remote control INFINITI FX35 2005 User Guide

BL-2Revision: 2005 July 2005 FX
CHECK DOOR SWITCH (EXCEPT BACK DOOR
SWITCH) .......................................................... ... 42
CHECK BACK DOOR SWITCH ....................... ... 44
Check Key Switch ................................................ ... 46
Check Door Lock and Unlock Switch .................. ... 48
Check Door Lock Actuator (Driver Side) .............. ... 50
Check Door Lock Actuator (Passenger Side and
Rear LH/RH) ........................................................ ... 51
Check Fuel Lid Opener Actuator ......................... ... 52
Check Front Door Key Cylinder Switch (Lock) .... ... 53
Check Front Door Key Cylinder Switch (Unlock) . ... 54
Check Select Unlock Relay Circuit ...................... ... 55
REMOTE KEYLESS ENTRY SYSTEM .................. ... 56
Component Parts and Harness Connector Location ... 56
System Description .............................................. ... 57
INPUTS ............................................................ ... 57
OPERATED PROCEDURE .............................. ... 58
CAN Communication System Description ........... ... 59
CAN Communication Unit .................................... ... 59
Schematic ............................................................ ... 60
Wiring Diagram — KEYLES— ............................. ... 61
FIG. 1 ................................................................ ... 61
FIG. 2 ................................................................ ... 62
FIG. 3 ................................................................ ... 63
Terminals and Reference Value for BCM ............. ... 64
Terminals and Reference Value for IPDM E/R ..... ... 65
CONSULT-II Function (BCM) ............................... ... 66
CONSULT-II INSPECTION PROCEDURE ....... ... 66
CONSULT-II APPLICATION ITEMS ................. ... 67
Work Flow ............................................................ ... 69
Trouble Diagnosis Chart by Symptom ................. ... 70
Check Key Fob Battery and Function .................. ... 72
Check ACC Switch .............................................. ... 73
Check Door Switch .............................................. ... 74
CHECK DOOR SWITCH (EXCEPT BACK DOOR
SWITCH) .......................................................... ... 74
CHECK BACK DOOR SWITCH ....................... ... 76
Check Key Switch ................................................ ... 78
Check Remote Keyless Entry Receiver ............... ... 79
Check IPDM E/R Operation ................................. ... 82
Check Hazard Warning Lamp Function ............... ... 83
Check Horn Function ........................................... ... 83
Check Headlamp Function .................................. ... 83
Check Map Lamp and Ignition Keyhole Illumination
Function ............................................................... ... 83
ID Code Entry Procedure .................................... ... 84
KEY FOB ID SET UP WITH CONSULT-II ........ ... 84
KEY FOB ID SET UP WITHOUT CONSULT-II . ... 86
Removal and Installation of Remote keyless Entry
receiver ................................................................ ... 87
REMOVAL ........................................................ ... 87
INSTALLATION ................................................. ... 87
Key Fob Battery Replacement ............................. ... 88
INTELLIGENT KEY SYSTEM ................................ ... 89
Component Parts and Harness Connector Location ... 89
System Description .............................................. ... 91
DOOR LOCK FUNCTION ................................ ... 91
REMOTE CONTROL ENTRY FUNCTIONS ..... ... 92
ENGINE STARTUP FUNCTION ....................... ... 93 WARNING AND ALARM FUNCTION ...............
... 94
CHANGE SETTINGS FUNCTION .................... ... 97
INTELLIGENT KEY REGISTRATION ............... ... 97
STEERING LOCK UNIT REGISTRATION ........ ... 97
CAN Communication System Description ........... ... 98
CAN Communication Unit .................................... ... 98
Schematic ............................................................ ... 99
Wiring Diagram — I/KEY— .................................. .101
Terminals and Reference Value for INTELLIGENT
KEY UNIT ............................................................ .114
Terminals and Reference Value for Steering Lock
unit ....................................................................... .116
Terminals and Reference Value for BCM ............. .116
Terminals and Reference Value for IPDM E/R ..... .117
Diagnosis Procedure ............................................ .118
WORK FLOW ................................................... .118
CONSULT-II Functions ........................................ .119
CONSULT-II Inspection Procedure ...................... .119
BASIC OPERATION ......................................... .119
CONSULT-II Application Items ............................. .120
WORK SUPPORT ............................................ .120
SELF-DIAGNOSTIC RESULTS ........................ .120
DATA MONITOR ............................................... .120
ACTIVE TEST ................................................... .121
List of Operation Related Parts ............................ .122
Trouble Diagnosis Symptom Chart ...................... .123
ALL FUNCTIONS OF THE INTELLIGENT KEY
ARE NOT OPERATING .................................... .123
REMOTE CONTROL ENTRY FUNCTION MAL-
FUNCTION ....................................................... .123
DOOR LOCK FUNCTION MALFUNCTION ...... .124
ENGINE START FUNCTION MALFUNCTION . .125
WARNING CHIME FUNCTION MALFUNCTION .125
Check CAN Communication System Inspection .. .128
Check Intelligent Key Unit Power Supply and
Ground Circuit ...................................................... .129
Check Key Switch (Intelligent Key Unit Input) ...... .129
Check Key Switch (BCM Input) ............................ .131
Check Ignition Knob Switch ................................. .132
Check Door Switch .............................................. .133
CHECK DOOR SWITCH (EXCEPT BACK DOOR
SWITCH) ........................................................... .133
CHECK BACK DOOR SWITCH ........................ .134
Check Unlock Sensor .......................................... .136
Check Door Request Switch ................................ .137
Check Intelligent Key Warning Buzzer ................. .139
Check Outside Key Antenna ................................ .140
Check Inside Key Antenna ................................... .143
Check Steering Lock Unit ..................................... .144
Check Stop Lamp Switch ..................................... .146
Check Detention Switch ....................................... .147
Check Select Unlock Relay .................................. .149
Check Hazard Function ....................................... .150
Check Horn Function ........................................... .150
Check Headlamp Function ................................... .150
Check IPDM E/R Operation ................................. .150
Removal and Installation of Intelligent Key Unit ... .151
REMOVAL ......................................................... .151

REMOTE KEYLESS ENTRY SYSTEM BL-57
C
D E
F
G H
J
K L
M A
B
BL
Revision: 2005 July 2005 FX
System DescriptionAIS004MB
INPUTS
Power is supplied at all times

to BCM terminal 55

through 50A fusible link (letter M , located in the fuse and fusible link box).

to BCM terminal 42

through 15A fuse (No. 22, located in the fuse and fusible link box).
When the key switch is ON (key is inserted in ignition key cylinder), power is supplied

to BCM terminal 37

through key switch terminal 1 and 2

through 15A fuse (No. 22, located in the fuse and fusible link box).
When the ignition switch is ACC or ON, power is supplied

to BCM terminal 11

through 10A fuse [No. 6, located in the fuse block (J/B)].
When the ignition switch is ON or START, power is supplied

to BCM terminal 38

through 15A fuse [No. 1, located in the fuse block (J/B)].
When the front door switch (driver side) is ON (door is OPEN), ground is supplied

to BCM terminal 62

through front door switch (driver side) terminal 1

through front door switch (driver side) case ground.
When the front door switch (passenger side) is ON (door is OPEN), ground is supplied

to BCM terminal 12

through front door switch (passenger side) terminal 1

through front door switch (passenger side) case ground.
When the rear door switch LH is ON (door is OPEN), ground is supplied

to BCM terminal 63

through rear door switch LH terminal 1

through rear door switch LH case ground.
When the rear door switch RH is ON (door is OPEN), ground is supplied

to BCM meter terminal 13

through rear door switch RH terminal 1

through rear door switch RH case ground.
When the back door switch is ON (door is open), ground is supplied

to BCM terminal 58

through back door closure motor (door switch) terminals 7 and 8

through body grounds B15 and B45
Key fob signal is inputted to remote keyless entry receiver (the antenna of the system is built in remote keyless
entry receiver).

to BCM terminal 20

from remote keyless entry system controls operation of the
The remote keyless entry system controls operation of the

power door lock

hazard and horn reminder

auto door lock

panic alarm

keyless power window down (open)

room lamp and key ring illumination

BL-58
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2005 July 2005 FX
OPERATED PROCEDURE
Power Door Lock Operation
BCM receives a LOCK signal from key fob. BCM locks all doors with input of LOCK signal from key fob.
When an UNLOCK signal is sent from key fob once, driver's door will be unlocked.
Then, if an UNLOCK signal is sent from key fob again within 5 seconds, all other door will be unlocked.
Power door lock operation mode can be changed using “DOOR LOCK-UNLOCK SET” mode in “WORK SUP-
PORT” of “POWER DOOR LOCK SYSTEM”.
Refer to BL-68, "
Work Support" .
Power door lock operation mode can be changed also on the display.
Refer to AV- 6 0 , "
SETTING SCREEN" . (without navigation system)
Refer to AV- 9 4 , "
Vehicle Electronic Systems" . (with navigation system)
Hazard and Horn Reminder
When the doors are locked or unlocked by key fob, power is supplied to hazard warning lamp and lamp flash
as follows

LOCK operation: C mode (flash twice) or S mode (flash twice)

UNLOCK operation: C mode (flash once) or S mode (do not flash)
BCM outputs to IPDM E/R for horn reminder signal as DATA LINE (CAN H line and CAN L line).
The hazard and horn reminder has C mode (horn chirp mode) and S mode (non-horn chirp mode).
Operating function of hazard and horn reminder
Hazard and horn reminder do not operate if any door switch is ON (any door is OPEN).
How to change hazard and horn reminder mode
With CONSULT-II
Hazard and horn reminder can be changed using “MULTI ANSWER BACK SET” mode in “WORK SUPPORT”.
Refer to BL-68, "
Work Support" .
Without CONSULT-II
When LOCK and UNLOCK signals are sent from the key fob for more than 2 seconds at the same time, the
hazard and horn reminder mode is changed and hazard warning lamp flashes and horn sounds as follows:
Auto Door Lock Operation
Auto lock function signal is sent for operation when any of the following signals are not sent within 1 minute
after the unlock signal is sent from the key fob:

when door switch is turned ON for open.

when the key switch is turned ON.

when the lock signal is sent from the key fob.
Auto door lock mode can be changed using “AUTO LOCK SET” mode in “WORK SUPPORT”.
Refer to BL-68, "
Work Support" .
Auto door lock mode can be changed also on the display.
C mode S mode
Remote controller
operation Lock Unlock Lock Unlock
Hazard warning lamp
flash Twice Once Twice —
Horn sound Once — — —
SEL153WA

REMOTE KEYLESS ENTRY SYSTEM BL-59
C
D E
F
G H
J
K L
M A
B
BL
Revision: 2005 July 2005 FX
Refer to AV- 6 0 , "SETTING SCREEN" . (without navigation system)
Refer to AV- 9 4 , "
Vehicle Electronic Systems" . (with navigation system)
Panic Alarm Operation
When key switch is OFF (when ignition key is not inserted in key cylinder), BCM turns on and off horn and
headlamp intermittently with input of PANIC ALARM signal from key fob.
The alarm automatically turns off after 25 seconds or when BCM receives any signal from key fob.
Panic alarm operation mode can be changed using “PANIC ALARM SET” mode in “WORK SUPPORT”.
Refer to BL-68, "
Work Support" .
For detailed description, refer to BL-186, "
VEHICLE SECURITY (THEFT WARNING) SYSTEM" .
Keyless Power Window Down (Open) Operation
When key fob unlock switch is turned ON with ignition switch OFF, and key fob unlock switch is detected to be
on continuously for 3 seconds, the driver's door and passenger's door power windows are simultaneously
opened.
Power window is operated to open and the operation continues as long as the key fob unlock switch is
pressed.
Keyless power window down operation mode can be changed using “PW DOWN SET” mode in “WORK SUP-
PORT”. Refer to BL-68, "
Work Support"
Room Lamp and Ignition Key Ring Illumination Operation
When the following conditions come:

condition of interior lamp switch is DOOR position;

door switch OFF (when all the doors are closed);
Remote keyless entry system turns on interior lamp (for 30 seconds) with input of UNLOCK signal from key
fob. For detailed description, refer to LT- 1 5 9 , "
INTERIOR ROOM LAMP" .
CAN Communication System DescriptionAIS004MC
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitAIS004RM
Refer to LAN-30, "CAN COMMUNICATION" .

BL-66
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2005 July 2005 FX
CONSULT-II Function (BCM)AIS004MH
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
*: Refer to BCS-15, "CAN Communication Inspection Using CONSULT-II (Self-Diagnosis)" .
CONSULT-II INSPECTION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Turn ignition switch “OFF”.
2. Connect “CONSULT-II” and “CONSULT-II CONVERTER” to the data link connector.
3. Turn ignition switch “ON”.
4. Touch “START (NISSAN BASED VHCL)”.
5. Touch “BCM”. If “BCM” is not indicated, go to GI-39, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
BCM diagnosis
position Inspection items and diagnosis mode Description
BCM C/U* Self-diagnosis results Carries out the self-diagnosis.
DATA MONI-
TOR CAN diagnosis support
monitor Displays CAN communication system diagnosis, disabled
transmission status, and communication status of each unit
communicated with BCM.
Selection from menu Displays the input data to BCM on real-time basis.
MULTI REMOTE
ENT DATA MONITOR
Displays the input remote keyless entry system data to BCM
on real–time basis.
ACTIVE TEST Gives a drive to a load to check the operation.
WORK SUPPORT Changes the setting for each function.
PBIB1503E
BCIA0029E
BCIA0030E

BL-84
REMOTE KEYLESS ENTRY SYSTEM
Revision: 2005 July 2005 FX
ID Code Entry ProcedureAIS004MT
KEY FOB ID SET UP WITH CONSULT-II
NOTE:

If a key fob is lost, the ID code of the lost key fob must be erased to prevent unauthorized use. A
specific ID code can be erased with CONSULT-II. However, when the ID code of a lost key fob is not
known, all controller ID codes should be erased. After all ID codes are erased, the ID codes of all
remaining and/or new key fobs must be re-registered.

When registering an additional key fob, the existing ID codes in memory may or may not be
erased. If four ID codes are stored in memory, when an additional code is registered, only the old-
est code is erased. If less than five ID codes are stored in memory, when an additional ID code is
registered, the new ID code is added and no ID codes are erased.

Entry of maximum five ID codes is allowed. When more than four ID codes are entered, the oldest
ID code will be erased.

Even if same ID code that is already in the memory is input, the same ID code can be entered. The
code is counted as an additional code.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Turn ignition switch “OFF”.
2. Connect “CONSULT-II” and “CONSULT-II CONVERTER” to the data link connector.
3. Turn ignition switch ON.
4. Touch “START (NISSAN BASED VHCL)”.
5. Touch “BCM”. If “BCM” is not indicated, go to GI-39, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
PBIB1503E
BCIA0029E
BCIA0030E

REMOTE KEYLESS ENTRY SYSTEM BL-87
C
D E
F
G H
J
K L
M A
B
BL
Revision: 2005 July 2005 FX
NOTE:

If a key fob is lost, the ID code of the lost key fob must be erased to prevent unauthorized use. A specific
ID code can be erased with CONSULT-II. However, when the ID code of a lost key fob is not known, all
controller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or
new key fobs must be re-registered.
To erase all ID codes in memory, register one ID code (key fob) five times. After all ID codes are erased,
the ID codes of all remaining and/or new key fobs must be re-registered.

When registering an additional key fob, the existing ID codes in memory may or may not be erased. If five
ID codes are stored in memory, when an additional code is registered, only the oldest code is erased. If
less than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is
added and no ID codes are erased.

If you need to activate more than two additional new key fobs, repeat the procedure “Additional ID code
entry” for each new key fob.

Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest ID code
will be erased.

Even if same ID code that is already in the memory is input, the same ID code can be entered. The code
is counted as an additional code.
Removal and Installation of Remote keyless Entry receiverAIS006A2
REMOVAL
1. Remove the instrument passenger lower panel. Refer to IP-18, "INSTRUMENT PASSENGER LOWER
PA N E L" .
2. Disconnect remote keyless entry receiver harness connector, remove screw and remote keyless entry receiver.
INSTALLATION
Install in the reverse order of removal.
PIIB4073E

INTELLIGENT KEY SYSTEM BL-91
C
D E
F
G H
J
K L
M A
B
BL
Revision: 2005 July 2005 FXSystem DescriptionAIS004MW

The Intelligent Key system is a system which can lock and unlock the doors (door lock function) and start
the engine (engine start function) by carrying around the Intelligent Key, which operates based on the
results of electrical key-ID verification using two-way communications between the Intelligent Key and the
vehicle

Operation of the remote control buttons on the Intelligent Key also provides the same functions as the
remote control entry system. (Remote control entry functions)

As an ignition key warning function, when a door is locked or unlocked with entry switch or remote control-
ler button operation, the hazard lamps flash and the Intelligent Key warning buzzer sounds.

Even if the vehicle or Intelligent Key battery runs down, the door can be locked and unlocked and the
engine started with the mechanical key built into the Intelligent Key.

If an Intelligent Key was lost, a new Intelligent Key can be registered. A maximum of 4 Intelligent Keys can
be registered.

It has been made possible to diagnose the system, change the function setting and register an Intelligent
Key with the CONSULT-II.
DOOR LOCK FUNCTION
Operation Description

When the driver door, passenger door, or back door request switch is pressed, Intelligent Key unit sends a
request signal from the transmission antenna corresponding to the pressed door request switch, key-ID
verification is performed using two-way communication with Intelligent Key, and if ID is successfully veri-
fied, a door lock/unlock request signal is sent to BCM (Body Control Module) using CAN communication
to lock/unlock the door lock.

When door is locking, door is unlocked, when door is unlocking, door is locked.

When door is locked/unlocked by door request switch operation, hazard lamps flash and Intelligent Key
warning buzzer sounds.

With the locking operation of door request switch, door lock actuators of all door are locked.
PIIB4645E

BL-92
INTELLIGENT KEY SYSTEM
Revision: 2005 July 2005 FX
Driver side door request switch operation

When door request switch (driver side) is pushed (unlock), driver side door lock actuator is unlocked.
(Selective door unlock function)

When door request switch (driver side) is pushed (unlock) for the second time within 5 seconds after the
first operation, door lock actuators on passenger's and other's doors are unlocked.

Unlock mode can be changed using “WORK SUPPORT” mode in “SELECTIVE UNLOCK FUNCTION”.
Refer to BL-120, "
WORK SUPPORT" .
Passenger side door request switch operation

When door request switch (passenger side) is pushed (unlock), passenger side door lock actuator is
unlocked.

When door request switch (passenger side) is pushed (unlock) for the second time with in 5 seconds after
the first operation, door lock actuators on driver's and other's doors are unlocked.

Unlock mode can be changed using “WORK SUPPORT” mode in “SELECTIVE UNLOCK FUNCTION”.
Refer to BL-120, "
WORK SUPPORT" .
Back door request switch operation

When back door request switch is pushed (unlock), back door lock actuator is unlocked.

When back door request switch is pushed (unlock) for the second time with in 5 seconds after the first
operation, door lock actuators on driver's and passenger's doors are unlocked.

Unlock mode can be changed using “WORK SUPPORT” mode in “SELECTIVE UNLOCK FUNCTION”.
Refer to BL-120, "
WORK SUPPORT" .
Operation Condition
Auto Door Lock Function
After the door request switch in the driver or passenger or back door is operated and the vehicle door is
unlocked, all the doors are automatically locked unless the mechanical key is inserted into the ignition knob,
the ignition knob is pressed, any door request switch is pressed, any one of the doors is opened, or an Intelli-
gent Key remote control button is operated within 30 seconds.
Key Reminder Function
The hazard lamps will flash and the Intelligent Key warning buzzer will sound several times when the door lock
is locked or unlocked by door request switch operation.
When ignition switch ON or any door is opened, key reminder function is not operate.
Intelligent Key Lock-in Prevention Function
When doors are locked using door lock and unlock switch or driver door lock knob while Intelligent key is in
vehicle and doors open, Intelligent Key unit sends door unlock request signal to BCM via CAN communication
to unlock all doors to prevent Intelligent Key from becoming locked in vehicle.
CAUTION:
The above function operates when the Intelligent Key is inside the vehicle. However, there are cases
that Intelligent Key cannot be detected and this function will not operate when Intelligent Key is on the
instrument panel, rear parcel shelf, or in the glove box. Also, this system sometimes does not operate
if the Intelligent Key is in the door pocket for the open door.
REMOTE CONTROL ENTRY FUNCTIONS
Door Lock Function

Operating a remote controller button on the Intelligent Key sends the Intelligent Key-ID to the Intelligent
Key unit. Intelligent Key unit conducts a verification of the received key-ID, and if the verification is
Request switch operation Operating conditions (When all the conditions below are met)
Door request switch (Driver side)

Closing all doors (door switch: OFF)

The Intelligent Key is in the antenna detection area for the door for which the door
request switch (LOCK) was operated.
Door request switch (passenger side)
Door request switch (back door)
Vehicle operation Hazard lamp Intelligent Key warning buzzer
Door unlock operation Once Once
Door lock operation Twice Twice

INTELLIGENT KEY SYSTEM BL-93
C
D E
F
G H
J
K L
M A
B
BL
Revision: 2005 July 2005 FX
accepted, a door lock or door unlock request signal is sent to BCM via CAN communication to lock/unlock
the door.

When door lock/unlock is performed using Intelligent Key remote controller button operation, operation
confirmation is conducted by making hazard lamps flash and Intelligent Key warning buzzer sound.
OPERATION CONDITION
Door lock/unlock operation is necessary for all doors close.
Map Lamp And Keyhole Illumination Function
When the following conditions come:

condition of map lamp switch is DOOR position;

door switch OFF (when all the doors are closed);
Remote control button of Intelligent Key turns on interior lamp (for 30 seconds) with input of UNLOCK signal
from Intelligent Key.
Panic Alarm Function
When key switch is OFF and ignition knob is not pushed (when mechanical key is not inserted in ignition
knob), BCM turns ON and OFF horn and headlamp intermittently with input of PANIC ALARM signal from
Intelligent Key. The alarm automatically turns off after 25 seconds or when Intelligent Key unit receives any
signal from Intelligent Key.
Panic alarm operation mode can be changed using “WORK SUPPORT” mode in “PANIC ALARM DELAY”.
Refer to BL-120, "
WORK SUPPORT" .
Remote Control Power Window Down (Open) Operation
When Intelligent Key unlock switch is turned ON with ignition switch OFF, and Intelligent Key unlock switch is
detected to be on continuously for 3 seconds, the driver's door and passenger's door power windows are
simultaneously opened.
Power window is operated to open and the operation continues as long as the Intelligent Key unlock switch is
pressed.
Remote control power window down operation mode can be changed using “P/W DOWN DELAY” mode in
“WORK SUPPORT”. Refer to BL-120, "
WORK SUPPORT" .
Key Reminder Function
As an operation verification function, when doors are locked or unlocked using Intelligent Key remote control-
ler button operation, hazard lamps flash and horn sounds.
ENGINE STARTUP FUNCTION
Operation Description

When ignition knob is pressed, Intelligent Key unit sends request signal from inside key antenna, key-ID
verification is conducted with Intelligent Key using two-way communication, and if verification is success-
ful, an ignition rotation prohibition latch release signal is sent to steering lock unit. Steering lock unit
releases ignition knob rotation prohibition latch. (Ignition knob can now be turned.)

When it becomes possible to rotate the ignition knob, “KEY” warning lamp in combination meter lights up
green to notify driver that ignition knob can be turned.
NOTE:
When it becomes impossible to rotate the ignition knob, “KEY” warning lamp in combination meter lights
up red.

When key-ID verification is successful and ignition knob switch is in the ON state, Intelligent Key unit uses
CAN communication to send engine start permission signal to BCM.

When BCM receives engine start permission signal, it uses CAN communication to sent starter request
signal to IPDM E/R so that the engine will start when ignition knob is rotated to START position.
Operation Range
Engine can be started when Intelligent Key is in the vehicle. However, sometimes engine might not start when
Intelligent Key is on instrument panel, rear parcel shelf, or in glove box.
Vehicle operation Hazard lamp Horn
Door unlocking operation Once —
Door locking operation Twice Once