key INFINITI FX35 2004 User Guide

ATC-60
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
AUXILIARY MECHANISM: FOOT POSITION SETTING TRIMMER
Wind distribution ratio in FOOT mode can be set.
Operating procedures for this trimmer are as follows:
1. Begin Self-diagnosis STEP-5 mode. Refer to AT C - 5 3 , "
Self-diagnosis Function" .
2. Press (fan) UP switch to set system in auxiliary mode.
3. Display shows 61 in auxiliary mechanism. It takes approximately 3 seconds.
4. Press the mode switch as desired.
AUXILIARY MECHANISM: INLET PORT MEMORY FUNCTION
When ignition key is turned from OFF to ON, inlet port can be set to AUTO or manual.
Operating procedures for this trimmer are as follows:
1. Begin Self-diagnosis STEP-5 mode. Refer to AT C - 5 3 , "
Self-diagnosis Function" .
2. Press (fan) UP switch to set system in auxiliary mode.
3. Display shows 61 in auxiliary mechanism. It takes approximately 3 seconds.
4. Press the recirculation (REC) and fresh (FRE) switch as desired.
RJIA1971E
SwitchLED status of
REC/FRE
switchSetting status Setting changeover method
RECON Manual REC status is memorized. (Initial setting)
REC SW: ON
OFF AUTO control
FREON Manual FRE status is memorized.
FRE SW: ON
OFF AUTO control (Initial setting)

AV-58
INTEGRATED DISPLAY SYSTEM
Revision: 2004 November 2004 FX35/FX45
SETTING SCREEN

Setting of electric status can be changed by A/C and AV switch. The signal is sent to BCM through display
unit to change vehicle electric system setting.

Display unit is communicating with driver seat control unit.

Pressing “SETTING” switch once cycles display from DISPLAY→LANGUAGE→BEEP SET→SERVICE
ALERT→PERSONALIZED SETTINGS MENU→DISPLAY OFF→DISPLAY.

Using the joystick, setting of each item will become possible.
Adjustable Vehicle Status
NOTE:
Setting in factory shipment is ON.
Setting itemsSetting varia-
tionsInitial
settingOperation
DISPLAY ON/OFF ON It switches displayed/Non-displayed of the screen.
LANGUAGEENGLISH/
FRANCAIS– It switches displayed language.
BEEP SET ON/OFF ONIt selects beep sound ON/OFF during switch operation. How-
ever, even if beep is set OFF, beep for NO OPERATION and
for screen interception are not reset.
SERVICE ALERT ON/OFF OFFIt switches displayed/Non-displayed of alert indication.

When the setting is ON, if engine oil or tire rotation will be
replace distance, alert is displayed.

When the setting is OFF, alert is not displayed.
PERSONALIZED
SETTING MENUSLIDE BACK DR
SEAT ON EXITON/OFF
ON
NoteThe driver’s seat automatically moves back and returns to
the original position for exceptional ease of exit and entry.
(Models with automatic drive positioner.)
LIFT STEERING
WHEEL ON EXITON/OFF
ON
NoteThe steering column automatically tilts up and returns to the
original position for exceptional ease of entry and exit. (Mod-
els with automatic drive positioner.)
REMOTE UNLOCK
DOOR LOGICDR-1ST/ALL DR-1STThis key can switch the unlock doors of the 1st unlocking
operation as follows:

Only the driver side door⇔All the doors
HORN CHIRP WITH
REMOTEON/OFF ONThis key changes the horn chirp mode occurring when press-
ing the LOCK button on the keyfob.
LAMPS FLASH
WITH REMOTEALL/LOCK/
UNLOCK/OFFALLThis key changes the hazard indicator flash mode occurring
when pressing the LOCK or UNLOCK button on the keyfob.
AUTO RE-LOCK
TIME5m/1m/OFF 1mThe length of auto door re-lock time can be set. Select the
“Auto Re-Lock timer” key, then move the joystick to adjust the
time.
AUTO HEADLAMP
SENSITIVITYLEVEL 1/2/3/4LEVEL
2Automatic light illumination can be set as desired. Select the
“Auto Headlamp Sensitivity” key, then move the joystick to
the left (lower) or right (higher).
AUTO HEADLAMP
OFF DELAYOFF/30/45/60/
90/120/150/
180 SEC45 SECThis key can control how long it takes the automatic turn off
timer to extinguish the headlamps in “AUTO” position. Select
the “Auto Headlamp Off Delay” key, then move the joystick to
the left or right to adjust the timer.
SPEED SENSING
WIPER INTERVALON/OFF ONThis key turns on and off the driving speed dependent inter-
mittent wiper function.
CONFIRM RESET
SETTINGSYES/NO NOWhen this key is selected and turned on using the “ENTER”
button, all settings mode by PERSONALIZED SETTINGS will
return to the initial conditions.

NAVIGATION SYSTEM
AV-95
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
Vehicle Electronic Systems
How To Perform Vehicle Electronic Systems
1. Start the engine.
2. Push “SETTING” button.
3. Select “Vehicle Electronic Systems”.
4. Push “Enter” switch.
Application Items
Adjust Driver Seat When Exiting Vehicle
1. Select “Adjust Driver Seat When Exiting Vehicle”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Lift Steering Column When Exiting Vehicle
1. Select “Lift Steering Column When Exiting Vehicle”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
SKIA5987E
Icon DescriptionReference
page
Adjust Driver Seat When Exiting Vehicle The driver's seat automatically moves back and returns to the original
position.AV- 9 5
Lift Steering Column When Exiting Vehicle This function can be performed to On or Off.AV- 9 5
Selective Door UnlockThis key can switch the unlock doors of the 1st unlocking operation as
follows.

Only the driver side door (On)⇔All the doors (Off)AV- 9 6
Keyless Remote Response-HornThis key changes the horn chirp mode occurring when pressing the
Lock button on the Intelligent Key or keyfob. AV- 9 6
Keyless Remote Response-LightsThis key changes the hazard indicator flash mode occurring when
pressing the Lock or Unlock button on the Intelligent Key or keyfob. AV- 9 6
Auto Re-Lock TimeThe length of auto door relock time can be set.
(Setting value: OFF, 1min or 5min)AV- 9 6
Sensitivity of Automatic Headlights Sensitivity of automatic light can be set as desired.AV- 9 6
Automatic Headlights Off DelayYou can control how long it takes the automatic turn off timer to extin-
guish the headlights in AUTO position.
(Setting value: OFF, 30sec, 45sec, 60sec, 90sec, 120sec, 150sec or
180sec)AV- 9 6
Speed Dependent wiper This function can be performed to On or Off.AV- 9 6
Intelligent Key Lock Response-SoundThe sound pattern of the Intelligent Key operation can be set as
desired. (Setting value:OFF, Beeper or Horn chirp)AV- 9 6
Intelligent Key Unlock Response-Beep SoundThe beep sound when unlocking door with the intelligent key operation
can be turned On or Off.AV- 9 6
Intelligent Key Engine Start Function This function can be performed to On or Off.AV- 9 6
Intelligent Key Lock/Unlock FunctionThe door handle request switch lock/unlock operation with the Intelli-
gent Key can be canceled or activated.AV- 9 6
Return All Settings to DefaultThe all settings made by VEHICLE ELECTRONICS will return to
default.AV- 9 6

AV-96
NAVIGATION SYSTEM
Revision: 2004 November 2004 FX35/FX45
Selective Door Unlock (With Intelligent Key)
1. Select “Selective Door Unlock”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Keyless Remote Response -Horn
1. Select “Keyless Remote Response-Horn”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Keyless Remote Response -Lights
1. Select “Keyless Remote Response-Light”.
2. Push “Enter” switch.
Auto Re-Lock Time
1. Select “Auto Re-Lock Time”.
2. Move the joystick and push “Enter” switch to adjust the time.
Sensitivity of Automatic Headlights
1. Select “Sensitivity of Automatic Headlights”.
2. Move the joystick to left (lower) or right (higher) and push “Enter” switch.
Automatic Headlights Off Delay
1. Select “Automatic Headlights Off Delay”.
2. Move the joystick left or right to adjust the timer and push “Enter” switch.
Speed Dependent Wiper
1. Select “Speed Dependent Wiper”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Intelligent Key Lock Response-Sound
1. Select “Intelligent Key Lock Response-Sound”.
2. Push “Enter” switch to change the sound pattern.
Intelligent Key Unlock Response-Beep Sound
1. Select “Intelligent Key Unlock Response-Sound”.
2. Push “Enter” switch to change the sound pattern.
Intelligent Key Engine Start Function
1. Select “Intelligent Key Engine Start Function”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Intelligent Key Lock/Unlock Function
1. Select “Intelligent Key Lock/Unlock”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Return All Settings to Default
1. Select “Return All Settings to Default”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.

NAVIGATION SYSTEM
AV-99
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
“HEADING” MODE

To display north heading, select “North up”.

To display the actual driving direction of the vehicle, select
“Heading up”.
“NEARBY DISPLAY ICONS” MODE

Select an icon to display on the map screen.
“SAVE CURRENT LOCATION” MODE

The current vehicle location can be registered in “Address
Book”.
NOTE:
“Address Book” can store 50 items max.
“ADJUST CURRENT LOCATION” MODE
1. Select an icon “right” or “left” to calibrate the heading direction.
(Arrow marks will rotate corresponding to the calibration key.)
SKIA0561E
SKIA0562E
SKIA0556E
SKIA0563E

BCS-1
BODY CONTROL SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION BCS
A
B
BCS
Revision: 2004 November 2004 FX35/FX45
BODY CONTROL SYSTEM
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
BCM (BODY CONTROL MODULE) ........................... 3
System Description .................................................. 3
BCM FUNCTION ................................................... 3
COMBINATION SWITCH READING FUNCTION ..... 3
CAN COMMUNICATION CONTROL .................... 5
BCM STATUS CONTROL ..................................... 6
SYSTEMS CONTROLLED BY BCM DIRECTLY ..... 7
SYSTEMS CONTROLLED BY BCM AND IPDM
E/R ........................................................................ 7
SYSTEMS CONTROLLED BY BCM AND COM-
BINATION METER ................................................ 7SYSTEMS CONTROLLED BY BCM AND INTEL-
LIGENT KEY UNIT ................................................ 7
MAJOR COMPONENTS AND CONTROL SYS-
TEM ....................................................................... 8
CAN Communication Unit ......................................... 9
Schematic ............................................................... 10
CONSULT-II ............................................................ 12
CONSULT–II INSPECTION PROCEDURE ......... 12
ITEMS OF EACH PART ...................................... 13
WORK SUPPORT ............................................... 14
CAN Communication Inspection Using CONSULT-
II (Self-Diagnosis) ................................................... 14
Removal and Installation of BCM ........................... 15
REMOVAL ........................................................... 15
INSTALLATION ................................................... 15

BCS-6
BCM (BODY CONTROL MODULE)
Revision: 2004 November 2004 FX35/FX45
BCM STATUS CONTROL
BCM changes its status depending on the operation status in order to save power consumption.
1. CAN communication status

With ignition switch ON, CAN communicates with other control units normally.

Control by BCM is being operated properly.

When ignition switch is OFF, switching to sleep mode is possible.

Even when ignition switch is OFF, if CAN communication with IPDM E/R and combination meter is
active, CAN communication status is active.
2. Sleep transient status

This status shuts down CAN communication when ignition switch is turned OFF.

It transmits sleep request signal to IPDM E/R and combination meter.

Two seconds after CAN communication of all control units stops, CAN communication switches to inac-
tive status.
3. CAN communication inactive status

With ignition switch OFF, CAN communication is not active.

With ignition switch OFF, control performed only by BCM is active.

Three seconds after CAN communication of all control units stops, CAN communication switches to
inactive status.
4. Sleep status

BCM is activated with low current consumption mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state.
–Key switch
–Hazard switch
–Door lock/unlock switch
–Front door switch (driver side, passenger side)
–Rear door switch (LH, RH)
–Back door opener switch
–Combination switch (passing, lighting switch 1st position, Front fog lamp)
–Key fob (lock/unlock signal)
–Key cylinder switch

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.

BCM (BODY CONTROL MODULE)
BCS-7
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: 2004 November 2004 FX35/FX45
SYSTEMS CONTROLLED BY BCM DIRECTLY
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT
System Reference
Power door lockBL-22, "
POWER DOOR LOCK SYSTEM"
Remote keyless entryBL-56, "REMOTE KEYLESS ENTRY SYSTEM"
Power window NOTEGW-15, "POWER WINDOW SYSTEM"
Sunroof NOTERF-10, "SUNROOF"
Room lamp timerLT-157, "INTERIOR ROOM LAMP"
Warning chimeDI-55, "WARNING CHIME"
Rear wiperWW-35, "REAR WIPER AND WASHER SYSTEM"
System Reference
Panic alarmBL-56, "
REMOTE KEYLESS ENTRY SYSTEM"
Theft warningBL-181, "VEHICLE SECURITY (THEFT WARNING) SYSTEM"
IVIS (NATS)BL-206, "IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)"
Headlamp, tail lamp, auto light system, battery saver control

LT- 7 , "HEADLAMP - XENON TYPE -"

LT-38, "DAYTIME LIGHT SYSTEM"

LT-54, "AUTO LIGHT SYSTEM"
Fog lampLT-77, "FRONT FOG LAMP"
Front wiperWW-4, "FRONT WIPER AND WASHER SYSTEM"
Rear window defoggerGW-86, "REAR WINDOW DEFOGGER"
System Reference
Warning chimeDI-55, "
WARNING CHIME"
Turn signal and hazard warning lampsLT-89, "TURN SIGNAL AND HAZARD WARNING LAMPS"
System Reference
Intelligent KeyBL-84, "
INTELLIGENT KEY SYSTEM"

BCS-8
BCM (BODY CONTROL MODULE)
Revision: 2004 November 2004 FX35/FX45
MAJOR COMPONENTS AND CONTROL SYSTEM
System Input Output
Remote control entry system key fob

All-door locking actuator

Turn signal lamp (LH, RH)
Power door lock system

Power window main switch
(door lock and unlock switch)

Power window sub switch (passenger side)
(door lock and unlock switch)All-door locking actuator
Power supply (IGN) to power window, sunroof Ignition power supply Power window and sunroof system
Power supply (BAT) to power window, sunroof
and power seatBattery power supplyPower window, sunroof system and
power seat
Panic alarm

Key switch

Key fobIPDM E/R
Theft warning system

All-door switch

Hood switch

Key fob

Power window main switch (door lock and
unlock switch)

IPDM E/R

Security indicator lamp
Auto light system

Optical sensor

Combination switchIPDM E/R
Battery saver control

Ignition switch

Combination switchIPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch

Turn signal lamp

Combination meter
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
Room lamp timer

Key switch

key fob

Power window main switch (door lock and
unlock switch)

Front door switch driver side

All-door switchInterior room lamp
Key warning chime

Key switch

Front door switch driver sideCombination meter
(warning buzzer)
Light warning chime

Combination switch

Front door switch driver sideCombination meter
(warning buzzer)
Seat belt warning chime

Combination meter (Seat belt buckle
(driver side) switch)

Ignition switchCombination meter
(warning buzzer)
Vehicle-speed-sensing intermittent wiper

Combination switch

Combination meterIPDM E/R
Rear intermittent wiper Combination switch Rear wiper motor
Rear window defogger

Rear window defogger switch

Ignition switchIPDM E/R
A/C switch signal Unified meter and A/C amp. ECM
Blower fan switch signal Unified meter and A/C amp. ECM

BCM (BODY CONTROL MODULE)
BCS-13
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: 2004 November 2004 FX35/FX45
4. Select the desired part to be diagnosed on the “SELECT TEST
ITEM” screen.
ITEMS OF EACH PART
NOTE:
CONSULT-II will Only display systems the vehicle possesses.
×:Applicable
NOTE:
This item is indicated, but it is what it does not use.
SKIA4963E
System and item CONSULT-II displayDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−
DIAG
RESULTSDATA
MONI-
TORCAN
DIAG
SUP-
PORT
MNTRECU
PA R T
NUM-
BERACTIVE
TESTCON-
FIGU-
RATION
Power door lock system DOOR LOCK×× ×
Rear window defogger REAR DEFOGGER××
Warning chime BUZZER××
Room lamp timer INT LAMP×× ×
Remotecontrol entry system MULTI REMOTE ENT×× ×
Headlamp HEAD LAMP×× ×
Wiper WIPER××
Turn signal lamp
Hazard lampFLASHER××
Blower fan switch signal
A/C switch signalAIR CONDITONER×
Intelligent Key system INTELLIGENT KEY×
Combination switch COMB SW×
BCM BCM× × ×××
×
Note
IVIS IMMU××
Room lamp battery saver BATTERY SAVER×× ×
Trunk lid
NoteTRUNK××
Vehicle security system THEFT ALM×× ×
Retained power control RETAINED PWR×× ×
Oil pressure switch SIGNAL BUFFER××