engine INFINITI FX35 2005 Service Manual

DI-34
UNIFIED METER AND A/C AMP
Revision: 2005 July 2005 FX
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
*: Monitor keeps indicating “OFF” when brake warning lamp is on by the parking brake operation or low brake
fluid level.
DTC [U1000] CAN Communication CircuitAKS00CM7
Symptom: Display CAN COMM CIRC [U1000] at the result of self-diagnosis for unified meter and A/C amp.
1. CHECK CAN COMMUNICATION
1. Select “SELF-DIAG RESULTS” mode for “METER A/C AMP” with CONSULT-II.
2. Print out CONSULT-II screen.
>> Go to “CAN system”. Refer to LAN-5, "
Precautions When Using CONSULT-II" .
DTC [B2202] Meter Communication CircuitAKS00CM8
Symptom: Display METER COMM CIRC [B2202] at the result of self-diagnosis for unified meter and A/C amp.
1. CHECK CONNECTOR
Check combination meter, unified meter and A/C amp. and terminals (combination meter side, unified meter
and A/C amp. side, and harness side) for looseness or bent terminals.
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
2. CHECK METER/GAUGES VISUALLY
Check the pointer on the meter/gauge fluctuate at the engine start.
Is the fluctuation acceptable?
YES >> GO TO 3.
NO >> GO TO 6.
BRAKE SW [ON/OFF] X Indicates [ON/OFF] condition of brake switch (stop lamp switch).
AT-M IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T manual mode indicator.
AT-M GEAR [5-1] X X Indicates [5-1] condition of A/T manual mode gear position.
P RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift P range indicator.
R RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift R range indicator.
N RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift N range indicator.
D RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift D range indicator.
AT CHECK W/L X Indicates [ON/OFF] condition of AT CHECK warning lamp.
CRUISE IND [ON/OFF] X Indicates [ON/OFF] condition of CRUISE indicator lamp.
SET IND [ON/OFF] X Indicates [ON/OFF] condition of SET indicator lamp.
CRUISE W/L [ON/OFF] X Indicates [ON/OFF] condition of ICC warning lamp.
4WD LOCK SW [ON/OFF] X Indicates [ON/OFF] condition of snow mode switch.
4WD LOCK IND [ON/OFF] X Indicates [ON/OFF] condition of SNOW indicator lamp.
4WD W/L [ON/OFF] X Indicates [ON/OFF] condition of AWD warning lamp. Display item [Unit]
MAIN
SIGNALS SELECTION
FROM MENU Contents

WARNING LAMPS DI-51
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2005 July 2005 FX
Oil Pressure Warning Lamp Stays Off (Ignition Switch ON)AKS005NF
1. CHECK SELF-DIAGNOSTIC RESULTS OF UNIFIED METER AND A/C AMP.
Select “METER A/C AMP” on CONSULT-II, and perform self-diagnosis of unified meter and A/C amp. Refer to
DI-31, "
CONSULT-II Function (METER A/C AMP)" .
Self-diagnostic results content
No malfunction detected>> GO TO 2.
Malfunction detected>> Go to DI-17, "
Symptom Chart 2" in “COMBINATION METER”.
2. CHECK IPDM E/R OUTPUT SIGNAL
Activate IPDM E/R auto active test. Refer to PG-24, "
Auto Active Test" .
Does oil pressure warning lamp is blinking?
YES >> GO TO 5.
NO >> GO TO 3.
3. CHECK BCM INPUT SIGNAL
Select “DATA MONITOR” of “SIGNAL BUFFER”. Refer to BCS-13,
"CONSULT-II Function (BCM)" . Operate ignition switch with “OIL
PRESS SW” of “DATA MONITOR” and check operate status.
OK or NG
OK >> GO TO 4.
NG >> Replace IPDM E/R. Refer to PG-30, "
Removal and
Installation of IPDM E/R" .
4. CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL
Select “METER A/C AMP” on CONSULT-II. Operate ignition switch
with “OIL W/L” of “DATA MONITOR” and check operation status.
OK or NG
OK >> Replace combination meter.
NG >> Replace BCM. Refer to BCS-16, "
Removal and Installa-
tion of BCM" .
“OIL PRESS SW”
When ignition switch is in ON
position (Engine stopped) : ON
When engine running : OFF
SKIA8709E
“OIL W/L”
When ignition switch is in ON
position (Engine stopped) : ON
When engine running : OFF
PKIA2064E

WARNING LAMPS DI-53
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2005 July 2005 FX
3. CHECK OIL PRESSURE SWITCH CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector E9 ter- minal 57 (BR) and ground.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-30, "Removal and
Installation of IPDM E/R" .
NG >> Repair harness or connector.
Component InspectionAKS005NH
OIL PRESSURE SWITCH
Check continuity between oil pressure switch and ground. 57 (BR) – Ground : Continuity should not exist.
SKIA5013E
Condition
Oil pressure kPa (kg/cm2 , psi) Continuity
Engine stopped Less than 29 (0.3, 4) Yes Engine running More than 29 (0.3, 4) No
ELF0044D

DI-56
A/T INDICATOR
Revision: 2005 July 2005 FX
A/T Indicator Is MalfunctionAKS005NJ
1. CHECK SELF-DIAGNOSIS OF COMBINATION METER
Perform combination meter self-diagnosis. Refer to DI-14, "
OPERA-
TION PROCEDURE" .
Are all segments displayed?
YES >> GO TO 2.
NO >> Replace combination meter.
2. CHECK SELF-DIAGNOSIS RESULTS OF UNIFIED METER AND A/C AMP.
Select “METER A/C AMP” on CONSULT-II, and perform self-diagnosis of unified meter and A/C amp. Refer to
DI-31, "
CONSULT-II Function (METER A/C AMP)" .
Self-diagnostic results content
No malfunction detected>> GO TO 3.
Malfunction detected>> Go to DI-17, "
Symptom Chart 2" in “COMBINATION METER”.
3. CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL
1. Connect CONSULT-II and start engine.
2. Use “DATA MONITOR” of “METER A/C AMP” on CONSULT-II. Confirm each indication on the monitor when operating the shift
lever.
OK or NG
OK >> Replace combination meter.
NG >> GO TO 4.
4. CHECK A/T DEVICE
Perform A/T device inspection. Refer to AT- 1 7 0 , "
DTC P1815 MANUAL MODE SWITCH" .
OK or NG
OK >> GO TO 5.
NG >> Repair or replace applicable parts.
EL-3828D
CONSULT-II display Switch operation Operation
status
AT - M I N D Manual mode range ON
Except for manual mode range OFF
AT - M G E A R Manual mode range (shift- up or down) 5 - 1
Except for manual mode range 1
P RANGE IND P range position ON
Except for P range position OFF
R RANGE IND R range position ON
Except for R range position OFF
N RANGE IND N range position ON
Except for N range position OFF
D RANGE IND D range position ON
Except for D range position OFF
SKIA6259E

DI-86
LANE DEPARTURE WARNING SYSTEM
Revision: 2005 July 2005 FX
Camera Aiming AdjustmentAKS00C7J
OUTLINE
Adjust the camera aiming every time the LDW camera unit is removed or installed.
CAUTION:

Place the vehicle on the level ground when the camera aiming adjustment is operated.

Follow the CONSULT-II when adjusting the camera aiming. (Camera aiming adjustment cannot be
operated without CONSULT-II.)
PREPARATION

Keep all tires inflated to correct pressures. Adjust the tire pressure to the specified pressure value.

There is no-load in vehicle. Check if coolant, engine oil are filled up to correct level and fuel tank is full.

Shift the gear into “P” position and release the parking brake.

Clean the windshield.
NOTE:
Do not place anything reflective on the upper surface of instrument panel.
TARGET SETTING
Preparation Aiming Adjustment Jig
For aiming adjustment, prepare the following jigs and targets.
PKIB4693E

LANE DEPARTURE WARNING SYSTEM DI-89
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2005 July 2005 FX
7. Mark point at the center of the point “E” and “F”, on the line
“FW”.
CAUTION:
Make sure that “E” through “X” is equal to “F” through “X”.
8. Position the center of the right target to the point of “X”.
VEHICLE HEIGHT CHECK
Measure the wheel arch height. And calculate “Dh”.
NOTE:
“Dh” may be calculated as a minus value.
AIMING ADJUSTMENT
Operation Procedure
CAUTION:

Perform the adjustment under unloaded vehicle condition.

LDW indicator is turned off after the removal/installation, and blinks after replacement.
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER on the data link connector.
3. Start the engine, wait for at least 10 seconds, and touch “START (NISSAN BASED VHCL)”.
PKIB5331E
Dh [mm] = (Hfl + Hfr) ÷ 2 − 840
where, Hfl: Front left wheel arch height [mm]
Hfr: Front right wheel arch height [mm]
SKIB3164E
PBIB1503E
SAIA0450E

REAR VIEW MONITOR DI-123
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2005 July 2005 FX
Side Distance Guideline CorrectionAKS0068L
This mode is used to modify the side distance guidelines if they are dislocated from the rear view monitor
image, because of variations of body/camera mounting conditions.
SIDE DISTANCE GUIDELINE CORRECTION PROCEDURE
1. Create a correction line to modify the screen.
Draw lines on the rearward of the vehicle passing through the
following points: 0.2 m (7.87 in) from both sides of the vehicle,
and

*1: 0.5 m (1.5 feet)

*2: 1 m (3 feet)

*3: 2 m (7 feet)

*4: 3 m (10 feet)
and from the rear end of the bumper
2. With the ignition switch OFF, connect “CONSULT-II” and “CON- SULT-II CONVERTER” to the data link connector, then turn igni-
tion switch ON. Touch “REARVIEW CAMERA” on CONSULT-II.
CAUTION:
Stop engine for the safety when correcting side distance
guideline.
3. Shift A/T selector lever to R position.
4. Touch “SELCT GUIDELINE PATTERN” on “SELECT WORK ITEM” screen.
SKIA5637E
SKIA6103E
SKIA5638E

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D E
F
G H
I
J
K L
M
SECTION EC
A
EC
Revision: 2005 July 2005 FX
ENGINE CONTROL SYSTEM
VQ35DE
INDEX FOR DTC ...................................................... 15
DTC No. Index .................................................... ... 15
Alphabetical Index ............................................... ... 19
PRECAUTIONS ..................................................... ... 23
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ... 23
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... ... 23
Precaution ........................................................... ... 23
PREPARATION ...................................................... ... 27
Special Service Tools .......................................... ... 27
Commercial Service Tools ................................... ... 29
ENGINE CONTROL SYSTEM ............................... ... 30
System Diagram .................................................. ... 30
Multiport Fuel Injection (MFI) System ................. ... 31
Electronic Ignition (EI) System ............................ ... 33
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. ... 34
AIR CONDITIONING CUT CONTROL .................. ... 35
Input/Output Signal Chart .................................... ... 35
System Description ............................................. ... 35
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 36
System Description ............................................. ... 36
Component Description ....................................... ... 37
CAN COMMUNICATION ....................................... ... 38
System Description ............................................. ... 38
EVAPORATIVE EMISSION SYSTEM .................... ... 39
Description .......................................................... ... 39
Component Inspection ........................................ ... 42
Removal and Installation ..................................... ... 43
How to Detect Fuel Vapor Leakage .................... ... 43
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... ... 46
System Description ............................................. ... 46
Diagnostic Procedure .......................................... ... 47
Component Inspection ........................................ ... 49 POSITIVE CRANKCASE VENTILATION ..............
... 51
Description ........................................................... ... 51
Component Inspection ......................................... ... 51
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... ... 53
Description ........................................................... ... 53
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 54
Introduction .......................................................... ... 54
Two Trip Detection Logic ..................................... ... 54
Emission-Related Diagnostic Information ............ ... 55
Malfunction Indicator Lamp (MIL) ........................ ... 69
OBD System Operation Chart ............................. ... 72
BASIC SERVICE PROCEDURE ............................ ... 78
Basic Inspection .................................................. ... 78
Idle Speed and Ignition Timing Check ................. ... 83
Idle Mixture Ratio Adjustment .............................. ... 85
VIN Registration .................................................. ... 96
Accelerator Pedal Released Position Learning ... ... 96
Throttle Valve Closed Position Learning .............. ... 96
Idle Air Volume Learning ..................................... ... 97
Fuel Pressure Check ........................................... ... 99
TROUBLE DIAGNOSIS ......................................... .101
Trouble Diagnosis Introduction ............................ .101
DTC Inspection Priority Chart .............................. .107
Fail-Safe Chart .................................................... .109
Symptom Matrix Chart ......................................... .110
Engine Control Component Parts Location ......... .114
Vacuum Hose Drawing ........................................ .120
Circuit Diagram .................................................... .121
ECM Harness Connector Terminal Layout .......... .123
ECM Terminals and Reference Value .................. .123
CONSULT-II Function (ENGINE) ......................... .132
Generic Scan Tool (GST) Function ...................... .144
CONSULT-II Reference Value in Data Monitor .... .147
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .151
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .153
Description ........................................................... .153
Testing Condition ................................................. .153

EC-5
C
D E
F
G H
I
J
K L
M
EC A
Revision: 2005 July 2005 FX
FUNCTION .............................................................
. 426
Description .......................................................... . 426
On Board Diagnosis Logic .................................. . 426
DTC Confirmation Procedure .............................. . 426
Wiring Diagram ................................................... . 427
Diagnostic Procedure .......................................... . 428
Component Inspection ........................................ . 431
Remove and Installation ...................................... . 431
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY ................................................................... . 432
Component Description ....................................... . 432
CONSULT-II Reference Value in Data Monitor Mode . 432
On Board Diagnosis Logic .................................. . 432
DTC Confirmation Procedure .............................. . 432
Wiring Diagram ................................................... . 434
Diagnostic Procedure .......................................... . 435
DTC P1128 THROTTLE CONTROL MOTOR ....... . 437
Component Description ....................................... . 437
On Board Diagnosis Logic .................................. . 437
DTC Confirmation Procedure .............................. . 437
Wiring Diagram ................................................... . 438
Diagnostic Procedure .......................................... . 439
Component Inspection ........................................ . 440
Removal and Installation ..................................... . 441
DTC P1146, P1166 HO2S2 .................................... . 442
Component Description ....................................... . 442
CONSULT-II Reference Value in Data Monitor Mode . 442
On Board Diagnosis Logic .................................. . 442
DTC Confirmation Procedure .............................. . 443
Overall Function Check ....................................... . 443
Wiring Diagram ................................................... . 445
Diagnostic Procedure .......................................... . 448
Component Inspection ........................................ . 450
Removal and Installation ..................................... . 452
DTC P1147, P1167 HO2S2 .................................... . 453
Component Description ....................................... . 453
CONSULT-II Reference Value in Data Monitor Mode . 453
On Board Diagnosis Logic .................................. . 453
DTC Confirmation Procedure .............................. . 454
Overall Function Check ....................................... . 454
Wiring Diagram ................................................... . 456
Diagnostic Procedure .......................................... . 459
Component Inspection ........................................ . 461
Removal and Installation ..................................... . 463
DTC P1148, P1168 CLOSED LOOP CONTROL ... . 464
On Board Diagnosis Logic .................................. . 464
DTC P1211 TCS CONTROL UNIT ........................ . 465
Description .......................................................... . 465
On Board Diagnosis Logic .................................. . 465
DTC Confirmation Procedure .............................. . 465
Diagnostic Procedure .......................................... . 465
DTC P1212 TCS COMMUNICATION LINE ........... . 466
Description .......................................................... . 466
On Board Diagnosis Logic .................................. . 466
DTC Confirmation Procedure .............................. . 466
Diagnostic Procedure .......................................... . 466 DTC P1217 ENGINE OVER TEMPERATURE .......
.467
Description ........................................................... .467
CONSULT-II Reference Value in Data Monitor Mode .469
On Board Diagnosis Logic ................................... .469
Overall Function Check ....................................... .469
Wiring Diagram .................................................... .471
Diagnostic Procedure .......................................... .473
Main 12 Causes of Overheating .......................... .478
Component Inspection ......................................... .478
DTC P1225 TP SENSOR ....................................... .479
Component Description ....................................... .479
On Board Diagnosis Logic ................................... .479
DTC Confirmation Procedure .............................. .479
Diagnostic Procedure .......................................... .480
Removal and Installation ..................................... .480
DTC P1226 TP SENSOR ....................................... .481
Component Description ....................................... .481
On Board Diagnosis Logic ................................... .481
DTC Confirmation Procedure .............................. .481
Diagnostic Procedure .......................................... .482
Removal and Installation ..................................... .482
DTC P1229 SENSOR POWER SUPPLY ............... .483
On Board Diagnosis Logic ................................... .483
DTC Confirmation Procedure .............................. .483
Wiring Diagram .................................................... .484
Diagnostic Procedure .......................................... .485
DTC P1271, P1281 A/F SENSOR 1 ...................... .488
Component Description ....................................... .488
CONSULT-II Reference Value in Data Monitor Mode .488
On Board Diagnosis Logic ................................... .488
DTC Confirmation Procedure .............................. .488
Wiring Diagram .................................................... .490
Diagnostic Procedure .......................................... .493
Removal and Installation ..................................... .496
DTC P1272, P1282 A/F SENSOR 1 ...................... .497
Component Description ....................................... .497
CONSULT-II Reference Value in Data Monitor Mode .497
On Board Diagnosis Logic ................................... .497
DTC Confirmation Procedure .............................. .497
Wiring Diagram .................................................... .499
Diagnostic Procedure .......................................... .502
Removal and Installation ..................................... .505
DTC P1273, P1283 A/F SENSOR 1 ...................... .506
Component Description ....................................... .506
CONSULT-II Reference Value in Data Monitor Mode .506
On Board Diagnosis Logic ................................... .506
DTC Confirmation Procedure .............................. .506
Wiring Diagram .................................................... .508
Diagnostic Procedure .......................................... .511
Removal and Installation ..................................... .515
DTC P1274, P1284 A/F SENSOR 1 ...................... .516
Component Description ....................................... .516
CONSULT-II Reference Value in Data Monitor Mode .516
On Board Diagnosis Logic ................................... .516

EC-7
C
D E
F
G H
I
J
K L
M
EC A
Revision: 2005 July 2005 FX
Wiring Diagram ...................................................
. 615
Diagnostic Procedure .......................................... . 616
Component Inspection ........................................ . 618
DTC P2122, P2123 APP SENSOR ....................... . 619
Component Description ....................................... . 619
CONSULT-II Reference Value in Data Monitor Mode . 619
On Board Diagnosis Logic .................................. . 619
DTC Confirmation Procedure .............................. . 620
Wiring Diagram ................................................... . 621
Diagnostic Procedure .......................................... . 622
Component Inspection ........................................ . 624
Removal and Installation ..................................... . 625
DTC P2127, P2128 APP SENSOR ....................... . 626
Component Description ....................................... . 626
CONSULT-II Reference Value in Data Monitor Mode . 626
On Board Diagnosis Logic .................................. . 626
DTC Confirmation Procedure .............................. . 627
Wiring Diagram ................................................... . 628
Diagnostic Procedure .......................................... . 629
Component Inspection ........................................ . 632
Removal and Installation ..................................... . 632
DTC P2135 TP SENSOR ....................................... . 633
Component Description ....................................... . 633
CONSULT-II Reference Value in Data Monitor Mode . 633
On Board Diagnosis Logic .................................. . 633
DTC Confirmation Procedure .............................. . 634
Wiring Diagram ................................................... . 635
Diagnostic Procedure .......................................... . 636
Component Inspection ........................................ . 639
Removal and Installation ..................................... . 639
DTC P2138 APP SENSOR .................................... . 640
Component Description ....................................... . 640
CONSULT-II Reference Value in Data Monitor Mode . 640
On Board Diagnosis Logic .................................. . 640
DTC Confirmation Procedure .............................. . 641
Wiring Diagram ................................................... . 642
Diagnostic Procedure .......................................... . 643
Component Inspection ........................................ . 647
Removal and Installation ..................................... . 647
IGNITION SIGNAL ................................................. . 648
Component Description ....................................... . 648
Wiring Diagram ................................................... . 649
Diagnostic Procedure .......................................... . 654
Component Inspection ........................................ . 659
Removal and Installation ..................................... . 660
INJECTOR CIRCUIT .............................................. . 661
Component Description ....................................... . 661
CONSULT-II Reference Value in Data Monitor Mode . 661
Wiring Diagram ................................................... . 662
Diagnostic Procedure .......................................... . 663
Component Inspection ........................................ . 667
Removal and Installation ..................................... . 667
FUEL PUMP CIRCUIT ........................................... . 668
Description .......................................................... . 668 CONSULT-II Reference Value in Data Monitor Mode
.668
Wiring Diagram .................................................... .669
Diagnostic Procedure .......................................... .670
Component Inspection ......................................... .672
Removal and Installation ..................................... .673
REFRIGERANT PRESSURE SENSOR ................. .674
Component Description ....................................... .674
Wiring Diagram .................................................... .675
Diagnostic Procedure .......................................... .676
Removal and Installation ..................................... .678
ELECTRICAL LOAD SIGNAL ............................... .679
Description ........................................................... .679
CONSULT-II Reference Value in Data Monitor Mode .679
Diagnostic Procedure .......................................... .679
ICC BRAKE SWITCH ............................................ .680
Component Description ....................................... .680
CONSULT-II Reference Value in Data Monitor Mode .680
Wiring Diagram .................................................... .681
Diagnostic Procedure .......................................... .682
Component Inspection ......................................... .687
ASCD BRAKE SWITCH ........................................ .688
Component Description ....................................... .688
CONSULT-II Reference Value in Data Monitor Mode .688
Wiring Diagram .................................................... .689
Diagnostic Procedure .......................................... .690
Component Inspection ......................................... .694
ASCD INDICATOR ................................................. .695
Component Description ....................................... .695
CONSULT-II Reference Value in Data Monitor Mode .695
Wiring Diagram .................................................... .696
Diagnostic Procedure .......................................... .697
SNOW MODE SWITCH ......................................... .698
Description ........................................................... .698
CONSULT-II Reference Value in the Data Monitor
Mode .................................................................... .698
Wiring Diagram .................................................... .699
Diagnostic Procedure .......................................... .700
Component Inspection ......................................... .702
MIL AND DATA LINK CONNECTOR ..................... .703
Wiring Diagram .................................................... .703
SERVICE DATA AND SPECIFICATIONS (SDS) ... .705
Fuel Pressure ...................................................... .705
Idle Speed and Ignition Timing ............................ .705
Calculated Load Value ......................................... .705
Mass Air Flow Sensor .......................................... .705
Intake Air Temperature Sensor ............................ .705
Engine Coolant Temperature Sensor .................. .705
Air Fuel Ratio (A/F) Sensor 1 Heater ................... .705
Heated Oxygen sensor 2 Heater ......................... .705
Crankshaft Position Sensor (POS) ...................... .705
Camshaft Position Sensor (PHASE) ................... .705
Throttle Control Motor .......................................... .705
Injector ................................................................. .706
Fuel Pump ........................................................... .706