display HUMMER H2 2007 Manual PDF

If there is a decreased audio signal during CD,
MP3, or DVD play, there could be a soft hissing
noise through the speakers and/or headphones.
If the hissing sound in the wireless headphones
seem excessive, make sure the headphone
batteries are fully charged. A small amount of
hissing is normal.
Battery Replacement
To change the batteries, do the following:
1. Press down on the left earpiece and slide the
battery compartment panel down to expose
the battery compartment.
2. Replace the two AAA batteries in the
compartment. Make sure they are installed
correctly using the diagram on the inside
of the battery compartment.
3. Slide the battery compartment panel back and
then down until the panel closes into the
headphone ear piece.
If the headphones are to be stored for a long
period of time, remove the batteries, and keep
them in a cool, dry place.
Wired Headphones
There is a headphone jack on the left lower side
of the video screen. Use this jack with universal
wired headphones. To adjust the volume, do
the following:
1. Press the power button on the monitor to turn
the video screen on. Briey press the power
button again to toggle between monitor and
DVD control buttons. The appropriate toggle is
monitor. Main menu function icons display.
2. Plug the headphone into the corresponding
jack, located on the bottom left of the video
screen, next to the auxiliary jack.
3. Press the soft key buttons on the monitor,
located under the up and down arrow icons,
to increase or to decrease the volume.
Audio Output
Audio from the DVD player or auxiliary devices
can be heard through the vehicle speakers or the
wireless/wired headphones. The FM Modulator
control has to be set to one of eight frequencies in
order for these devices to be heard through the
vehicle’s speakers. See “FM Modulator Control”
later in this section.
273

Each video screen can be powered on or off
independently. Make sure the screens are off when
not in use.
Briey press the power button again to toggle
between monitor and DVD control buttons.
The appropriate toggle is monitor. Main menu
function icons display.
SOURCE:Press the soft key button on the
monitor, located under the SOURCE icon to switch
between the different sources listed below:
AV (Audio/Video) 1 — Allows the head
restraint-mounted DVD player to become
a source. This input views the DVD player
directly inside the screen being viewed.
AV (Audio/Video) 2 — Allows the head
restraint-mounted DVD player to become a
source. This input views the DVD player inside
the alternate head restraint.
AV (Audio/Video) 3 — Allows the
screen-mounted auxiliary input jack to become
a source. This input can only be viewed on
the screen it is connected to.
Each video screen can be adjusted independently
to switch between all available audio/video sources.MENU:Press the soft key button on the monitor,
located under the MENU icon, to adjust the
video screen control functions such as:
CONTRAST — Adjusts picture contrast.
BRIGHTNESS — Adjusts picture brightness.
COLOR — Adjusts picture color balance.
TINT — Adjusts picture tint.
SHARPNESS — Adjusts picture sharpness.
MODE — Adjusts screen preference from
Normal to Wide, or to Zoom.
RESET DEFAULT — Resets all monitor
control functions to default (center point)
settings.
Q(Up):Press the soft key button on the monitor,
located under the up arrow icon, to increase a
basic monitor control function once the menu
button is pressed and a control function is
selected.
R(Down):Press the soft key button on the
monitor, located under the down arrow icon, to
decrease a basic monitor control function once the
menu button is pressed and a control function is
selected.
275

DVD Player
The DVD player is located inside each head
restraint behind the screens. To access the DVD
player, press on the top center of the monitor
(around the HUMMER name badge). The screen
tilts outward exposing the DVD loading slot.
The DVD player can be controlled by the buttons
on the screen or by the buttons on the system’s
remote control. See “Remote Control” later in this
section for more information.The RSE system DVD player is only compatible
with DVDs of the correct region code for the
country where the vehicle was sold. The DVD
region code is printed on the jacket of most DVDs.
DVDs, Standard audio CDs, CD-R, CD-RW,
enhanced CDs, video CDs, and CD-ROM with
MP3 media are supported by this DVD player.
DVD+R, DVD+RW, and copy protected CDs might
or might not be supported by the DVD player.
The DVD player does not support DVD-RAM,
DVD-ROM, DVD-R, DVD-R/W, and DVD audio
media. An error message displays if this type
of media is inserted into the DVD player.
If an error message displays on the video screen,
see “DVD Messages” later in this section.
277

DVD Control Buttons
To bring up the DVD control buttons, briey press
the power button located on the face of the
monitor. This toggles the on-screen soft key
choices to either monitor or DVD control.
If the power button is pressed for more than
two seconds, the power could turn off.
AV Input Jack (Audio/Video Input Jack):The
audio/video input jack allows viewing of auxiliary
sources such as portable DVD players, gamestations, or video cameras, on each monitor
individually. The AV input jack is located on the
lower left side of the monitor and is identied
on the monitor as the AUX (auxiliary) input jack.
P(Power):Press this button to turn the DVD
player on and off. Press this button briey to toggle
between monitor and DVD on-screen functions.
X(Eject):The eject button is located on the
DVD player next to the DVD loader slot. Press this
button to eject the disc. If the ejected disc is
partially left in the DVD player, the disc does not
reload until it is pushed back into the player.
r(Play):Press the soft key button on the
monitor, located under the play symbol to start
playback of a disc. On DVDs and video CDs with
playback control (PBC), menu screens can display
automatically. It might be necessary to press the
play soft key button again to begin playing.
There is a play position memory feature for DVD
and video CD only. If the DVD player is turned off
and then turned back on, the DVD player resumes
playback from the same point it stopped. The play
position memory is erased if the disc is removed.
278

c(Stop):Press the soft key button on the
monitor, located under the stop symbol to stop
playing, rewinding, or fast forwarding a disc. The
disc position automatically stores in memory.
There is a pre-stop feature for DVD and video CD
only. This feature lets the disc resume playback
from the position where it was stopped. Press the
stop soft key button once during disc playback
and the stop icon displays on the DVD startup
screen. This icon disappears after a few seconds.
Press the stop soft key button a second time,
or eject the disc, to cancel the pre-stop feature and
to clear the disc position memory.
Playing a Disc
To play a disc, insert the disc partially into the
loading slot. The DVD player automatically draws
the disc in and playback starts. Make sure the
disc is inserted with the printed side facing the rear
of the vehicle. If the disc is inserted wrong, the
DVD player automatically ejects that disc and
displays No Disc, on the video screen. Once the
playback begins, Loading displays on the
screen along with a disc indicator.If a disc is already in the player, make sure to
press the play soft key button on the monitor
faceplate after the monitor buttons have been
toggled to the DVD control mode. If operating the
disc through the system’s remote control, select
the corresponding DVD button, DRIVER or PASS
for the DVD player that you want to control.
Some DVDs do not allow fast forwarding or
skipping of the copyright information or previews.
Some DVDs begin playing after the previews
have nished. If the DVD does not begin playing
at the main title, refer to the on-screen instructions.
Ejecting a Disc
Press the center on the upper monitor to gain
access to the DVD loader slot and press the eject
button, to eject the disc. As the disc ejects, the
display on the screen indicates Open.
If a disc is ejected from the player, but not removed,
the disc does not reload until it is pushed back into
the player. Another way to reload a disc that has
been ejected, but not removed from the DVD
player, is to either press the eject button or the
play soft key button. The DVD player automatically
reloads the disc and displays Close on the
video screen.
279

SOURCE:Press this button to select between the
available audio/video sources. Each video
screen can be adjusted independently to switch
between all audio/video sources.
ZOOM:Press this button to toggle between the
screen zoom selections available on the monitor’s
main menu. Choose from ZOOM SCREEN,
NORMAL SCREEN, or WIDE SCREEN.
To show what each zoom function does, see the
following selections:
ZOOM SCREEN: Expands a full frame
formatted DVD to t the entire monitor
by stretching only the left and right side video
information and leaving black stripes at the
top and bottom of the monitor.
NORMAL SCREEN: Displays any formatted
DVD. Playing a full frame formatted DVD shows
black stripes at the left and right sides of the
monitor. Playing a widescreen formatted DVD
shows black stripes on all sides of the monitor.
WIDE SCREEN: Expands a full frame
formatted DVD to t the entire monitor. It
proportionally stretches a widescreen formatted
DVD to t the entire width, leaving black stripes
at the top and bottom of the monitor.
Q(Up):Press this button to increase the
basic monitor control functions once the monitor
PICTURE button is pressed and a control function
is selected.
R(Down):Press this button to decrease the
basic monitor control functions once the monitor
PICTURE button is pressed and a control function
is selected.
Remote Control Buttons
(DVD Control Functions)
SETUP:Press this button to modify default
settings to suit your personal preferences. For
further information on modifying the default
settings, see “RSE On-Screen Display (OSD)
Menu” later in this section.
ENTER:Press this button to enter a selected
function.
Q,R,q,r(Directional Arrows):Press these
buttons to move through the DVD menus.
The up and down arrows move through MP3
folders.
281

PLAYr:Press this button to start playback of
the DVD.
PAUSE
j:Press this button to pause a
viewed image.
STOP
c:Press this button to stop playback of
the DVD.
PREV
g(Previous):Press this button to return
to the beginning of the chapter or track that is
currently playing. Press this button again to return
to the previous chapter or track. While playback
is in pause mode, press and release this
button multiple times to return to the previous
scenes one by one.
FR/FF
r[(Fast Rewind/Fast Forward):
Press the left arrow to fast rewind the DVD. Press
and release this button multiple times to increase
the rewind speed in sequence at 2, 4, 8, 16,
and 32 times of normal speed. To stop rewinding,
press the STOP button. This button might not
work when the DVD is playing the copyright
information or the previews.Press the right arrow to fast forward the DVD
during play or pause. Press and release this button
multiple times to increase the forward direction
speed in sequence at 2, 4, 8, 16, and 32 times of
normal speed. To stop fast forwarding, press
the STOP button. This button might not work when
the DVD is playing the copyright information or
the previews.
NEXT
l:Press this button to advance to the
beginning of the next chapter or track. While
playback is in pause mode, press and release this
button multiple times to advance the scenes
one by one.
SLOW
p:Press this button to review in slow
motion during play or pause. Press and release
this button multiple times to decrease the review
speed in sequence at 1/2, 1/4, or 1/8 times of
normal speed.
MENU:Press this button to enter the DVD disc
menu while the disc is playing. The type of
menu displayed depends on the disc.
TITLE:Press this button to enter the disc title
mode with a disc loaded. The title feature is
disc-specic, and might not be available with the
disc that is currently loaded in the DVD player.
282

A-B:This button is used to repeat predened
sections. Press this button once while the disc is
playing to select the starting position. Press a
second time to select the end position. Press a
third time to turn the function off.
GO:Press this button to access scenes directly
by entering the time/title/chapter.
SUBTITLE:Press this button to switch between
the default language set on the DVD player and up
to any alternate language that could be recorded
on the DVD disc itself. Press this button again
to turn the subtitle function off.
PBC (Playback Control):Press this button to
turn video CD playback control on or off.
ZOOM:Press this button to zoom in on video
images during play or pause modes. Press
and release this button multiple times to increase
the image size in sequence, at 1, 2, or 3 times
of normal size, or ZOOM OFF.
In zoom modes, the direction arrow buttons can be
used to change the zoomed monitor viewing area.RETURNq:Press this button to go back
one step in the RSE On-Screen Display (OSD)
menu and some DVD menus. Press this button
to exit the current menu and to go to the
previous menu.
MUTE
$:Press this button to mute the audio
sound output.
DISP. (Display):Press this button to switch
between display functions of elapsed/remaining
time, full information, or off.
REPEAT
k:Press this button to switch between
repeat functions of title, chapter, track, entire
disc, or off.
AUDIO:Press this button to switch between the
default language set on the DVD player or to
any alternate language that could be recorded on
the DVD disc itself.
Numeric Keys:The numbered buttons located on
the lower left side of the system’s remote control
are numerical digits assigned to menu options.
To use the numeric buttons, follow the menu
instructions by pressing the number that has been
assigned to the preferred option.
283

Battery Replacement
To change the remote control batteries, do the
following:
1. Slide the battery door, located on the back of
the remote control, down.
2. Replace the two AAA batteries in the
compartment. Make sure they are installed
correctly, using the diagram on the inside
of the battery compartment.
3. Close the battery door.
If the remote control is to be stored for a long
period of time, remove the batteries and keep them
in a cool, dry place.
Using the RSE On-Screen
Display (OSD) Menu
To use the RSE OSD menu while using the DVD
player or an auxiliary device, do the following:
1. Press the SETUP button on the system’s
remote control to access the general setup
menu, see “Remote Control” earlier in
this section.
2. Once this menu is on the screen, press the
directional arrows and then the ENTER
button to navigate the screen.
This menu lets you select default preferences
for language, video, audio, and ratings.
Not all DVDs support all of the feature defaults
in the setup menus. If a feature is not
supported, the defaults are provided by the
DVD media.
The default language selection applies to all
future DVDs.
3. Press the RETURN button on the system’s
remote control to exit this menu, or wait for
the menu to time out.
284

To use the RSE OSD menu while using a CD or
an MP3, do the following:
1. Make sure a CD or an MP3 is loaded in the
RSE system and that the system is not in
auxiliary, then press the SETUP button on the
system’s remote control.
2. Once the general setup menu is on the
screen, press the directional arrows on
the system’s remote control and then the
ENTER button to navigate the screen.
This menu lets you select default preferences
for language and playback settings.
3. Press the RETURN button on the system’s
remote control to exit this menu, or wait for
the menu to time out.Advanced MP3 CD Menu Displays and
Operation
To use the RSE OSD menu for advanced MP3
CD menu displays and operation, do the following:
1. Insert an MP3 CD and then select it for
playback from the RSE on-screen display
menu. The name of the folder shows on the
monitor’s top line and the names of songs
show in columns underneath.
When an MP3 is selected for play, all les
and folders are accessed in the order in which
they were written to the CD. Because of
this, the order in which they are expected to
play might not match the order in which
they are actually played.
2. Press the directional arrows on the system’s
remote control to help navigate through the
folders, then press ENTER or PLAY to
start playing a selection.
3. You can also press the GO button on the
system’s remote control to directly access
the Songs. See “GO” under Remote Control
Buttons (DVD Control Functions) earlier in
this section.
285