HUMMER H2 2006 Owners Manual

When you have a at tire, use the following example as a
guide to assist you in the placement of wheel blocks.
The following steps will tell you next how to use the jack
and change a tire.
Removing the Spare Tire and
Tools (SUT)
Your vehicle is equipped with either jack A or jack B and it
is stored in the rear cargo compartment on the
passenger’s side of the vehicle. The tools for jack A are
also stored in the rear cargo compartment. If your vehicle
has jack B, the tools are stored under the rear
passenger’s seat.
Removing Jack A and Tools (SUT)
To remove the cover, unlock it and then pull the
cover off.
Remove the tool kit/rst aid kit to gain access to the tire
changing equipment.
5-71

Once it is removed, you will see the following tire
changing equipment:
A. Tool Bag
B. Jack
C. Jack Wing NutD. Wing Nut Retaining
Wheel Blocks
E. Wheel BlocksTo remove the equipment, do the following:
1. Unscrew the wing nut (D) retaining the wheel blocks
and remove them.
2. Unscrew the wing nut (C) retaining the jack and
remove it.
3. Pull the tool bag (A) up and out from the front
retention clip. Jack A and Tools
5-72

4. Open the tool bag. You will nd the following
tools needed to remove the spare tire and change
a at tire:
A. Jack Handle
B. Jack Handle Extension (Used for Rear Flats Only)
C. Wheel Wrench
D. Ratchet
Before proceeding, be sure to set the wheel blocks at
the appropriate tires as previously shown.Removing Jack B and Tools (SUT)
To remove the cover, unlock it and then pull the
cover off.
Remove the tool kit/rst aid kit to gain access to the tire
changing equipment. Jack A Tools
5-73

Once it is removed, you will see the following:
Release the jack by turning the end of the jack handle
counterclockwise.
To remove the tools, do the following:
1. Pull the bottom of the driver’s side second row seat
up to access the tools. See60/40 Split Bench Seat
on page 1-6for more information.2. Remove the strap from the seat rail. Then
carefully slide the tool bag out from under the
seat rail as shown.
Take care to not pinch the seat cables or electrical
harnesses. Jack B
5-74

3. Open the tool bag. You will nd the following tools
needed to remove the spare tire and at tire:
A. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel WrenchD. Wheel Wrench
Extension
E. Wheel BlocksBefore proceeding, be sure to set the wheel blocks at
the appropriate tires as previously shown.
To use a wheel block, lift
the wheel block as shown
to lock it into place.
Jack B Tools
5-75

Removing the Spare Tire (SUT)
The spare tire is attached to the tire carrier. To remove
the spare tire, do the following:
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-14for tire carrier operation.
2. Unscrew the wing nut on the back of the tire carrier.3. Pull off the license plate holder from the spare tire.
4. For jack A, slide the ratchet onto the wheel
wrench with the DOWN mark facing you. For jack B,
attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts.
5-76

5. Turn the ratchet counterclockwise to loosen the
wheel nuts.Or, turn the wheel wrench with the wheel wrench
extender (jack B) counterclockwise to loosen
the wheel nuts.
6. Remove the three wheel nuts holding the spare tire
onto the tire carrier.
7. Pull off and gently lower the spare tire to the
ground. Set it next to the at tire. Jack A Tools
Jack B Tools
5-77

Removing the Spare Tire and
Tools (SUV)
Removing the Jack (SUV)
Your vehicle is equipped with either jack A or jack B.
The jack (A or B) is stored behind the driver’s side
second row seat.
1. Fold the driver’s side second row seat down to
access the jack. See60/40 Split Bench Seat on
page 1-6for more information.
2. For jack A, turn the
wing nut
counterclockwise to
release it. Then
remove the bracket
retaining the jack.For jack B, turn the
jack handle end
counterclockwise
to release it.
3. Grasp and lift the jack out of the bracket.
Jack A
Jack B
5-78

Removing the Tools (SUV)
The equipment you will need is located under the
driver’s side second row seat. To remove the equipment,
do the following:
1. Make sure nothing is under the front of the driver’s
side second row seat.
2. Locate the tools by lifting the driver’s side second
row seat up to expose the oor. See60/40 Split
Bench Seat on page 1-6for more information.
3. For the jack A tool bag, carefully slide the tool bag
under the seat rail to remove it from the vehicle.For the jack B tool bag, remove the strap from the
seat rail. Then carefully slide the tool bag out
from under the seat rail as shown.
Jack A Tool Bag
Jack B Tool Bag
5-79

4. Open the tool bag. You will nd the following tools
needed to remove the spare tire and at tire:
A. Jack Handle
B. Jack Handle
Extension (2)
(Used for Rear
Flats Only)C. Wheel Wrench
D. RatchetA. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel WrenchD. Wheel Wrench
Extension
E. Wheel Blocks
Jack A Tools
Jack B Tools
5-80