reset HONDA CR-V 2006 RD4-RD7 / 2.G User Guide

µ
µ
µ ÓÓ
´µ
The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station for about 5 seconds.
If you do nothing, the system will
scan f or the next strong station and
play it f or 5 seconds. When it plays a
station you want to listen to, press
the SCAN button again.
You can use any of f ive methods to
f ind radio stations on the selected
band:
the
preset buttons, and .
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency.
The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or SEEK button, then
release it.
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Turn the system on by
pushingthePWR/VOLknoborthe
FM/AM button. Adjust the volume
by turning the PWR/VOL knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the FM/AM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction on
AM is not available.
XM satellite radio inf ormation is
available on page .
120
Optional f or U.S. EX and SE models.
To Play the Radio SCAN
TUNE,SEEK,SCAN, AUTO SELECT
To Select a Station
TUNE
SEEK
Playing the Radio
Features
117

µ
µ If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. Each preset button can
store one f requency on AM and two
f requencies on FM.
Pick a preset button and hold it
until you hear a beep. Press the A. SEL button. ‘‘A.SEL’’
f lashes in the display, and the system
goes into scan mode f or several
seconds. It stores the f requencies of
six AM and twelve FM stations in
the preset buttons.
You will see a ‘‘0’’ displayed af ter
pressing a preset button if auto
select cannot f ind a strong station f or
every preset button.
If you do not like the stations auto
select has stored, you can store
other f requencies on the preset
buttons as previously described. To turn of f auto select, press the
A. SEL button. This restores the
presets you originally set.
1.
2.
3.
4.
Playing the Radio
AUTO SELECT
Preset
118

Playing the XMSatellite Radio (optional)
120
SCAN BUTTON
Optional on U.S. EX and SE models
CATEGORY MODE INDICATOR
PRESET BUTTONS
POWER/VOLUME
KNOB
SATELLITE RADIO
BUTTONDISPLAY
BUTTON
TUNE KNOB
SEEK/SKIP
BUTTONS
PRESET
BUTTONS

µµ
µ µ
Ó
Ó µ
´
µ
XMis a registered trademark of
XM Satellite Radio, Inc.
Satellite radio is available in U.S.
models only. Press and hold this button for more
than 2 seconds to change the mode
between the channel number and the
category.
The scan f unction samples
all channels f or 5 seconds. To
activate the function, push the SCAN
button. Push it again to get out of the
sequence.
Each preset button can
store one channel in XM1 and one in
XM2.
Push the CD/XM button, you will
see XM1 or XM2.
Use the TUNE, SEEK or SCAN
function to tune the radio to a
desired channel.
Pick a preset button and hold it
until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on XM1 and six on
XM2.
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position.
Turn the system on:
Press and release this
button to change the display. The
display will change in the f ollowing
sequence: channel name, channel
number, category, artist name, and
music title. The SEEK/SKIP
f unction selects the various
categories in XM, such as Jazz/Blues,
Rock, Classical, etc. Push the to
change the category f orward. Push
the to change the category
backward. To search f or channels
within a category, turn the TUNE
knob clockwise. Turn the TUNE knob to
change channel selection. Turn the
knob right f or higher numbered
channels and lef t f or lower
numbered channels.
When in the satellite radio mode, you can use any of three methods to
f ind channels: TUNE, SEEK/SKIP,
and SCAN.
Turn the PWR/VOL knob to adjust
the volume. Push any of the f ollowing: PWR/
VOL knob or the CD/XM button. Your vehicle is capable of receiving
XM
satellite radio anywhere in the
United States except Hawaii and
Alaska.
1.
2.
3.
4.
Satellite Digital Radio
To Play XM
Satellite Radio
SCAN
Preset
DISP SEEK /SK IP TUNE
T o Select a Channel
Playing the XMSatellite Radio (optional)
Features
Opt ional on U.S. EX and SE models
121

µÓÓ µ
µ
µ
µ
Ó
Ó
´µ
´
µ
When the CD load indicator turns
green and ‘‘LOAD’’ appears in the
screen again, insert the next CD in
the slot. Do not try to insert a CD
until ‘‘LOAD’’ appears. You could
damage the audio unit.
Repeat this until all six positions
are loaded. If you are not loading
all six positions, the system begins
playing the last CD loaded.
You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate preset
button. The system stops playing the
current CD and starts the loading
sequence. It plays the CD just loaded.
To listen to satellite radio when a CD
is playing, press the CD/XM button. Press and release the DISP
button to switch the display between
the track and disc numbers and the
elapsedtimeforthecurrentCD.
To move rapidly within a track, press
andholdthe or skipbutton. The SCAN f unction
samples all the tracks on the
selected disc in the order they are
recorded on the CD. To activate it,
press and hold the SCAN button.
You will see SCAN in the display.
You will get a 10 second sampling of
each track on the selected CD. Press
the SCAN button again to get out of
the system and play the last track
sampled.
To select a dif f erent CD, use the
appropriate preset buttons (1 to 6). This f eature plays the
tracks in random order. To activate
random play, press and release the
RDM button. You will see RDM in
the display. Press it again to return
to normal play.
To continuously replay
a track, press and release the RPT
button. You will see RPT in the
display. Press it again to turn it of f . Each time you press and
release the skip button the player
skips forward to the beginning of the
next track. Press and release the
skipbuttontoskipbackwardtothe
beginning of the current track. Press
it again to skip to the beginning of
the previous track.
4.
5.
For models with XM Radio
DISP
To Change or Select Tracks
SCAN RANDOM
REPEAT SK IP
Playing a Disc
126

You can also eject discs when the
ignition switch is of f . The disc that
was last selected is ejected f irst. To remove a dif f erent CD f rom the
changer,firstselectitwiththe
appropriate preset button. When that
CD begins playing, press the eject
button. Continue pressing the eject
button to remove all the discs from
the changer.
For inf ormation on how to handle
and protect discs, see page .
PresstheFM/AMorCDbuttonto
switch to the radio or satellite radio
while a CD is playing. To play the
CD, press the CD button again.
If a tape is in the tape player, press
the TAPE button to switch to the
tape while a CD is playing. Press the
CD button again to switch back to
theCDplayer/CDchanger.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f . To remove the disc currently in play,
press the eject ( ) button. When
a disc is removed f rom a slot, the
system automatically begins the load
sequence so you can load another
CD in that position. If you do not
remove the disc f rom the changer
within 10 seconds, the system
returns to the previous mode (AM/
FM or satellite radio). The disc will
reload into the system and will
remainthereinapausemode.
134
T o Stop Playing a CD
Removing CDs f rom the In-dash
CD Changer
Protecting Discs
Playing a Disc
Features
127

ÛÝ
Three controls f or the audio system
are mounted in the steering wheel
hub. These let you control basic
f unctions without removing your
hand f rom the wheel. The VOL switch adjusts the volume
up ( ) or down ( ). Push the
switch up or down and hold it until
the desired volume is reached, then
release it.
The MODE button changes the
mode. Pressing the button
repeatedly selects FM1, FM2, AM,
CD (if a CD is loaded), or a tape. On
models with satellite radio system,
you can also select XM1 and XM2.
If you are listening to the radio, use
the CH button to change stations.
Each time you press the button, the
system goes to the next preset
station on the band you are listening
to.If youareplayingaCD,thesystem
skips to the beginning of the next
track each time you push the CH
button. You will see the disc and
track number in the display.
If youareplayingatape,pressthe
CH button to advance to the next
selection. The system senses a silent
period, then resumes playing.
If equipped
Remote Audio Controls
Features
135
CH BUTTON
MODE BUTTON
VOL SWITCH

Your vehicle’s audio system will
disable itself if it is disconnected
f rom electrical power f or any reason.
To make it work again, you must
enter a specif ic f ive-digit code in the
preset buttons. Because there are
hundreds of number combinations
possible f rom f ive digits, making the
system work without knowing the
exact code is nearly impossible.
Youshouldhavereceivedacardthat
lists your audio system’s code and
serial numbers. It is best to store this
card in a saf e place at home. In
addition, you should write the audio
system’s serial number in this owner’s
manual.
If you lose the card, you must obtain
the code number f rom a dealer. To
do this, you will need the system’s
serial number.If you make a mistake entering the
code, do not start over; complete the
f ive-digit sequence, then enter the
correct code. You have 10 tries to
enter the correct code. If you are
unsuccessf ul in 10 attempts, you
must then leave the system on for 1
hour bef ore trying again.You will have to store your favorite
stations in the preset buttons after
the system begins working. Your
original settings were lost when the
power was disconnected.
If your vehicle’s battery is
disconnected or goes dead, or the
radio f use is removed, the audio
system will disable itself . If this
happens, you will see CODE in the
frequencydisplaythenexttimeyou
turn on the system. Use the preset
buttons to enter the five-digit code.
Thecodeisontheradiocodecard
included in your owner’s manual kit.
When it is entered correctly, the
radio will start playing.
Radio T hef t Protection
136

If your vehicle’s battery is
disconnected or goes dead, you will
need to set the clock.
Press the CLOCK button until you
hear a beep. The displayed time
begins to blink. Change the hours by
pressing the H (preset 4) button
until the numbers advance to the
desired time. Change the minutes by
press the M (preset 5) button until
the numbers advance to the desired
time.
When you are f inished, press the
CLOCK button again.
You can quickly set the time to the
nearest hour. If the displayed time
is bef ore the half hour, press the
CLOCK button until you hear a
beep, then press the R (preset 6)
button to set the clock back to the
previous hour. If the displayed
time is af ter the half hour, the
clock sets f orward to thebeginning of the next hour.
1:06 will reset to 1:00
1:53 will reset to 2:00 For example:
Setting the Clock
Features
137
RESET BUTTON
CLOCK BUTTON H BUTTON
H BUTTON CLOCK BUTTON
M BUTTON M BUTTON
RESET BUTTON
CLOCK CLOCK
U.S.modelis
shown.
U.S.: EX and SE models
Canada: EX and EX-L models
U.S.: LX model
Canada: SE model

When VSA is off, the VSA activation
indicator comes on as a reminder.
Pressing the switch again turns the
system back on.VSA is turned on every time you
start the engine, even if you turned it
off the last time you drove the
vehicle.
Driving with varying tire or wheel
sizes may cause the VSA to
malf unction. When replacing tires,
make sure they are the same size
and type as your original tires (see
page ).
If this indicator comes on while
driving, pull to the side of the road
when it is saf e, and turn of f the
engine. Reset the system by
restarting the engine. If the VSA
system indicator stays on, or comes
back on while driving, have the VSA
system inspected by your dealer.
If the indicator does not come on
when the ignition switch is turned to
the ON (II) position, there may be a
problem with the VSA system. Have
your dealer inspect your vehicle as
soon as possible.
Without VSA, your vehicle will have
normal braking and cornering ability,
but it will not have VSA traction and
stability enhancement.
This button is under the driver’s side
vent. Press it to turn the VSA system
on or of f .
If you install winter tires, make sure
they are the same size as those that
were originally supplied with your
vehicle. Exercise the same caution
during winter driving as you would if
your vehicle was not equipped with
VSA.215
VSA Of f Switch
VSA and Tire Sizes
Vehicle Stability Assist (VSA) System
Driving
171
VSA OFF SWITCH