INFINITI FX35 2005 Service Manual

EI-32
ROOF SIDE MOLDING
Revision: 2005 July 2005 FX
ROOF SIDE MOLDINGPFP:73854
Removal and InstallationAIS0037J
REMOVAL
Disconnect molding from roof side clip and remove roof side molding.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
To install roof side molding, check if all clips are matched over holes of panel on vehicle, then push it.
PIIA4951E
1. Roof side molding

ROOF RAIL EI-33
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
ROOF RAILPFP:73820
Removal and InstallationAIS0037K
REMOVAL
1. Remove cover roof rail (front/rear).
2. Remove nuts of roof rail and remove roof rail assembly.
INSTALLATION
Install in the reverse order of removal.
REMOVAL AND INSTALLATION OF ROOF RAIL BRACKET
Removal
1. Remove roof rail assembly.
2. Remove roof side molding. Refer to EI-32, "
ROOF SIDE MOLDING" .
3. Remove headlining. Refer to EI-41, "
HEADLINING" .
4. Remove nuts of roof rail bracket assembly and remove roof rail bracket assembly.
Installation
Install in the reverse order of removal.
CAUTION:
Replace sealing washer.
1. Cover roof rail (front) 2. Nut 3. Roof rail assembly
4. Rubber seal (front) 5. Roof side molding 6. Roof rail bracket assembly
7. Seal 8. Nut 9. Rubber seal (rear)
10. Cover roof rail (rear)
PIIA4948E

EI-34
DOOR FINISHER
Revision: 2005 July 2005 FX
DOOR FINISHERPFP:80900
Removal and InstallationAIS003BT
DOOR FINISHER (FRONT AND REAR)
Removal
1. Remove door finisher cap of inside handle portion and remove bolt.
2. Remove door grip cap and remove bolts of door grip portion.
3. Insert screw driver rolled with cloth between panel on vehicle and clips (as indicated with arrow), and remove finisher.
4. Pull up door finisher, and remove electrical parts connectors.
PIIA4947E
1. Door finisher (front) 2. Clip (C101) 3. Bolt
4. Door grip cap 5. Door finisher cap 6. Door finisher (rear)
SIIA0810E

DOOR FINISHER EI-35
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
5. Remove lock knob cable, inside handle cable and illumination
harness connector (front door only) from backside of inside han-
dle assembly.
6. Remove inside handle screws, and remove it from finisher.
Installation
Install in the reverse order of removal.
CAUTION:
To install finisher, check if all clips are matched over holes of panel on vehicle, then push it.
PIIA4959E

EI-36
BODY SIDE TRIM
Revision: 2005 July 2005 FX
BODY SIDE TRIMPFP:76913
Removal and InstallationAIS0037N
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
CENTER PILLAR LOWER GARNISH
Removal
1. Remove front and rear kicking plate.
2. Remove front and rear body side welt.
1. Front pillar garnish 2. Front body side welt 3. Dash side finisher
4. Nut 5. Front kicking plate 6. Center pillar lower garnish
7. Center pillar upper garnish 8. Bolt 9. Center pillar upper cap
10. Rear body side welt 11. Rear kicking plate 12. Clip (C203)
13. Center mudguard finisher (rear) 14. Center mudguard finisher (front)
PIIA4340E
PIIA4344E

BODY SIDE TRIM EI-37
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
3. Remove center pillar lower garnish.
NOTE:
Insert screwdriver rolled with cloth between panel on vehicle and
clips, then disconnect clips.
Installation
Install in the reverse order of removal.
NOTE:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
CENTER PILLAR UPPER GARNISH
Removal
1. Remove seat belt shoulder anchor. Refer to SB-3, "Removal and Installation of Front Seat Belt" .
2. Remove front and rear kicking plate.
3. Remove front and rear body side welt.
4. Remove center pillar lower garnish.
5. Remove center pillar upper cap and bolt.
6. Remove center pillar upper garnish.
Installation
Install in the reverse order of removal.
DASH SIDE FINISHER
Removal
1. Remove front kicking plate.
2. Remove front body side welt.
3. Remove nut.
4. Remove dash side finisher.
NOTE:
Insert screwdriver rolled with cloth between panel on vehicle and
clips, then disconnect clips.
Installation
Install in the reverse order of removal.
NOTE:
To install, check if all clips are matched over holes of panel on vehicle, then push on.
PIIA4341E
PIIA4342E
PIIA4343E

EI-38
BODY SIDE TRIM
Revision: 2005 July 2005 FX
FRONT PILLAR GARNISH
Removal
Remove front pillar garnish clips and remove front pillar garnish.
Installation
Install in the reverse order of removal.
KICKING PLATE
Removal
Remove kicking plate clips and remove kicking plate.
Installation
Install in the reverse order of removal.
CENTER MUDGUARD FINISHER (FRONT/REAR)
Removal
1. Remove center mudguard finisher (front).
2. Remove center mudguard finisher clip and remove center mud- guard finisher (rear).
Installation
Install in the reverse order of removal.
PIIA4345E
PIIA4346E

FLOOR TRIM EI-39
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
FLOOR TRIMPFP:74902
Removal and InstallationAIS0037O
REMOVAL
1. Remove front seat and rear seat cushion. Refer to SE-100, "Removal and Installation" and SE-106,
"Removal and Installation" .
2. Remove center console assembly. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
3. Remove front and rear kicking plate. Refer to EI-36, "
Removal and Installation" .
4. Remove front and rear body side welt. Refer to EI-36, "
Removal and Installation" .
5. Remove center pillar lower garnish. Refer to EI-36, "
Removal and Installation" .
6. Remove footrest screw, cover and foot-rest.
7. Remove dash side finisher. Refer to EI-36, "
Removal and Instal-
lation" .
8. Remove foot-grille (RH/LH).
9. Remove NAVI control unit. Refer to AV- 1 8 0 , "
Removal and
Installation of NAVI Control Unit" .
10. Remove carpet hook.
PIIA4956E
1. Floor carpet 2. Carpet hook 3. Nut
4. Foot-grille (RH) 5. Foot-grille (LH) 6. Foot-rest (driver)
7. Fixing clip 8. NAVI control unit
PIIA4957E

EI-40
FLOOR TRIM
Revision: 2005 July 2005 FX
11. Remove floor carpet from carpet fixing clip and remove floor car-
pet.
INSTALLATION
Install in the reverse order of removal.
PIIA1223E

HEADLINING EI-41
C
D E
F
G H
J
K L
M A
B
EI
Revision: 2005 July 2005 FX
HEADLININGPFP:73910
Removal and InstallationAIS0037P
PIIB3263E