brake sensor INFINITI FX35 2004 Manual Online

TROUBLE DIAGNOSIS
BRC-31
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2004 November 2004 FX35/FX45
CAUTION:
When “START (NISSAN BASED VHCL)” is touched immediately after starting engine or turning on
ignition switch, “ABS” might not be displayed in the system selection screen. In this case, repeat
the operation from step 1.
4. Return to the Monitor Item Selection screen, and touch “ECU INPUT SIGNALS”, “MAIN SIGNALS” or
“SELECTION FROM MENU”. Refer to the following information.
5. When “START” is touched, the data monitor screen is displayed.
Display Item List
Item
(Unit)Data monitor item selection
Remarks
ECU INPUT
SIGNALSMAIN
SIGNALSSELECTION
FROM MENU
GEAR×××Gear position judged by PNP
switch signal is displayed.
FR RH SENSOR
(km/h, MPH)×××Wheel speed calculated by front
RH wheel sensor signal is dis-
played.
FR LH SENSOR
(km/h, MPH)×××Wheel speed calculated by front
LH wheel sensor signal is dis-
played.
RR RH SENSOR
(km/h, MPH)×××Wheel speed calculated by rear
RH wheel sensor signal is dis-
played.
RR LH SENSOR
(km/h, MPH)×××Wheel speed calculated by rear
LH wheel sensor signal is dis-
played.
BATTERY VOLT
(V)×××Voltage supplied to ABS actuator
and electric unit (control unit) is
displayed.
SLCT LVR POSI×××Shift position judged by PNP
switch signal.
ACCEL POS SIG
(%)×––Throttle valve open/close status
judged by CAN communication
signal is displayed.
ENGINE SPEED
(rpm)×××Engine speed judged by CAN
communication signal is displayed.
STR ANGLE SIG
(deg)×––Steering angle detected by steer-
ing angle sensor is displayed.
YAW RATE SEN
(d/s)××–Yaw rate detected by yaw rate
sensor is displayed.
DECEL G-SEN (AWD model)
(G)×××Longitudinal acceleration detected
by decel G-sensor is displayed.
SIDE G-SENSOR
(m/s
2 )×––Lateral acceleration detected by
side G-sensor is displayed.
PRESS SENSOR
(bar)×––Brake fluid pressure detected by
pressure sensor is displayed.
STOP LAMP SW
(ON/OFF)×××Stop lamp switch (ON/OFF) status
is displayed.
OFF SW
(ON/OFF) ×× ×VDC OFF switch (ON/OFF) sta-
tus is displayed.
ABS WARN LAMP
(ON/OFF)–××ABS warning lamp (ON/OFF) sta-
tus is displayed.
SLIP LAMP
(ON/OFF)–××SLIP indicator lamp (ON/OFF) sta-
tus is displayed.
FR LH IN SOL
(ON/OFF)–××Front LH IN ABS solenoid (ON/
OFF) status is displayed.

TROUBLE DIAGNOSIS
BRC-35
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2004 November 2004 FX35/FX45
For Fast and Accurate DiagnosisAFS001SR
PRECAUTIONS FOR DIAGNOSIS

Before performing diagnosis, always read precautions. Refer to BRC-12, "How to Proceed With Diagno-
sis" .

If ABS actuator and electric unit (control unit), steering angle sensor, steering system parts or suspension
system parts have been replaced, or if alignment has been adjusted, be sure to adjust neutral position of
steering angle sensor before driving. Refer to BRC-6, "
Adjustment of Steering Angle Sensor Neutral Posi-
tion" .

After diagnosis is finished, be sure to erase memory. Refer to BRC-27, "SELF-DIAGNOSIS" .

When checking continuity and voltage between units, be sure to check for disconnection, looseness,
bend, or collapse of connector terminals. If any malfunction is found, repair or replace connector termi-
nals.

For intermittent symptoms, possible cause is malfunction in harness, harness connector, or terminals.
Move harness, harness connector, and terminals to check for poor connections.

If a circuit tester is used for the check, be careful not to forcibly extend any connector terminal.

To use CONSULT-II to perform self-diagnosis of ABS actuator and electric unit (control unit), active tests,
or work support, first stop work, then connect CONSULT-II and select “ABS”.

While self-diagnostic results of CONSULT-II shows malfunction, if CONSULT-II active test is performed,
an engine system error may be indicated. In this case, start engine to resume the normal screen.

VDC/TCS/ABS system electronically controls brake operation and engine output. The following symptoms
may be caused by normal operations:
Symptom Symptom description Result
Motor operation noiseThis is noise of motor inside ABS actuator and electric unit (control unit).
Slight noise may occur during VDC, TCS, and ABS operation.
Normal
When the vehicle speed goes over 20 km/h (12.5 MPH), motor and
valves operating noise may be heard. It happens only once after IGN
(ignition) is ON. This is a normal status of the system operation check.
System operation check
noiseWhen engine starts, slight “click” noise may be heard from engine room.
This is normal and is part of system operation check.Normal
VDC/TCS operation
(SLIP indicator lamp blink-
ing)TCS may activate momentarily if wheel speed changes when driving
over location where friction coefficient varies, when up/downshifting, or
when fully depressing accelerator pedal.
Normal
Cancel the VDC/TCS
function for the
inspection on a chas-
sis dynamometer. For inspection of speedometer or other instruments, press
VDC OFF SW to turn VDC/TCS function off.
When accelerator pedal is depressed on a chassis dynamometer (fixed
front-wheel type), vehicle speed will not increase. This is not normal. It is
result of TCS being activated by stationary front wheels. Warning lamp
may also illuminate to indicate “sensor system error”. This is also nor-
mal, and is the result of the stationary front wheels being detected. To be
certain, restart engine, and drive vehicle at 30 km/h (19 MPH) or more.
Make sure warning lamp does not illuminate.
ABS operation (Longer stop-
ping distance)On roads with low friction coefficients, such as snowy roads or gravel
roads, vehicles with ABS may require a longer stopping distance. There-
fore, when driving on such roads, avoid overconfidence and keep speed
sufficiently low.Normal
Insufficient feeling of accel-
erationDepending on road conditions, driver may feel that feeling of accelera-
tion is insufficient. This is because traction control, which controls
engine and brakes to achieve optimal traction, has the highest priority
(for safety). As a result, there may be times when acceleration is slightly
less than usual for the same accelerator pedal operation.Normal

TROUBLE DIAGNOSIS
BRC-37
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2004 November 2004 FX35/FX45
BASIC INSPECTION 3: ABS WARNING LAMP, VDC OFF INDICATOR LAMP, SLIP INDICATOR
LAMP AND BRAKE WARNING LAMP INSPECTION
1. Make sure ABS warning lamp, VDC OFF indicator lamp (when VDC OFF switch is OFF), and SLIP indica-
tor lamp turns on approximately 2 second, and brake warning lamp turns on when ignition switch is turned
ON. If they do not, check VDC OFF indicator lamp and then VDC OFF switch. Refer to BRC-53, "
VDC
OFF SWITCH" . Check CAN communications. Refer to “CAN Communication Inspection”. If there are no
errors with VDC OFF switch and CAN communication system, check combination meter. Refer to DI-4,
"COMBINATION METERS" .
2. Make sure ABS warning lamp, VDC OFF indicator lamp, SLIP indicator lamp turn off approximately 2 sec-
ond after turn ignition switch ON, and brake warning lamp turns off after engine starts. If lamps do not turn
off, perform self-diagnosis.
3. With engine running, make sure VDC OFF indicator lamp turns on and off when VDC OFF switch is
turned ON and OFF. If indicator lamp status does not correspond to switch operation, check the VDC OFF
switch system. Refer to BRC-53, "
VDC OFF SWITCH" .
4. Make sure ABS warning lamp, VDC OFF indicator lamp, and SLIP indicator lamp turn off 2 seconds after
engine is started. If ABS warning lamp, VDC OFF indicator lamp, and SLIP indicator lamp have not turned
off 10 seconds after engine has been started, perform self-diagnosis of ABS actuator and electric unit
(control unit).
5. After performing the self-diagnosis, be sure to erase the error memory. Refer to BRC-27, "
SELF-DIAGNO-
SIS" .
CAUTION:
Brake warning lamp turns on when parking brake is operated (switch on) and brake fluid level
switch is activated (leak of brake fluid).
Inspection 1: Wheel Sensor SystemAFS001ST
DTC C1101-C1108
After using the CONSULT-II SELF-DIAG RESULTS to determine the location of the malfunctioning wheel sen-
sor, check all areas to determine the component to be replaced.
CAUTION:

Do not measure the resistance value and also voltage between sensor terminal with tester etc.,
because sensor is an active sensor.

Do not expand terminal of connector with a tester terminal stick, when it does the inspection with
tester.
INSPECTION PROCEDURE
1. CHECK TIRE
Check air pressure, wear and size.
Are air pressure, wear, and size within the standard values?
YES >> GO TO 2.
NO >> Adjust air pressure, or replace tire.
2. CHECK SENSOR AND SENSOR ROTOR

Check the condition of the sensor mount (for looseness, etc.).

Check the surface of front sensor rotor rubber for damage.

Check rear sensor rotor for damage.
OK or NG
OK >> GO TO 3.
NG >> Repair sensor mount or replace sensor rotor.

TROUBLE DIAGNOSIS
BRC-41
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2004 November 2004 FX35/FX45
2. CHECK CONNECTOR
1. Disconnect pressure sensor connector and ABS actuator and electric unit (control unit) connector, check
terminals for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminal.
2. Reconnect connectors and Re-perform ABS actuator and electric unit (control unit) self-diagnosis.
OK or NG
OK >> Connector terminal contact is loose, damaged, open or shorted.
NG >> GO TO 3.
3. CHECK PRESSURE SENSOR HARNESS
1. Turn ignition switch OFF and disconnect pressure sensor con-
nector and ABS actuator and electric unit (control unit) connec-
tor.
2. Check continuity between ABS actuator and electric unit (control
unit) harness connector E56 and pressure sensor harness con-
nector E53.
OK or NG
OK >> GO TO 4.
NG >> If the open or short in harness, repair or replace harness.
4. PRESSURE SENSOR INSPECTION
1. Connect pressure sensor connector and ABS actuator and electric unit (control unit) connector.
2. Use CONSULT-II “Data Monitor” to check pressure sensor value.
OK or NG
OK >> INSPECTION END
NG >> Pressure sensor is damaged or malfunctioning, replace pressure sensor.
SFIA1188E
ABS actuator and electric
unit (control unit)
(Harness connector E56)Pressure sensor
(Harness connector E53)Continuity
19 (L) 1 (L) Yes
20 (Y) 2 (Y) Yes
18 (W) 3 (W) Yes
Condition Data monitor display
When brake pedal is depressed. Positive value
When brake pedal is released. Approx. 0 bar

DI-28
UNIFIED METER AND A/C AMP
Revision: 2004 November 2004 FX35/FX45
UNIFIED METER AND A/C AMPPFP:27760
System DescriptionAKS005N8

For the unified meter and A/C amp., the signal required for controlling the combination meter are inte-
grated in the A/C auto amp.

Unified meter and A/C amp. controls each operation for A/C auto amp. For information regarding A/C con-
trol, refer to AT C - 3 0 , "
AIR CONDITIONER CONTROL" in ATC section.

Unified meter and A/C amp. inputs necessary information for combination meter from each unit by CAN
communication and so on.

And unified meter and A/C amp. outputs these signals using communication line (TX, RX) between unified
meter and A/C amp. and combination meter.

The signals required for the distance to empty (DTE) display are centralized in the unified meter and A/C
amp., converted into data, and sent to the display unit (without NAVI) display control unit (with NAVI) using
CAN communication.

Other input signals are also sent to the ECM, TCM, AWD control unit, BCM, display unit (without NAVI)
and display control unit (with NAVI) using CAN communication.

The unified meter and A/C amp. have a CONSULT-II function (self-diagnostic results, CAN diagnostic
support monitor, data monitor).
INPUT/OUTPUT SIGNALS
Between Unified Meter & A/C amp. and Combination Meter
Unit Input Output
Unified meter and A/C amp.

Seat belt buckle switch signal (Driver's side)

Parking brake signal

Illumination control nighttime required signal

Refuel status signal

Low-fuel warning lamp condition signal

Combination meter receive error signal

Delivery destination data signal

Combination meter specifications signal

Vehicle speed signal (8-pulse)

Engine speed signal

Engine coolant temperature signal

Fuel level sensor signal (resistance value)

Malfunction indicator lamp signal

ABS warning lamp signal

Low tire pressure warning lamp signal

Brake warning lamp signal

A/T CHECK warning lamp signal

ICC warning lamp signal

Oil pressure switch signal

Door switch signal

AWD warning lamp signal

VDC OFF indicator lamp signal

SLIP indicator lamp signal

ASCD CRUISE indicator lamp signal

ASCD SET indicator lamp signal

High beam request signal

Turn indicator signal

Snow mode switch signal

ICC system display signal

A/T position indicator signal

Manual mode indicator signal

Manual mode gear position signal

CAN communication condition signal of A/T

Position lights request signal

Buzzer output signal

EC-6Revision: 2004 November 2004 FX35/FX45 DTC P1444 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE ...............................494
Description ............................................................494
CONSULT-II Reference Value in Data Monitor Mode
.494
On Board Diagnosis Logic ....................................495
DTC Confirmation Procedure ...............................495
Wiring Diagram .....................................................496
Diagnostic Procedure ...........................................498
Component Inspection ..........................................501
Removal and Installation ......................................501
DTC P1446 EVAP CANISTER VENT CONTROL
VALVE .....................................................................502
Component Description ........................................502
CONSULT-II Reference Value in Data Monitor Mode
.502
On Board Diagnosis Logic ....................................502
DTC Confirmation Procedure ...............................503
Wiring Diagram .....................................................504
Diagnostic Procedure ...........................................505
Component Inspection ..........................................506
DTC P1564 ICC STEERING SWITCH ....................508
Component Description ........................................508
CONSULT-II Reference Value in Data Monitor Mode
.508
On Board Diagnosis Logic ....................................508
DTC Confirmation Procedure ...............................508
Wiring Diagram .....................................................510
Diagnostic Procedure ...........................................511
Component Inspection ..........................................514
DTC P1564 ASCD STEERING SWITCH ................515
Component Description ........................................515
CONSULT-II Reference Value in Data Monitor Mode
.515
On Board Diagnosis Logic ....................................515
DTC Confirmation Procedure ...............................516
Wiring Diagram .....................................................517
Diagnostic Procedure ...........................................518
Component Inspection ..........................................520
DTC P1568 ICC FUNCTION ...................................521
On Board Diagnosis Logic ....................................521
DTC Confirmation Procedure ...............................521
Diagnostic Procedure ...........................................521
DTC P1572 ICC BRAKE SWITCH ..........................522
Component Description ........................................522
CONSULT-II Reference Value in Data Monitor Mode
.522
On Board Diagnosis Logic ....................................522
DTC Confirmation Procedure ...............................523
Wiring Diagram .....................................................524
Diagnostic Procedure ...........................................525
Component Inspection ..........................................530
DTC P1572 ASCD BRAKE SWITCH ......................532
Component Description ........................................532
CONSULT-II Reference Value in Data Monitor Mode
.532
On Board Diagnosis Logic ....................................532
DTC Confirmation Procedure ...............................533
Wiring Diagram .....................................................534Diagnostic Procedure ............................................535
Component Inspection ..........................................540
DTC P1574 ICC VEHICLE SPEED SENSOR .........541
Component Description ........................................541
On Board Diagnosis Logic ....................................541
DTC Confirmation Procedure ................................541
Diagnostic Procedure ............................................542
DTC P1574 ASCD VEHICLE SPEED SENSOR .....543
Component Description ........................................543
On Board Diagnosis Logic ....................................543
DTC Confirmation Procedure ................................543
Diagnostic Procedure ............................................544
DTC P1706 PNP SWITCH .......................................545
Component Description ........................................545
CONSULT-II Reference Value in Data Monitor Mode
.545
On Board Diagnosis Logic ....................................545
DTC Confirmation Procedure ................................545
Overall Function Check .........................................546
Wiring Diagram .....................................................547
Diagnostic Procedure ............................................548
DTC P1805 BRAKE SWITCH .................................550
Description ............................................................550
CONSULT-II Reference Value in Data Monitor Mode
.550
On Board Diagnosis Logic ....................................550
DTC Confirmation Procedure ................................550
Wiring Diagram .....................................................551
Diagnostic Procedure ............................................552
Component Inspection ..........................................554
DTC P2122, P2123 APP SENSOR .........................555
Component Description ........................................555
CONSULT-II Reference Value in Data Monitor Mode
.555
On Board Diagnosis Logic ....................................555
DTC Confirmation Procedure ................................556
Wiring Diagram .....................................................557
Diagnostic Procedure ............................................558
Component Inspection ..........................................560
Removal and Installation .......................................561
DTC P2127, P2128 APP SENSOR .........................562
Component Description ........................................562
CONSULT-II Reference Value in Data Monitor Mode
.562
On Board Diagnosis Logic ....................................562
DTC Confirmation Procedure ................................563
Wiring Diagram .....................................................564
Diagnostic Procedure ............................................565
Component Inspection ..........................................568
Removal and Installation .......................................568
DTC P2135 TP SENSOR ........................................569
Component Description ........................................569
CONSULT-II Reference Value in Data Monitor Mode
.569
On Board Diagnosis Logic ....................................569
DTC Confirmation Procedure ................................570
Wiring Diagram .....................................................571
Diagnostic Procedure ............................................572

EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: 2004 November 2004 FX35/FX45Component Inspection ......................................... 575
Removal and Installation ...................................... 575
DTC P2138 APP SENSOR ..................................... 576
Component Description ........................................ 576
CONSULT-II Reference Value in Data Monitor Mode
. 576
On Board Diagnosis Logic ................................... 576
DTC Confirmation Procedure ............................... 577
Wiring Diagram .................................................... 578
Diagnostic Procedure ........................................... 579
Component Inspection ......................................... 584
Removal and Installation ...................................... 584
IGNITION SIGNAL .................................................. 585
Component Description ........................................ 585
Wiring Diagram .................................................... 586
Diagnostic Procedure ........................................... 591
Component Inspection ......................................... 595
Removal and Installation ...................................... 596
INJECTOR CIRCUIT ............................................... 597
Component Description ........................................ 597
CONSULT-II Reference Value in Data Monitor Mode
. 597
Wiring Diagram .................................................... 598
Diagnostic Procedure ........................................... 599
Component Inspection ......................................... 602
Removal and Installation ...................................... 602
FUEL PUMP CIRCUIT ............................................ 603
Description ........................................................... 603
CONSULT-II Reference Value in Data Monitor Mode
. 603
Wiring Diagram .................................................... 604
Diagnostic Procedure ........................................... 605
Component Inspection ......................................... 608
Removal and Installation ...................................... 608
REFRIGERANT PRESSURE SENSOR ................. 609
Component Description ........................................ 609
Wiring Diagram .................................................... 610
Diagnostic Procedure ............................................ 611
Removal and Installation ...................................... 613
ELECTRICAL LOAD SIGNAL ................................ 614
Description ........................................................... 614
CONSULT-II Reference Value in Data Monitor Mode
. 614
Diagnostic Procedure ........................................... 614
ICC BRAKE SWITCH ............................................. 615
Component Description ........................................ 615
CONSULT-II Reference Value in Data Monitor Mode
. 615
Wiring Diagram .................................................... 616
Diagnostic Procedure ........................................... 617
Component Inspection ......................................... 622
ASCD BRAKE SWITCH ......................................... 624
Component Description ........................................ 624
CONSULT-II Reference Value in Data Monitor Mode
. 624
Wiring Diagram .................................................... 625
Diagnostic Procedure ........................................... 626
Component Inspection ......................................... 631ASCD INDICATOR ..................................................632
Component Description ........................................632
CONSULT-II Reference Value in Data Monitor Mode
.632
Wiring Diagram .....................................................633
Diagnostic Procedure ...........................................634
SNOW MODE SWITCH ..........................................635
Description ............................................................635
CONSULT-II Reference Value in the Data Monitor
Mode .....................................................................635
Wiring Diagram .....................................................636
Diagnostic Procedure ...........................................637
Component Inspection ..........................................640
MIL AND DATA LINK CONNECTOR ......................641
Wiring Diagram .....................................................641
EVAPORATIVE EMISSION SYSTEM .....................643
Description ............................................................643
Component Inspection ..........................................646
Removal and Installation ......................................647
How to Detect Fuel Vapor Leakage ......................647
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ....................................................................650
System Description ...............................................650
Diagnostic Procedure ...........................................651
Component Inspection ..........................................653
POSITIVE CRANKCASE VENTILATION ...............655
Description ............................................................655
Component Inspection ..........................................655
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .657
System Description ...............................................657
Component Description ........................................659
SERVICE DATA AND SPECIFICATIONS (SDS) ....660
Fuel Pressure .......................................................660
Idle Speed and Ignition Timing .............................660
Calculated Load Value ..........................................660
Mass Air Flow Sensor ...........................................660
Intake Air Temperature Sensor .............................660
Engine Coolant Temperature Sensor ...................660
Heated Oxygen Sensor 1 Heater .........................660
Heated Oxygen sensor 2 Heater ..........................660
Crankshaft Position Sensor (POS) .......................660
Camshaft Position Sensor (PHASE) ....................660
Throttle Control Motor ...........................................660
Injector ..................................................................661
Fuel Pump ............................................................661
VK45DE
INDEX FOR DTC .....................................................662
Alphabetical Index ................................................662
DTC No. Index ......................................................665
PRECAUTIONS ......................................................670
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................670
On Board Diagnostic (OBD) System of Engine and
A/T ........................................................................670
Precaution ............................................................670
Wiring Diagrams and Trouble Diagnosis ..............673

EC-13
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: 2004 November 2004 FX35/FX45Wiring Diagram ...................................................1176
Diagnostic Procedure ..........................................1177
Component Inspection ........................................1180
DTC P1564 ASCD STEERING SWITCH ...............1181
Component Description .......................................1181
CONSULT-II Reference Value in Data Monitor Mode
1181
On Board Diagnosis Logic ..................................1181
DTC Confirmation Procedure ..............................1182
Wiring Diagram ...................................................1183
Diagnostic Procedure ..........................................1184
Component Inspection ........................................1187
DTC P1568 ICC FUNCTION ..................................1188
On Board Diagnosis Logic ..................................1188
DTC Confirmation Procedure ..............................1188
Diagnostic Procedure ..........................................1188
DTC P1572 ICC BRAKE SWITCH ........................1189
Component Description .......................................1189
CONSULT-II Reference Value in Data Monitor Mode
1189
On Board Diagnosis Logic ..................................1189
DTC Confirmation Procedure ..............................1190
Wiring Diagram ...................................................1191
Diagnostic Procedure ..........................................1192
Component Inspection ........................................1197
DTC P1572 ASCD BRAKE SWITCH ....................1199
Component Description .......................................1199
CONSULT-II Reference Value in Data Monitor Mode
1199
On Board Diagnosis Logic ..................................1199
DTC Confirmation Procedure ..............................1200
Wiring Diagram ...................................................1201
Diagnostic Procedure ..........................................1202
Component Inspection ........................................1206
DTC P1574 ICC VEHICLE SPEED SENSOR .......1207
Component Description .......................................1207
On Board Diagnosis Logic ..................................1207
DTC Confirmation Procedure ..............................1207
Diagnostic Procedure ..........................................1208
DTC P1574 ASCD VEHICLE SPEED SENSOR ...1209
Component Description .......................................1209
On Board Diagnosis Logic ..................................1209
DTC Confirmation Procedure ..............................1209
Diagnostic Procedure ..........................................1210
DTC P1706 PNP SWITCH .....................................1211
Component Description .......................................1211
CONSULT-II Reference Value in Data Monitor Mode
1211
On Board Diagnosis Logic ..................................1211
DTC Confirmation Procedure ..............................1211
Overall Function Check .......................................1212
Wiring Diagram ...................................................1213
Diagnostic Procedure ..........................................1214
DTC P1720 VEHICLE SPEED SENSOR (A/T OUT-
PUT) .......................................................................1216
Description ..........................................................1216
CONSULT-II Reference Value in Data Monitor Mode
1216
On Board Diagnosis Logic ..................................1216DTC Confirmation Procedure ..............................1216
Diagnostic Procedure ..........................................1217
DTC P1780 SHIFT CHANGE SIGNAL ..................1218
Description ...........................................................1218
On Board Diagnosis Logic ...................................1218
DTC Confirmation Procedure ..............................1218
Diagnostic Procedure ..........................................1218
DTC P1805 BRAKE SWITCH ................................1220
Description ...........................................................1220
CONSULT-II Reference Value in Data Monitor Mode
1220
On Board Diagnosis Logic ...................................1220
DTC Confirmation Procedure ..............................1220
Wiring Diagram ....................................................1221
Diagnostic Procedure ..........................................1222
Component Inspection .........................................1224
DTC P2122, P2123 APP SENSOR ........................1225
Component Description .......................................1225
CONSULT-II Reference Value in Data Monitor Mode
1225
On Board Diagnosis Logic ...................................1225
DTC Confirmation Procedure ..............................1226
Wiring Diagram ....................................................1227
Diagnostic Procedure ..........................................1228
Component Inspection .........................................1230
Removal and Installation .....................................1231
DTC P2127, P2128 APP SENSOR ........................1232
Component Description .......................................1232
CONSULT-II Reference Value in Data Monitor Mode
1232
On Board Diagnosis Logic ...................................1232
DTC Confirmation Procedure ..............................1233
Wiring Diagram ....................................................1234
Diagnostic Procedure ..........................................1235
Component Inspection .........................................1238
Removal and Installation .....................................1238
DTC P2135 TP SENSOR .......................................1239
Component Description .......................................1239
CONSULT-II Reference Value in Data Monitor Mode
1239
On Board Diagnosis Logic ...................................1239
DTC Confirmation Procedure ..............................1240
Wiring Diagram ....................................................1241
Diagnostic Procedure ..........................................1242
Component Inspection .........................................1245
Removal and Installation .....................................1245
DTC P2138 APP SENSOR ....................................1246
Component Description .......................................1246
CONSULT-II Reference Value in Data Monitor Mode
1246
On Board Diagnosis Logic ...................................1246
DTC Confirmation Procedure ..............................1247
Wiring Diagram ....................................................1248
Diagnostic Procedure ..........................................1249
Component Inspection .........................................1253
Removal and Installation .....................................1253
VARIABLE INDUCTION AIR CONTROL SYSTEM
(VIAS) .....................................................................1254
Description ...........................................................1254

EC-14Revision: 2004 November 2004 FX35/FX45CONSULT-II Reference Value in Data Monitor Mode
1255
Wiring Diagram ....................................................1256
Diagnostic Procedure ..........................................1257
Component Inspection .........................................1260
Removal and Installation .....................................1261
IGNITION SIGNAL .................................................1262
Component Description .......................................1262
Wiring Diagram ....................................................1263
Diagnostic Procedure ..........................................1268
Component Inspection .........................................1272
Removal and Installation .....................................1273
INJECTOR CIRCUIT ..............................................1274
Component Description .......................................1274
CONSULT-II Reference Value in Data Monitor Mode
1274
Wiring Diagram ....................................................1275
Diagnostic Procedure ..........................................1276
Component Inspection .........................................1279
Removal and Installation .....................................1279
FUEL PUMP CIRCUIT ...........................................1280
Description ...........................................................1280
CONSULT-II Reference Value in Data Monitor Mode
1280
Wiring Diagram ....................................................1281
Diagnostic Procedure ..........................................1282
Component Inspection .........................................1285
Removal and Installation .....................................1286
REFRIGERANT PRESSURE SENSOR .................1287
Component Description .......................................1287
Wiring Diagram ....................................................1288
Diagnostic Procedure ..........................................1289
Removal and Installation .....................................1291
ELECTRICAL LOAD SIGNAL ...............................1292
Description ...........................................................1292
CONSULT-II Reference Value in Data Monitor Mode
1292
Diagnostic Procedure ..........................................1292
ICC BRAKE SWITCH .............................................1293
Component Description .......................................1293
CONSULT-II Reference Value in Data Monitor Mode
1293
Wiring Diagram ....................................................1294
Diagnostic Procedure ..........................................1295
Component Inspection .........................................1301
ASCD BRAKE SWITCH .........................................1302
Component Description .......................................1302
CONSULT-II Reference Value in Data Monitor Mode
1302Wiring Diagram ....................................................1303
Diagnostic Procedure ...........................................1304
Component Inspection .........................................1308
ASCD INDICATOR .................................................1309
Component Description .......................................1309
CONSULT-II Reference Value in Data Monitor Mode
1309
Wiring Diagram ....................................................1310
Diagnostic Procedure ...........................................1311
SNOW MODE SWITCH ..........................................1312
Description ...........................................................1312
CONSULT-II Reference Value in the Data Monitor
Mode ....................................................................1312
Wiring Diagram ....................................................1313
Diagnostic Procedure ...........................................1314
Component Inspection .........................................1317
MIL AND DATA LINK CONNECTOR .....................1318
Wiring Diagram ....................................................1318
EVAPORATIVE EMISSION SYSTEM ....................1320
Description ...........................................................1320
Component Inspection .........................................1323
Removal and Installation ......................................1324
How to Detect Fuel Vapor Leakage .....................1324
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ...................................................................1327
System Description ..............................................1327
Diagnostic Procedure ...........................................1328
Component Inspection .........................................1330
POSITIVE CRANKCASE VENTILATION ...............1332
Description ...........................................................1332
Component Inspection .........................................1332
AUTOMATIC SPEED CONTROL DEVICE (ASCD) 1334
System Description ..............................................1334
Component Description .......................................1335
SERVICE DATA AND SPECIFICATIONS (SDS) ...1336
Fuel Pressure .......................................................1336
Idle Speed and Ignition Timing .............................1336
Calculated Load Value .........................................1336
Mass Air Flow Sensor ..........................................1336
Intake Air Temperature Sensor ............................1336
Engine Coolant Temperature Sensor ...................1336
Heated Oxygen Sensor 1 Heater .........................1336
Heated Oxygen Sensor 2 Heater .........................1336
Crankshaft Position Sensor (POS) ......................1336
Camshaft Position Sensor (PHASE) ....................1336
Throttle Control Motor ..........................................1336
Injector .................................................................1337
Fuel Pump ............................................................1337

INDEX FOR DTC
EC-15
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2004 November 2004 FX35/FX45
[VQ35DE]INDEX FOR DTCPFP:00024
Alphabetical IndexABS006JV
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-142, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
×:Applicable —: Not applicable
Items
(CONSULT-II screen terms)DTC*
1
TripMIL lighting
upReference page
CONSULT-II
GST*
2ECM*3
A/T INTERLOCK P1730 1730 1×AT- 1 4 7
A/T TCC S/V FNCTN P0744 0744 2×AT- 1 2 5
ACC COMMAND VALUE*8P1568 1568 1 —EC-521
APP SEN 1/CIRC P2122 2122 1×EC-555
APP SEN 1/CIRC P2123 2123 1×EC-555
APP SEN 2/CIRC P2127 2127 1×EC-562
APP SEN 2/CIRC P2128 2128 1×EC-562
APP SENSOR P2138 2138 1×EC-576
ASCD BRAKE SW*7P1572 1572 1 —EC-522, EC-532
ASCD SW*7P1564 1564 1 —EC-508, EC-515
ASCD VHL SPD SEN*7P1574 1574 1 —EC-541, EC-543
ATF TEMP SEN/CIRC P0710 0710 2×AT- 1 3 9
BRAKE SW/CIRCUIT P1805 1805 2 —EC-550
CAN COMM CIRCUIT U1000
1000*51×EC-142
CAN COMM CIRCUIT U1001
1001*52—EC-142
CKP SEN/CIRCUIT P0335 0335 2×EC-302
CLOSED LOOP-B1 P1148 1148 1×EC-468
CLOSED LOOP-B2 P1168 1168 1×EC-468
CMP SEN/CIRC-B1 P0340 0340 2×EC-308
CMP SEN/CIRC-B2 P0345 0345 2×EC-308
CTP LEARNING P1225 1225 2 —EC-485
CTP LEARNING P1226 1226 2 —EC-487
CYL 1 MISFIRE P0301 0301 2×EC-291
CYL 2 MISFIRE P0302 0302 2×EC-291
CYL 3 MISFIRE P0303 0303 2×EC-291
CYL 4 MISFIRE P0304 0304 2×EC-291
CYL 5 MISFIRE P0305 0305 2×EC-291
CYL 6 MISFIRE P0306 0306 2×EC-291
D/C SOLENOID/CIRC P1762 1762 1×AT- 1 6 0
D/C SOLENOID FNCTN P1764 1764 1×AT- 1 6 2
ECM P0605 0605 1 or 2× or —EC-401
ECM BACK UP/CIRCUIT P1065 1065 2×EC-404
ECT SEN/CIRCUIT P0117 0117 1×EC-185
ECT SEN/CIRCUIT P0118 0118 1×EC-185
ECT SENSOR P0125 0125 1×EC-197
ENG OVER TEMP P1217 1217 1×EC-472