load capacity HUMMER H3 2009 Owners Manual

Page 114 of 382

Luggage Carrier
If the vehicle has this feature, cargo
can be loaded on top of the vehicle.
The luggage carrier consists of
siderails attached to the roof.
The crossrails attach into the
siderails and can be moved back
and forth to accommodate various
cargo sizes.
Notice:Loading cargo on the
luggage carrier that weighs more
than 250 lbs. (113 kg) or hangs
over the rear or sides of the
vehicle may damage the vehicle.
Load cargo only on top of the
crossrails and tie the cargo down
to the crossrail support cargo
tie-down loops, making sure
to fasten it securely
Do not exceed the maximum vehicle
capacity when loading your vehicle.
For more information on vehicle
capacity and loading, seeLoading
the Vehicle on page 4-35.Adjusting the Crossrails
To adjust the crossrails to t a load:
1. Turn the crossrail key
counterclockwise to unlock the
crossrail end cap.
2. Remove the end cap.
3. Pull the lever labeled “PULL”
from left to right to loosen the
crossrail.
4. Repeat Steps 1 through 3 to the
opposite end of the crossrail.5. Once both sides of the crossrail
are loose, adjust the crossrail to
the desired position.
6. Push the lever labeled “PULL”
from right to left to lock the
crossrail in place.
7. Reinstall the end cap and turn
the crossrail key to lock the
crossrail.
8. Repeat Steps 5 through 7 to the
opposite end of the crossrail.
Stop Tabs
If the vehicle has a sunroof, it has a
crossrail stop tab in the siderail.
This tab prevents the crossrail from
being moved past the opening of
the sunroof and cargo from
being loaded too far forward.
The vehicle may have cargo tie
downs. Once the cargo is loaded
onto the crossrails, use the cargo tie
downs to secure it. Do not load
cargo directly on the roof of the
vehicle. SeeCargo Tie Downs on
page 2-49for more information.
2-48 Features and Controls

Page 217 of 382

If the vehicle has a brush guard,
never tow or apply any loads
onto the brush guard.
Loading the Vehicle
It is very important to know how
much weight the vehicle can
carry. This weight is called the
vehicle capacity weight and
includes the weight of all
occupants, cargo and all
nonfactory-installed options.Two labels on the vehicle show
how much weight it may
properly carry, the Tire and
Loading Information label and
the Certication/Tire label.
{CAUTION
Do not load the vehicle any
heavier than the Gross Vehicle
Weight Rating (GVWR), or
either the maximum front or
rear Gross Axle Weight Rating
(GAWR). If you do, parts on
the vehicle can break, and it
can change the way your
vehicle handles. These could
cause you to lose control and
crash. Also, overloading can
shorten the life of the vehicle.
Tire and Loading Information
Label
A vehicle specic Tire and
Loading Information label
is attached to the vehicle’s
center pillar (B-pillar). With the
driver’s door open, you will
nd the label attached below the
door latch post.
Label Example
Driving Your Vehicle 4-35

Page 218 of 382

The Tire and Loading
Information label shows the
number of occupant seating
positions (A), and the maximum
vehicle capacity weight (B) in
kilograms and pounds.
The Tire and Loading Information
label also shows the size of the
vehicle’s original equipment
tires (C) and the recommended
cold tire ination pressures (D).
For more information on tires and
ination seeTires on page 5-44
andInflation - Tire Pressure on
page 5-51.
There is also important
information on the
Certication/Tire label. It tells
Gross Vehicle Weight Rating
(GVWR) and the Gross
Axle Weight Rating (GAWR)
for the front and rear axles. See
“Certication/Tire Label” later
in this section.Steps for Determining Correct
Load Limit
1.
Locate the statement “The
combined weight of occupants
and cargo should never
exceed XXX kg or XXX lbs” on
your vehicle’s placard.
2.Determine the combined
weight of the driver and
passengers that will be riding
in your vehicle.
3.Subtract the combined weight
of the driver and passengers
from XXX kg or XXX lbs.
4.The resulting gure equals the
available amount of cargo and
luggage load capacity. For
example, if the “XXX” amount
equals 1400 lbs and there will
be ve 150 lb passengers in
your vehicle, the amount
of available cargo and
luggage load capacity is
650 lbs (1400−750
(5 x 150) = 650 lbs).
5.Determine the combined
weight of luggage and
cargo being loaded on the
vehicle. That weight may not
safely exceed the available
cargo and luggage load
capacity calculated in Step 4.
6.If your vehicle will be towing a
trailer, the load from your
trailer will be transferred to
your vehicle. Consult
this manual to determine how
this reduces the available
cargo and luggage load
capacity of your vehicle.
SeeTowing a Trailer
on page 4-42for important
information on towing a
trailer, towing safety, and
trailering tips.
4-36 Driving Your Vehicle

Page 219 of 382

A.Vehicle Capacity Weight for
Example 1=1,000 lbs
(453 kg).
B.Subtract Occupant Weight
150 lbs (68 kg)×2=300 lbs
(136 kg).
C.Available Occupant and
Cargo Weight=700 lbs
(317 kg).
A.Vehicle Capacity Weight for
Example 2=1,000 lbs
(453 kg).
B.Subtract Occupant Weight
150 lbs (68 kg)×5=750 lbs
(340 kg).
C.Available Cargo
Weight=250 lbs (113 kg).
A.Vehicle Capacity Weight for
Example 3=1,000 lbs
(453 kg).
B.Subtract Occupant Weight
200 lbs
(91 kg)×5=1,000 lbs
(453 kg).
C.Available Cargo
Weight=0 lbs (0 kg).
Refer to the vehicle’s Tire and
Loading Information label
for specic information about the
vehicle’s capacity weight and
seating positions.
Example 1Example 2Example 3
Driving Your Vehicle 4-37

Page 220 of 382

The combined weight of the
driver, passengers, cargo
and any accessories or
equipment added to the vehicle
after it left the factory should
never exceed the vehicle’s
capacity weight.
Certication/Tire Label
A vehicle specic
Certication/Tire label is
attached to the bottom section
of the center pillar (B-pillar),
on the driver’s side of the
vehicle. The label shows the
Gross Vehicle Weight Rating
(GVWR). The GVWR includes
the weight of the vehicle, alloccupants, fuel, cargo and trailer
tongue weight, if pulling a
trailer.
The Certication/Tire label also
tells the maximum weights
for the front and rear axles,
called Gross Axle Weight Rating
(GAWR). To nd out the
actual loads on the front and
rear axles, go to a weigh station
and weigh the vehicle. Your
dealer/retailer can help with this.
Be sure to spread out the
load equally on both sides of the
centerline.
Never exceed the GVWR for the
vehicle, or the GAWR for
either the front or rear axle.
If the load is heavy, it should be
spread out.
Similar appearing vehicles may
have different GVWRs and
capacity weights. Please note
the vehicle’s Certication/Tire
label or consult your
dealer/retailer for additional
details.{CAUTION
Do not load the vehicle any
heavier than the Gross Vehicle
Weight Rating (GVWR), or
either the maximum front or
rear Gross Axle Weight Rating
(GAWR). If you do, parts on
the vehicle can break, and it
can change the way your
vehicle handles. These could
cause you to lose control and
crash. Also, overloading can
shorten the life of the vehicle.
Using heavier suspension
components to get added
durability might not change the
weight ratings. Ask your
dealer to help you load the
vehicle the right way.
Label Example
4-38 Driving Your Vehicle

Page 227 of 382

Weight of the Trailer Tongue
The tongue load (A) of any trailer is
an important weight to measure
because it affects the total gross
weight of the vehicle. The Gross
Vehicle Weight (GVW) includes the
curb weight of the vehicle, any
cargo carried in it, and the people
who will be riding in the vehicle.If
there are a lot of options, equipment,
passengers or cargo in the vehicle,
it will reduce the tongue weight
the vehicle can carry, which will also
reduce the trailer weight the
vehicle can tow. If towing a trailer,
the tongue load must be added
to the GVW because the vehicle will
be carrying that weight, too. See
Loading the Vehicle on page 4-35
for more information about the
vehicle’s maximum load capacity.The trailer tongue weight (A) should
be 10 percent to 15 percent of
the total loaded trailer weight (B), up
to a maximum of 500 lbs (227 kg)
with a weight carrying hitch or
a weight distributing hitch.
Do not exceed the maximum
allowable tongue weight for the
vehicle. Choose the shortest hitch
extension that will position the
hitch ball closest to the vehicle.
This will help reduce the effect of
trailer tongue weight on the
rear axle.If the spare tire carrier is mounted
on the back of the vehicle and
the hitch extension is too short,
the spare tire may interfere
with trailer coupling or trailer tongue
jack operation on some types of
trailers.
After loading the trailer, weigh the
trailer and then the tongue,
separately, to see if the weights are
proper. If they aren’t, adjustments
might be made by moving some
items around in the trailer.
Driving Your Vehicle 4-45

Page 228 of 382

Total Weight on the Vehicle’s
Tires
Be sure the vehicle’s tires are
inated to the upper limit for cold
tires. These numbers can be found
on the Certication/Tire Label
located on the B-pillar below the
door latch or seeLoading the
Vehicle on page 4-35. Make sure
not to go over the GVW limit for the
vehicle, or the GAWR, including
the weight of the trailer tongue. If
using a weight distributing hitch,
make sure not to go over the rear
axle limit before applying the weight
distribution spring bars.
Hitches
It is important to have the correct
hitch equipment. Crosswinds,
large trucks going by and rough
roads are a few reasons why
the right hitch is needed.Weight-Distributing Hitches and
Weight Carrying Hitches
When using a weight-distributing
hitch, the hitch must be adjusted so
that the distance (A) remains the
same both before and after coupling
the trailer to the tow vehicle.
Trailering may also be limited by the
vehicle’s ability to carry tongue
weight. Tongue weight cannot cause
the vehicle to exceed the GVWR(Gross Vehicle Weight Rating) or
the RGAWR (Rear Gross Axle
Weight Rating). The effect of
additional weight can reduce the
trailering capacity more than
the total of the additional weight.
Consider the following example:
A vehicle model base weight
is 5,500 lbs (2 495 kg); 2,800 lbs
(1 270 kg) at the front axle and
2,700 lbs (1 225 kg) at the rear axle.
It has a GVWR of 7,200 lbs
(3 266 kg), a RGAWR of 4,000 lbs
(1 814 kg) and a GCWR (Gross
Combination Weight Rating)
of 14,000 lbs (6 350 kg). The trailer
rating should be:
Expect tongue weight to be at least
10 percent of trailer weight
(850 lbs (386 kg)) and because the
weight is applied well behind the (A) Body-to-Ground Distance (B)
Front of Vehicle
4-46 Driving Your Vehicle

Page 229 of 382

rear axle, the effect on the
rear axle is greater than just the
weight itself, as much as 1.5 times
as much. The weight at the rear
axle could be 850 lbs (386 kg)
X 1.5 = 1,275 lbs (578 kg). Since
the rear axle already weighs
2,700 lbs (1 225 kg), adding
1,275 lbs (578 kg) brings the total to
3,975 lbs (1 803 kg). This is very
close to, but within the limit for
RGAWR as well. The vehicle is set
to trailer up to 8,500 lbs (3 856 kg).If the vehicle has many options and
there is a front seat passenger
and two rear seat passengers with
some luggage and gear in the
vehicle as well, 300 lbs (136 kg)
could be added to the front
axle weight and 400 lbs (181 kg) to
the rear axle weight. The vehicle
now weighs:
Weight is still below 7,200 lbs
(3 266 kg) and you might think
700 additional pounds (318 kg)
should be subtracted from the
trailering capacity to stay within
GCWR limits. The maximum trailer
would only be 7,800 lbs (3 538 kg).
You may go further and think
the tongue weight should be limitedto less than 1,000 lbs (454 kg) to
avoid exceeding GVWR. But
the effect on the rear axle must still
be considered. Because the rear
axle now weighs 3,100 lbs
(1 406 kg), 900 lbs (408 kg) can be
put on the rear axle without
exceeding RGAWR. The effect of
tongue weight is about 1.5 times the
actual weight. Dividing the 900 lbs
(408 kg) by 1.5 leaves only
600 lbs (272 kg) of tongue weight
that can be handled. Since
tongue weight is usually at least
10 percent of total loaded trailer
weight, expect that the largest trailer
the vehicle can properly handle is
6,000 lbs (2 721 kg).
It is important that the vehicle
does not exceed any of its
ratings — GCWR, GVWR, RGAWR,
Maximum Trailer Rating or
Tongue Weight. The only way
to be sure it is not exceeding any of
these ratings is to weigh the vehicle
and trailer.
Driving Your Vehicle 4-47

Page 284 of 382

(C) Aspect Ratio:A two-digit
number that indicates the tire
height-to-width measurements.
For example, if the tire size
aspect ratio is 75, as shown
in item C of the light truck
(LT-Metric) tire illustration,
it would mean that the tire’s
sidewall is 75 percent as high
as it is wide.
(D) Construction Code
:A letter code is used to indicate
the type of ply construction in
the tire. The letter R means
radial ply construction; the
letter D means diagonal or
bias ply construction; and the
letter B means belted-bias
ply construction.
(E) Rim Diameter
:Diameter of
the wheel in inches.
(F) Service Description
:The service description indicates
the load range and speed
rating of a tire. The load index
can range from 1 to 279. Speed
ratings range from A to Z.
Tire Terminology and
Denitions
Air Pressure:The amount of
air inside the tire pressing
outward on each square inch
of the tire. Air pressure is
expressed in pounds per square
inch (psi) or kilopascal (kPa).
Accessory Weight
:This means
the combined weight of optional
accessories. Some examples
of optional accessories are,
automatic transmission, power
steering, power brakes, power
windows, power seats, and air
conditioning.
Aspect Ratio
:The relationship
of a tire’s height to its width.
Belt
:A rubber coated layer of
cords that is located between the
plies and the tread. Cords may
be made from steel or other
reinforcing materials.Bead
:The tire bead contains
steel wires wrapped by steel
cords that hold the tire onto
the rim.
Bias Ply Tire
:A pneumatic tire
in which the plies are laid at
alternate angles less than
90 degrees to the centerline
of the tread.
Cold Tire Pressure
:The
amount of air pressure in a tire,
measured in pounds per
square inch (psi) or kilopascals
(kPa) before a tire has built
up heat from driving. See
Inflation - Tire Pressure on
page 5-51.
Curb Weight
:The weight of a
motor vehicle with standard
and optional equipment including
the maximum capacity of fuel,
oil, and coolant, but without
passengers and cargo.
5-48 Service and Appearance Care

Page 285 of 382

DOT Markings:A code molded
into the sidewall of a tire
signifying that the tire is in
compliance with the U.S.
Department of Transportation
(DOT) motor vehicle safety
standards. The DOT code
includes the Tire Identication
Number (TIN), an alphanumeric
designator which can also
identify the tire manufacturer,
production plant, brand, and date
of production.
GVWR
:Gross Vehicle Weight
Rating. SeeLoading the Vehicle
on page 4-35.
GAWR FRT
:Gross Axle
Weight Rating for the front axle.
SeeLoading the Vehicle on
page 4-35.
GAWR RR
:Gross Axle
Weight Rating for the rear axle.
SeeLoading the Vehicle on
page 4-35.Intended Outboard Sidewall
:The side of an asymmetrical tire,
that must always face outward
when mounted on a vehicle.
Kilopascal (kPa)
:The metric
unit for air pressure.
Light Truck (LT-Metric) Tire
:A tire used on light duty trucks
and some multipurpose
passenger vehicles.
Load Index
:An assigned
number ranging from 1 to 279
that corresponds to the load
carrying capacity of a tire.
Maximum Ination Pressure
:The maximum air pressure
to which a cold tire can be
inated. The maximum air
pressure is molded onto the
sidewall.
Maximum Load Rating
:The load rating for a tire at the
maximum permissible ination
pressure for that tire.Maximum Loaded Vehicle
Weight
:The sum of curb
weight, accessory weight,
vehicle capacity weight, and
production options weight.
Normal Occupant Weight
:The number of occupants
a vehicle is designed to seat
multiplied by 150 lbs (68 kg).
SeeLoading the Vehicle
on page 4-35.
Occupant Distribution
:Designated seating positions.
Outward Facing Sidewall
:The side of an asymmetrical tire
that has a particular side that
faces outward when mounted on
a vehicle. The side of the tire
that contains a whitewall,
bears white lettering, or bears
manufacturer, brand, and/or
model name molding that
is higher or deeper than the
same moldings on the
other sidewall of the tire.
Service and Appearance Care 5-49

Page:   1-10 11-20 next >