Page 98 HONDA INTEGRA 1994 4.G Workshop Manual

Clutch Master Cylinder
Removal/lnstallation
CAUTION:
a Do not sgill b.ake lluid on the car; it may damags the
painl; it biake fluid does contact tha paint. wash it
otf immediately with water.
a Plug lhe end ot the clutch pips and r€servoil hose with
a shop towel to prsvent blake fluid ttom coming out.
1. Remove the brake fluid from the clutch master
cylinde. reservoir with a syringe.
2. Disconnect the clutch oioe and reservoir hose from
the clutch master cvlinder.
CLUICH PIPE15 N'm {1.5 kgl.m,1 1 tbf.ftl
CLUTCHMASTERCYLINDER
Pry out the cotter pin. and pull the pedal pin out ot
the yoke. Remove the nuts.
NUTS13 N.m {1.3 kgf.m,9 lbt.frl
Remove the clutch master cylinder.
NOTE: Do not spill brake fluid on the
cylinder damper.
OAMPERCLUMAIcYL
Install the clutch master cylinder in
der of removal.
NOTE: Bleed the clutch hydraulic s\
12-61.
clutch master
CLUTCHMASTERCYLINDER
!l rn Ine reverse or-
c system (see page
12-5

Pressure Plate
RING GEAR HOLDER07LAB-PVOOl OO or07924-PD20003
Removal/lnspection
Check the diaphragm spring fingers for height us-
ing the special tools and a feeler gauge.
Standard lNew): 0.6 mm (0.02 inl Max.
Service Limit: O.8 mm {O.O3 in}
FEELER GAUGE
07NAF-PR3010007936-3710100
. lf the height is more than the service limit, replace
the pressure plate.
2. Install the special tools.
3. To prevent warping, unscrew the pressure plate
mounting bolts in a crisscross pattern in several
steps, then remove the pressure plate.
CLUTCH ALIGNMENT SHAFT07NAF-PR30100HANDLE07936-3710'l OO
PRESSURE PLATE
CLUTCH ALIGNMENT OISCOTJAF_PM7011A
4.Inspect the pressure plate surface
and burning.
Inspect the fingers of the diaphrag
at the release bearing contact ar
DIAPHRAGM SPRING
Inspect for warpage using a stru
er gauge.
NOTE: Measure across the prer
pornls.
Standard (Newl: 0.03 mm (0.0
Sorvice Limit:0.15 mm (0.0O6
STRAIGHT EOGE
FEELER GAUGE
PI
lf the warpage is more than
replace the pressure plate.
6.
I surface for wear, cracks,
diaphragm spring for wear
nracr area.
PRESSURE PLAT€
straight edge and feef
pressure plate at three
0.001 in) Max.
)O6 inl
12-7

spection
release fork boot trom the clutch4. Torque the mounting bolts in a crisscross pattern as
shown. Tighten the bolts in several steps to prevent
warping the diaphragm spring.
8 x 1.25 mm25 N.m 12.6 kgt'm,19 tbt.ftl
2. Remove the release tork trom the clutch housing by
squeezing the release fork set spring with pliers. Re-
move the release bearing.
Check the release bearing for play by spinning it by
hand.
CAUTION: The release boaring i6 packed with
grease. Do not wash it in solvent.
Remove the special tools.
Recheck the diaphragm spring fingers tor height (see
page 12-7]..
Release Bearing
Removal/ln
1. Remove the
housing.
CLUTCH HOUSING
RELEASE FORK
-24/--2,t'.2424?'
IJ
l{ there is excessive plaY, rep)ace the rdease\Ear-
ing with a new one.
,F=:=

- Transmission Oil
NOTE: Check the oil with the engine OFF, and the car on
level ground.
1. Remove the oil filler plug, then check the level and
Maintenance
condition of the oil.
OIL FILLER PLUG44 N.m lia.5 kgf.m,
ORAIN PLUG$ N.m 14.0 kgf.m.29 lbf.fr)
33 tbtftlProper Level
2. The oil level must be up to the filler hole. lf it is
below the hole. add oil until it runs out, then rein-
stall rhe oil filler plug.
3. lf the transmission oil is dirty, remove the drain
plug and drain the oil.
4. Reinstall the drain plug with a new washer, and
refillthe transmission oil to the proper level.
NOTE: The drain plug washer should be replaced at
every oil change.
5 Reinstall the oil filler plug with a new washer.
OilCapacity
2.2 ( ''2.3 US.qt,1.9 lmp.qt) at oil chang€.
2-3 I l2.1Us.ql,2.0lmp.qtl at oyerhaul.
Use only SAE 10 w - 30 or '10 W - 40, API Service
SF or SG grade.
OIL FILLER PLUGa4 N.m l{.5 kgf.m, 33 lbf.ftl
Back-up Light Switch
Replacement
NOTE: To check the back-up light switch,
1. Disconnect the connector, then rem(
light switch connector trom the conn
2. Remove the back-up light switch.
BACX-UP LIGHT SWITCH25 N.m 12.5 kg[.m, 18 lbf.ftl
lnstall the new washer and the back-
Check the transmission oil level (see
Replace.
/itch, see section 23.
remove the back-up
]onnector clamp.
-up light switch.
) page 13-3).
Replace.
13-3

Transmission Assembly
Removal
Mskc aurs iack! and safoty Etands aro placod proper-
ly lsl8 saqtion 1|.
Apply parking brake tnd block rear whccl! to car
will not roll ofl stand3 and f.ll on you while wotking
undrr it.
CAUTION: Use tondcr coyar3. to avoid drmlging
plintsd 3qrfaca3,
Disconn€ct the negative {-) cable from the battery,
then the positive (+) cable.
Drain the transmission oil, then reinstall the drain
plug with a new washer (see page 13-3),
Remove the intake air duct and the air cleaner hous-
ing assembly,
AIR CITANERHOUSING
13-4
4. Disconnect the back-up light switch connoctor and
the transmission ground wir€.
5, Remove the lower radiator hose clamp trom ths
transmission hanger B.
BACK.UP LGHTsuTcH cot{t{EcToR
lnaNsMttistoNGROUND WIRE
tnaNsi ssloNHANGEB B
o.
1.
R€move the wire harness clamPs.
Disconnect the stsrt€r motor cables and the vahicla
soeed sensor (VSS) connector.
VSS OONNECTOR

lllustrated Index
Refer to the drawing below for the transmission disassembly/reassembly.
Clean all the parts thoroughly in solvent and dry with compressed air.
I ruurlcate att the parts with oil before reassembly.
NOTE:
. This transmission uses no gaskets between the major housings; use liquid gasket (P/N 08718-0001)
{see page 13-43).
a
a
Alwavs clean the magnet @ whenever the transmission housing is disassembled.
Inspect all the bearings for wear and operation.
(9
@
@
tqqlnl^'1ult I Ej
nl
11-4fi
,\|j Uh
o
@
o
@@
@
@
(3
(,
@
@
@
a
@
@
@
@
B
tg
Y
o
@
@
@
*N
13-8
[@.--oaF5i,--@:7

Mainshaft Assembly
NOTE: The 3rd/4th and the 5th svnchro hubs are installed with a press.
818Cl cngino:Inirllstion dstailr, pag. 13-27
Prior to reassembling. clean all the parts in solvent, dry them and apply lubricant to any contact surfaces, The
3rdl,lth and the sth synch.o hubs, however, should be installed with a press before lubricating them.
SYNCHRO BINGInspection, page'13_35
3RD/'TH SYNCHRO SLEEVE
3RD/'TH SYiICHRO HUB
STOPPER RING
TAPER RING
NEEDLE BEARINGlnspect for wearand operation.
SPACER
Insp6clron,page 13-35
SPRING
SYNCHRO HUBSPRING
3RD GEARInspectaon.page 13-22
NCEDE AEARINGInspocl tor wearand operalton.
SYNCHRO SI..EEVE
SYNCHROSPRING
Inspectaon.pag6 13-35
5TH GEARrnspec!on,page 13-24
4TH GCARInspection,page 13-23
SPACERCOLLAR
13-21

1_
ReassemblV
ATTACHMENT,35 mm LD.07746 - 0o30/rc0
CAUTION:
o Pless the 3rd/ilth and the 5th synchro hubs on the
msinshafi without lubrication.
. When installing the 3rd/4th and the sth synchro
hubs, support the mainshaft on the steel blocks, and
install synchro hubs using a press,
. Install the 3rd/,lth and the sth synchro hubs with a
maximum pressure of 19.6 kN (2.000 kgf, 1+466lbt).
^JOTEi Refer to page 13-21 for reassembly sequence.
Support 2nd gear on steel blocks, then install the
3rd/4th synchro hub using the special tools and a
press, as shown.
NOTE: After installing, check the operation of the
3rd/4th synchro sleeve and hub.
B18Bl sngine:
DRIVER. 40 mm l.D.07746 - 0030100
3RD/4THSYNCHRO HUB
2NO GEAR
8l8Cl engine: Assemble the 3rd/4th synchro hub and
sreeve together before installing them on the mainshaft.
3RO/4TH PRESS
SYNCHRO HU8DRIVER- 4o mm l.D.07746 - tD30100: osed end
3RD/TTHSYNCHROSLEEVE
2, Install the sth synchro
ano a press as snown.
OBIVER, ,O mm LD.0t7it6 - 003010O
ATTACHMENT,35 mm l.D.
hub using the special tools
PRESS
sTH SYNCHRO HUB
077t6 - 00304{x)
Install the ball bearing using the special tools and a
prsss as shown.
NOTE: Install the ball bearing with the tapered end
facing down.
2ND GEAR
13-27

Countershaft Assembly
lndex
NOTE:
3
The 4th and 5th gears are installed with a press.
Prior to reassembling. clean all the pans in solvent, dry them and apply lubricant to any contact surfaces. The 4th
and sth gears. however, should be installed with a press before lubricating them.
LOCKNUT ReDlace.l(E*0*10EN.m
/r1.0 - 0 - 11.0 kgtm,Il8o- o-80rbf.ft I
WASHER
BALL BEARINGInspect for wearand operat|on,
NEEDLE BEARINGInspect Ior wearand operation.
sTH GEAR
4TH GEAR
3RD GEAR
2ND GEAR
NEEDLE BEARINGInspect for wearand operation.
SPACERSelection. page 13-29
FRICTION DAMPER
DOUB1I @NESYNCHRO l818Cl .ngin.lInspection, page 13-35SYNCHRO RING lBl8Bl .ngin )Inspection, page 13-35
SYNCHRO SPBING
SYNCHRO RING
THRUSTBEARING
13-24

Countershaft Assembly
Reassembly
GAUTION:
. Pr93r 4th and 5th goar3 on the qountorshrft without
lubricrtion.
. Whon in3talling 4th and sth goa6, srpport the shaft
on st..l block3, 8nd in3tall thc 9.116 uring a prors.
. Inst.ll 4th lnd 5th gcar with a maximum pro33ur€ of
25.5 kN (2,6@ ksr. 18,806 lbo.
NOTE: Refer to page 13-28 for reassembly sequence.
Install the thrust shim and the needle bearinos on
the countershaft.
NEEDLE BEARING
THRUST SHIM
COUNTERSHAFT
Installthe friction damper. the synchro ring, and the
synchro spring on lst gear,
Install the lsv2nd synchro hub by aligning the fin-gers on the friction damper and the grooves in the'lsV2nd synchro hub, as shown.
1ST/2ND
13-32
lST GEAR
4. Install the reverse gear.
Install the synchro spring, and the double cone
synchro (818C'l engine), or synchro ring (81881
engine), as shown.
SYNCHROSPRING
REVERSEGEAfi
Assemble the friction damper, the needle bearing,
and 2nd gear, then install them by aligning the fin-gers on the friction damper and the grooves in the
1sv2nd synchro hub with the fingers of the double
cone synchro and the grooves on 2nd gear, as
shown.
2ND GEAR
NEEDLE BEARING
SPACER
FRICTION DAMPER
8.Install the parts assembled in steps 2 - 6 on the
countershaft.
Install the spacer.