
ls there 8.5 V or more?
YES Go to step 10.
NO Go to step 6.
6. Turn the ignition switch OFF.
(cont'd)
11-109