HYUNDAI GX350 L 2005 Owners Manual

6
DO-IT-YOURSELF MAINTENANCE
21
HEADLIGHT AIMING ADJUSTMENT
!
!
G290A03L-AATHID Type (If Installed)Before performing aiming adjustment, make
sure of the following.
G290A02L-A
Vertical
aiming1. Keep all tires inflated to the correct pressure.
2. Place the vehicle on level ground and press
the front bumper & rear bumper down sev-
eral times. Place vehicle at a distance of 118
in. (3m) from the test wall.
3. See that the vehicle is unloaded (except for
full levels of coolant, engine oil and fuel, and
spare tire, jack, and tools). Have the driver
or equivalent weight placed in driver's seat.
4. Clean the head light lenses and turn on the
headlights (Low beam).
5. Open the hood.
6. Draw the vertical line (through the center of
each headlight) and the horizontal line
(through the center of each headlight) on the
aiming screen.
And then, draw a parallel line at 0.8in.(21mm.)
under the horizontal line.
7. Adjust each cut-off line of the low beam to the
parallel line with a phillips screwdriver -
VERTICAL AIMING
WARNING:
If you need headlight aiming adjustment,
have your vehicle inspected by your Hyundai
Dealer.
Don't attempt to replace or inspect the HID
headlight bulb to prevent danger of an
electric shock.General Type
WARNING:
Horizontal aiming should be adjusted by an
authorized Hyundai Dealer.
G290B02L-AATAdjustment After Headlight Assembly
ReplacementIf the vehicle has had front body repair and the
headlight assembly has been replaced, the
headlight aiming should be checked using an
aiming screen as shown in the illustration. Turn
on the headlight switch. (Low Beam Position)
1. Adjust headlights so that main axis of light is
parallel to center line of the body and is
aligned with point "P" shown in the illustration.
2. Dotted lines in the illustration show center of
headlights.
G290B01L-A
LW
H
HCut-off line
Ground
line
"P" Horizontal lineVertical line
0.83 in. (21 mm)
xgflhma-6.p656/16/04, 2:59 PM 21
ProCarManuals.com

6
DO-IT-YOURSELF MAINTENANCE
22
Replacement instructions:
1. Allow the bulb to cool. Wear eye protection.
2. Open the engine hood.
3. Always grasp the bulb by its plastic base,
avoid touching the glass.
G260A01L-GATREPLACEMENT OF LIGHT BULBSBefore attempting to replace a light bulb, be sure
the switch is turned to the "OFF" position.
The next paragraph shows how to reach the
light bulbs so they may be changed. Be sure to
replace the burned-out bulb with one of the
same number and wattage rating.
See page 6-31 for the wattage descriptions.
G270A03L G270A02L-AAT
HEADLIGHT AND FRONT TURN SIG-
NAL LIGHT
High beam
Low beam
Turn signal light
!
CAUTION:
o Keep the lights out of contact with pe-
troleum products, such as oil, gasoline,
etc.
o Be sure to replace the LED type equipped
bulbs with an assembly. SPECIFICATIONS:
"H";
Horizontal center line of headlights from
ground:
General type : 24.96 in. (634 mm)
HID type : 24.72 in. (628 mm)
"W";
Distance between each headlight center:
48.8 in. (1,240 mm)
"L";
Distance between the headlights and the
wall that the lights are tested against:
118 in. (3,000 mm)
xgflhma-6.p656/16/04, 2:59 PM 22
ProCarManuals.com

6
DO-IT-YOURSELF MAINTENANCE
23
G270A04L
General type
High beam (H1)Low beam (H7)
Turn signal light
6. Turn the plastic cover counterclockwise
and remove it.
G270A06L
7. Disconnect the power cord from the bulb
base in the back of the headlight.
G270D01L
4. Using a socket wrench of the correct size,
remove the headlight assembly mounting
bolts.
G270D02L
5. Disconnect the power cord from the back of
the headlight.
xgflhma-6.p656/16/04, 2:59 PM 23
ProCarManuals.com

6
DO-IT-YOURSELF MAINTENANCE
24
!
G270A08L
12.To replace the front turn signal light bulb, take
out it from the bulb holder and install the new
bulb.
1FJB5036
WARNING:
This halogen bulb contains gas under pres-
sure and if impacted could shatter, result-
ing in flying fragments. Always wear eye
protection when servicing the bulb. Protect
the bulb against abrasions or scratches
and against liquids when lighted. Turn the
bulb on only when installing in a headlight.
Replace the headlight if damaged or cracked.
Keep the bulb out of the reach of children
and dispose of the used bulb with care.
G270A07L
8. Push the bulb spring to remove the headlight
bulb.
9. Remove the protective cap from the re-
placement bulb and install the new bulb by
matching the plastic base with the headlight
hole. Retighten the bulb spring and recon-
nect the power cord.
10.Use the protective cap and carton to prompt-
ly dispose of the old bulb.
11.Check for proper headlight aim.
xgflhma-6.p656/16/04, 2:59 PM 24
ProCarManuals.com

6
DO-IT-YOURSELF MAINTENANCE
25
G270I01L-GATFRONT FOG LIGHT
G270D01L
1. Remove the headlight assembly mounting
bolts.
G270D02L
2. Disconnect the power cord from the bulb
base in the back of the headlight.
G270D03L
3. Take out front fog light from the bulb holder
by turning it counterclockwise.
xgflhma-6.p656/16/04, 2:59 PM 25
ProCarManuals.com

6
DO-IT-YOURSELF MAINTENANCE
26
3. To replace the rear combination light (stop/
tail light and rear turn signal light), remove it
from the bulb holder and install the new bulb. Stop/
Tail light
G270B02L
Rear turn
signal light
G270D04L
4. Disconnect the power cord from the bulb.
5. Replace with a new bulb.
G270B01L G270D01L-GAT
REAR COMBINATION LIGHT
(Stop /Tail Light and Rear Turn Signal
Light)1. Open the trunk lid.
2. Remove the cover on the inside of rear
luggage trim by unscrewing the screws.
xgflhma-6.p656/16/04, 2:59 PM 26
ProCarManuals.com

6
DO-IT-YOURSELF MAINTENANCE
27
G270C01L-GATLUGGAGE COMPARTMENT LIGHT1. Open the trunk lid.
2. Remove the luggage compartment light cover
on the rear package tray panel with a blade
screwdriver.
G270E01L
Screwdriver
2. To replace the back-up light, remove it from
the bulb holder and install the new bulb.
G270C01L G270J01L-GAT
BACK UP LIGHT1. Remove the trunk lid trim.
Back-up light
G270E02L
3. Disconnect the connector.
xgflhma-6.p656/16/04, 2:59 PM 27
ProCarManuals.com

6
DO-IT-YOURSELF MAINTENANCE
28
HTB284
4. Replace with a new bulb.
2. Disconnect the connector.
G270F01L G270E01L-AAT
SIDE MARKER LIGHT1. Remove the side marker light cover with a
blade screwdriver.
G270I01L
Screwdriver
xgflhma-6.p656/16/04, 2:59 PM 28
ProCarManuals.com

6
DO-IT-YOURSELF MAINTENANCE
29
HTB278
3. Replace with a new bulb.
G270G01E-GATINTERIOR LIGHT
G270G01L
1. Remove the plastic cover with a flat blade
screwdriver.
Screwdriver
2. Replace with a new bulb.
G270G02L
xgflhma-6.p656/16/04, 2:59 PM 29
ProCarManuals.com

6
DO-IT-YOURSELF MAINTENANCE
30
G270E02L
HTB284
G270K01L-GATGLOVE BOX ILLUMINATED LIGHT1. Open the glove box.
2. Remove the glove box illuminated light cover
with a blade screwdriver.
G270H01L
Screwdriver3. Disconnect the connector.
4. Replace with a new bulb.
xgflhma-6.p656/16/04, 2:59 PM 30
ProCarManuals.com