display INFINITI FX35 2005 Service Manual

REAR WINDOW DEFOGGER GW-87
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2005 July 2005 FX

to rear window defogger relay terminal 1,

through 15A fuse [No. 32, located in the fuse block (J/B)]

to A/C and AV switch terminal 1,

through 50A fusible link (letter M , located in the fuse and fusible link box)

to BCM terminal 55,

through 15A fuse [No. 22, located in the fuse block (J/B)]

to BCM terminal 42.
With the ignition switch turned to ON or START position,
Power is supplied

through 15A fuse [No. 1, located in the fuse block (J/B)]

to BCM terminal 38.
Ground is supplied

to BCM terminal 49 and 52

through body grounds M35, M45 and M85,

to A/C and AV switch terminal 5

through body grounds M35, M45 and M85,

to IPDM E/R terminals 38 and 60

through body grounds E21, E50 and E51.
When rear window defogger switch in A/C and AV switch is turned to ON,
Ground is supplied

to BCM terminal 9

through A/C and AV switch terminal 16

through A/C and AV switch terminal 5 and

through body grounds M35, M45 and M85.
Then rear window defogger switch is illuminated.
Then BCM recognizes that rear window defogger switch is turned to ON.
Then it sends rear window defogger switch signals to IPDM E/R, display control unit (with navigation system)
or display unit (without navigation system) via DATA LINE (CAN H, CAN L).
When display control unit (with navigation system) or display unit (without navigation system) receives rear
window defogger switch signals, and display on the screen.
When IPDM E/R receives rear window defogger switch signals,
Ground is supplied

to rear window defogger relay terminal 2

through IPDM E/R terminal 52

through IPDM E/R terminals 38 and 60 and

through body grounds E21, E50 and E51.
And then rear window defogger relay is energized.
When rear window defogger relay is turned ON, signals are transmitted.

through rear window defogger relay terminals 5 and 7

to rear window defogger terminal 1
Rear window defogger terminal 2 is grounded through grounds B15 and B45.
With power and ground supplied, rear window defogger filaments heat and defog the rear window.
When rear window defogger relay is turned to ON,
Power is supplied

through rear window defogger relay terminal 7

through fuse block (J/B) terminal 2C

through 15A fuse [No. 8, located in the fuse block (J/B)] and

through fuse block (J/B) terminal 5B

to door mirror defogger (driver side and passenger side) terminal 1.
Door mirror defogger (driver side and passenger side) terminal 2 is grounded through body grounds M35, M45
and M85.

REAR WINDOW DEFOGGER GW-95
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2005 July 2005 FX
CONSULT-II Function (BCM)AIS004R7
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
1. Turn ignition switch “OFF”.
2. Connect “CONSULT-II” and CONSULT-II CONVERTER to data link connector.
3. Turn ignition switch “ON”.
4. Touch “START (NISSAN BASED VHCL)”.
5. Touch “BCM”. If “BCM” is not indicated, go to GI-39
, “CONSULT-II Date Link
Connector (DLC) Circuit”
6. Touch “REAR DEFOGGER”.
BCM diagnostic test item Check item diagnostic test mode Content REAR DEFOGGER Data monitor Displays the input data of BCM in real time.
Active test Gives a drive signal to a load to check the operation.
PBIB1503E
BCIA0029E
BCIA0030E
LIIA0153E

GW-96
REAR WINDOW DEFOGGER
Revision: 2005 July 2005 FX
7. Select diagnosis mode,“DATA MONITOR” and “ACTIVE TEST”
are available.
DATA MONITOR
Display Item List
ACTIVE TEST
Display Item List
BCIA0031E
Monitor item Content
REAR DEF SW Displays “Press (ON)/others (OFF)” status determined with the rear window defogger switch.
IGN ON SW Displays “IGN (ON)/OFF” status determined with the ignition switch signal.
Test item Content
REAR DEFOGGER Gives a drive signal to the rear window defogger relay to activate it.

REAR WINDOW DEFOGGER GW-97
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2005 July 2005 FX
Work FlowAIS004R6
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to GW-86, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to GW-97,
"Trouble Diagnoses Symptom Chart" .
4. Does rear window defogger operate normally? YES: GO TO 5, NO: GO TO 3.
5. INSPECTION END.
Trouble Diagnoses Symptom ChartAIS004R8
Make sure other systems using the signal of the following systems operate normally.
Symptom Diagnoses / Service procedure Refer to page
Rear window defogger and door mirror defogger do not
operate. 1. BCM power supply and ground circuit check.
GW-98
2. IPDM E/R auto active test check PG-24
3. Rear window defogger switch circuit checkGW-99
4. Rear window defogger power supply circuit checkGW-100
5. Replace IPDM E/ R PG-30
Rear window defogger does not operate but both of door
mirror defogger operate. 1. Rear window defogger circuit check
GW-102
2. Filament checkGW-108
Door mirror defogger does not operated but both of rear
window defogger operate. 1. Door mirror defogger power supply circuit check
GW-103
Driver side door mirror defogger does not operate. 1. Driver side door mirror defogger circuit check GW-105
Passenger side door mirror defogger does not operate. 1. Passenger side door mirror defogger circuit checkGW-106
Rear window defogger switch does not light, and rear win-
dow defogger is not displayed on the display.
But rear window defogger operates. 1. Rear window defogger signal check
GW-106

REAR WINDOW DEFOGGER GW-107
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2005 July 2005 FX
2. CHECK AV COMMUNICATION LINE
AV communication line check is performed. Refer to AV- 8 4 , "
AV Communication Line Inspection"
Is rear window defogger displayed on the display?
YES >> GO TO 3.
NO >> Replace display control unit.
3. CHECK CAN COMMUNICATION LINE
CAN communication line check is performed. Refer to AV- 8 5 , "
CAN Communication Line Inspection"
OK or NG
OK >> Check condition of harness and connector.
NG >> In addition, it is necessary to check CAN communication line. Refer to AV- 8 5 , "
CAN Communica-
tion Line Inspection"

IDX-3
A
C
D E
F
G H
I
J
K L
B
IDX
ALPHABETICAL INDEX
BRK/SW - Wiring diagram ...............
EC-615, EC-1298
Bulb specifications ............................................ LT-203
Bumper, front ....................................................... EI-14
Bumper, rear ........................................................ EI-17
C
Camshaft inspection(VK45DE) ........................ EM-213
Camshaft inspection(VQ35DE) ......................... EM-86
Camshaft position sensor (PHASE) EC-307, EC-1043
Camshaft(VK45DE) ......................................... EM-212
Camshaft(VQ35DE) ........................................... EM-84
CAN .................................................................... DI-29
CAN - Wiring diagram ......... EC-172, EC-863, LAN-49,
LAN-87
, LAN-128, LAN-173, LAN-221, LAN-262,
LAN-306
, LAN-353, LAN-402, LAN-436
CAN (Controller Area Network) . BL-24, BL-59, BL-98,
BL-191
, GW-22, GW-88, RF-13, SE-16
CAN communication EC-171, EC-862, AT-32, AT-106,
TF-13
, TF-32, WT-9, BRC-11, BL-24, BL-59, BL-98,
BL-191
, GW-22, GW-88, RF-13, SE-16, DI-84, WW-9
Canister-See EVAP canister ............... EC-42, EC-733
Center bearing assembly (propeller shaft) ........ PR-13
Center bearing disassembly (propeller shaft) .... PR-12
CHARGE - Wiring diagram ................................ SC-24
Charging system ................................................ SC-23
Chassis and body maintenance ........................ MA-29
CHIME - Wiring diagram ..................................... DI-63
CIGAR - Wiring diagram .................................. WW-55
Cigarette lighter ............................................... WW-55
Cigarette lighter illumination ............................. LT-158
Circuit breaker ................................................... PG-17
Clock ................................................................. DI-112
CLOCK - Wiring diagram .................................. DI-112
Closed loop control .............................. EC-32, EC-723
Collision diagnosis ........................................... SRS-46
Combination lamp, rear, removal and installation ........
LT-149
Combination meter ............................................... DI-5
Combination meter removal and installation - See
Instrument panel .................................................. IP-11
COMM - Wiring diagram .................................. AV-114
COMPAS - Wiring diagram ................................. DI-40
Compass ............................................................ DI-38
Component Location (auto A/C) ...................... ATC-43
Compression pressure(VK45DE) .................... EM-229
Compression pressure(VQ35DE) .................... EM-100
Compressor clutch removal and installation .. ATC-144
Compressor special service tool ...................... ATC-17
Condenser ..................................................... ATC-155
Connecting rod bearing clearance(VK45DE) .. EM-269
Connecting rod bushing clearance .................. EM-142
Connecting rod bushing clearance(VK45DE) .. EM-264
Connecting rod(VK45DE) ................................ EM-264
Connecting rod(VQ35DE) ................................ EM-140
Console box - See Instrument panel ................... IP-10
CONSULT for VDC ......................................... BRC-25
CONSULT-II Reference value (A/T) .................. AT-90
Control units (terminal arrangement) ................. PG-76
Control valve (A/T) ............................................. AT-37
Controller Area Network (CAN) . BL-24, BL-59, BL-98,
BL-191
, GW-22, GW-88, RF-13, SE-16
Converter housing installation ........... AT-272, AT-276
COOL/F - Wiring diagram ................ EC-471, EC-1217
Coolant replacement(VQ35DE) ........................ MA-15
Cooling circuit (engine)(VK45DE) ..................... CO-35
Cooling circuit (engine)(VQ35DE) ...................... CO-9
Cooling fan motor ............................ EC-478, EC-1224
Cooling fan(VK45DE) ....................................... CO-49
Cooling fan(VQ35DE) ....................................... CO-21
Cowl top .............................................................. EI-23
Cowl top cover .................................................... EI-23
Crankcase ventilation system - See Positive crankcase
ventilation ............................................. EC-51
, EC-742
Crankshaft position sensor (POS) ... EC-300, EC-1036
Crankshaft(VK45DE) ...................................... EM-246
Crankshaft(VQ35DE) ...................................... EM-140
Crash zone sensor .......................................... SRS-42
Cylinder block boring(VK45DE) ...................... EM-267
Cylinder block(VK45DE) ................................. EM-245
Cylinder block(VQ35DE) ................................. EM-122
Cylinder head bolt tightening(VK45DE) .......... EM-231
Cylinder head bolt tightening(VQ35DE) .......... EM-103
Cylinder head(VK45DE) ................................. EM-229
Cylinder head(VQ35DE) ................................. EM-100
D
D/LOCK - Wiring diagram ....................... BL-26
, BL-32
Daytime light system ........................................... LT-39
Daytime running light - See Daytime light system LT-39
Diagnosis sensor unit ..................................... SRS-45
Diagnostic trouble code (DTC) for OBD system EC-15,
EC-707
Direct clutch solenoid valve ............... AT-158, AT-160
Display and amp.assembly ............... ATC-51, ATC-63
Door glass ........................................... GW-76, GW-80
Door glass Fitting Adjustment(Front) ................ GW-78
Door glass Fitting Adjustment(Rear) ................. GW-83
Door lock .......................................................... BL-157
Door mirror ...................................................... GW-114
Door trim ............................................................. EI-34
Door, front ........................................... BL-153, GW-76
Door, rear ............................................ BL-153, GW-80
Drive belt inspection ......................................... MA-22
Drive belt inspection(VQ35DE) ......................... MA-14
Drive belt(VK45DE) ........................................ EM-173
Drive belt(VQ35DE) .......................................... EM-15
Drive shaft ......................................................... MA-38
Drive shaft (rear) ............................................... RAX-9
Driver air bag .................................................. SRS-35
DTRL - Wiring diagram ....................................... LT-42
Duct and grilles .............................................. ATC-134
E
ECM power supply EC-164
, EC-413, EC-855, EC-1137
ECM/PW - Wiring diagram ............... EC-414, EC-1138

INSTRUMENT PANEL ASSEMBLY IP-11
C
D E
F
G H
J
K L
M A
B
IP
Revision: 2005 July 2005 FX
Removal and InstallationAIS003CJ
WORK STEP
When removing instrument panel and pad, combination meter, display unit and audio unit, center console take
steps in the order shown by the numbers below.
CAUTION:

Disconnect both battery cables in advance.

Disconnect air bag system line in advance.

Never temper with air bag lid or force air bag lid to open, as this may adversely affect air bag per-
formance.

Be careful not to scratch pad and other parts.
1. Front defroster grille (RH) 2. Instrument panel and pad 3. Front defroster grille (LH)
4. Screw 5. Bolt 6. Combination meter assembly
7. Steering lock escutcheon 8. Side ventilation (LH) 9. Display unit and audio unit
10. Wiper and washer switch 11. Clip 12. Rubber
13. Lighting and turn signal switch 14. Combination meter bracket 15. Cluster lid C
16. Steering column upper cover 17. Steering column lower cover 18. Steering column front lower cover
19. Instrument side panel (LH) 20. Instrument clock finisher 21. A/T console finisher
22. Instrument driver lower panel 23. Console finisher (LH) 24. Center console
25. Console finisher (RH) 26. Instrument side panel (RH) 27. Instrument lower cover
28. Instrument passenger lower panel 29. Side ventilation (RH) 30. Front passenger air bag module mounting nut
Parts Reference
page Instrument
panel and pad Combination
meter Display unit and
audio unit Center console
(A) Front kicking plate (RH/LH) EI-38
[ 1 ] [ 1 ]
(B) Dash side finisher (RH/LH) EI-37
[ 2 ] [ 2 ]
(C) Front pillar garnish (RH/LH) EI-38
[ 3 ]
(D) A/T select lever knob AT- 2 3 3
[ 4 ] [ 1 ]
(E) Instrument clock finisher IP-12
[ 5 ] [ 2 ]
(F) A/T console finisher IP-12
[ 6 ] [ 3 ]
(G) Console finisher (RH/LH) IP-12
[ 7 ] [ 4 ]
(H) Center console IP-12
[ 8 ] [ 5 ]
(I) Instrument lower cover IP-13
[ 9 ]
(J) Instrument passenger lower panel IP-13
[10]
(K) Instrument driver lower panel IP-13
[11] [ 3 ]
(L) Steering column front lower cover IP-13
[12] [ 4 ]
(M) Steering column lower cover IP-13
[13] [ 5 ]
(N) Steering column upper cover IP-14
[14] [ 6 ]
(O) Wiper and washer switch IP-14
[15] [ 7 ]
(P) Lighting and turn signal switch IP-14
[16] [ 8 ]
(Q) Steering lock escutcheon IP-14
[17] [ 9 ]
(R) Combination meter assembly IP-14
[18] [10]
(S) Instrument side panel (RH/LH) IP-14
[19]
(T) Cluster lid C IP-15
[20] [ 1 ]
(U) Display unit and audio unit IP-15
[21] [ 2 ]
(V) Front defroster grille (RH/LH) IP-15
[22]
(W) Combination meter bracket IP-15
[23]
(X) Side ventilation (RH/LH) IP-16
[24]
(Y) Instrument panel and pad IP-16
[25]

INSTRUMENT PANEL ASSEMBLY IP-15
C
D E
F
G H
J
K L
M A
B
IP
Revision: 2005 July 2005 FX
(T) Cluster Lid C
1. Insert a remover into gap between instrument panel and pad,
pull back to your side, and disconnect metal clips below.
2. Disconnect harness connectors, and remove cluster lid C.
CAUTION:
Cover surroundings with cloth to avoid scratches or damages.
(U) Display Unit and Audio Unit
1. Remove screws with power tool.
2. Disconnect harness connector, and remove display unit and audio unit.
CAUTION:
Unit is heavy, so be careful not to pinch your fingers when
working.
(V) Front Defroster Grille (RH/LH)
Insert a remover into gaps between front defroster grille (RH/LH) and
instrument panel and pad, lift front defroster grille up, and remove
front defroster grille (RH/LH).
(W) Combination Meter Bracket
1. Remove bolts.
2. The installation bolts of the harness clip and steering column assembly is removed, steering column assembly is pulled back-
ward, and set combination meter bracket free from the instru-
ment panel and pad. Refer to PS-12, "
STEERING COLUMN" .
PIIA4994E
PIIB1335E
PIIA5009E
PIIA5010E

LAN-1
LAN SYSTEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION LAN
A
B
LAN
Revision: 2005 July 2005 FX
LAN SYSTEM
CAN
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 5
Precautions When Using CONSULT-II ................ ..... 5
CHECK POINTS FOR USING CONSULT-II .... ..... 5
Precautions For Trouble Diagnosis ..................... ..... 5
CAN SYSTEM .................................................. ..... 5
Precautions For Harness Repair ......................... ..... 6
CAN SYSTEM .................................................. ..... 6
TROUBLE DIAGNOSES WORK FLOW ............... ..... 7
When Displaying CAN Communication System
Errors .................................................................. ..... 7
WHEN A MALFUNCTION IS DETECTED BY
CAN COMMUNICATION SYSTEM .................. ..... 7
WHEN A MALFUNCTION IS DETECTED
EXCEPT CAN COMMUNICATION SYSTEM ... ..... 7
TROUBLE DIAGNOSIS FLOW CHART .......... ..... 8
Diagnosis Procedure ........................................... ..... 9
SELECTING CAN SYSTEM TYPE (HOW TO
USE SPECIFICATION TABLE) ........................ ..... 9
ACQUISITION OF DATA BY CONSULT-II ....... ... 10
HOW TO USE CHECK SHEET TABLE ........... .... 11
CAN Diagnostic Support Monitor ........................ ... 18
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR ECM ............................ ... 18
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR TCM ............................ ... 19
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR DISPLAY CONTROL
UNIT ................................................................. ... 20
DESCRIPTION OF “CAN DIAG MNTR” SCREEN
FOR DISPLAY UNIT ........................................ ... 21
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR AWD CONTROL UNIT ... 22
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR ICC UNIT .................... ... 23
DESCRIPTION OF “CAN DIAG SUPPORT MNTR” SCREEN FOR INTELLIGENT KEY UNIT
... 24
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR BCM ............................ ... 25
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR LDW CAMERA UNIT ... ... 26
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR UNIFIED METER AND A/
C AMP. .............................................................. ... 27
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR ABS ACTUATOR AND
ELECTRIC UNIT (CONTROL UNIT) ................ ... 28
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR DRIVER SEAT CON-
TROL UNIT ...................................................... ... 28
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR IPDM E/R .................... ... 29
CAN COMMUNICATION ........................................ ... 30
System Description .............................................. ... 30
CAN Communication Unit .................................... ... 30
TYPE 1/TYPE 2/TYPE 9 .................................. ... 30
TYPE 3/TYPE 4 ................................................ ... 34
TYPE 5/TYPE 6/TYPE 10 ................................ ... 38
TYPE 7/TYPE 8 ................................................ ... 42
CAN SYSTEM (TYPE 1) ........................................ ... 47
Component Parts and Harness Connector Location ... 47
Schematic ............................................................ ... 48
Wiring Diagram - CAN - ....................................... ... 49
Check Sheet ........................................................ ... 52
CHECK SHEET RESULTS (EXAMPLE) .......... ... 54
Inspection Between TCM and Data Link Connector
Circuit .................................................................. ... 70
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... ... 71
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. ... 71
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit ... 72
ECM Circuit Inspection ........................................ ... 73
TCM Circuit Inspection ........................................ ... 73

LAN-2Revision: 2005 July 2005 FX
Display Unit Circuit Inspection .............................
... 74
Data Link Connector Circuit Inspection ............... ... 74
BCM Circuit Inspection ........................................ ... 75
Steering Angle Sensor Circuit Inspection ............ ... 75
Unified Meter and A/C Amp. Circuit Inspection ... ... 76
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................ ... 76
Driver Seat Control Unit Circuit Inspection .......... ... 77
IPDM E/R Circuit Inspection ................................ ... 78
CAN Communication Circuit Inspection ............... ... 78
IPDM E/R Ignition Relay Circuit Inspection ......... ... 84
CAN SYSTEM (TYPE 2) ........................................ ... 85
Component Parts and Harness Connector Location ... 85
Schematic ............................................................ ... 86
Wiring Diagram - CAN - ....................................... ... 87
Check Sheet ........................................................ ... 90
CHECK SHEET RESULTS (EXAMPLE) .......... ... 93
Inspection Between TCM and Data Link Connector
Circuit .................................................................. .110
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... ..111
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. ..111
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .112
ECM Circuit Inspection ........................................ .113
TCM Circuit Inspection ........................................ .113
Display Unit Circuit Inspection ............................. .114
Data Link Connector Circuit Inspection ............... .114
BCM Circuit Inspection ........................................ .115
Steering Angle Sensor Circuit Inspection ............ .115
LDW Camera Unit Circuit Inspection ................... .116
Unified Meter and A/C Amp. Circuit Inspection ... .117
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................ .117
Driver Seat Control Unit Circuit Inspection .......... .118
IPDM E/R Circuit Inspection ................................ .118
CAN Communication Circuit Inspection ............... .119
IPDM E/R Ignition Relay Circuit Inspection ......... .125
CAN SYSTEM (TYPE 3) ........................................ .126
Component Parts and Harness Connector Location .126
Schematic ............................................................ .127
Wiring Diagram - CAN - ....................................... .128
Check Sheet ........................................................ .131
CHECK SHEET RESULTS (EXAMPLE) .......... .135
Inspection Between TCM and Data Link Connector
Circuit .................................................................. .154
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... .155
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. .155
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .156
ECM Circuit Inspection ........................................ .157
TCM Circuit Inspection ........................................ .157
Display Control Unit Circuit Inspection ................ .158
ICC Unit Circuit Inspection .................................. .158 Intelligent Key Unit Circuit Inspection ..................
.159
Data Link Connector Circuit Inspection ................ .159
BCM Circuit Inspection ........................................ .160
Steering Angle Sensor Circuit Inspection ............. .160
Unified Meter and A/C Amp. Circuit Inspection .... .161
ICC Sensor Circuit Inspection .............................. .161
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................. .162
Driver Seat Control Unit Circuit Inspection .......... .162
IPDM E/R Circuit Inspection ................................ .163
CAN Communication Circuit Inspection ............... .164
IPDM E/R Ignition Relay Circuit Inspection .......... .170
CAN SYSTEM (TYPE 4) ......................................... .171
Component Parts and Harness Connector Location .171
Schematic ............................................................ .172
Wiring Diagram - CAN - ....................................... .173
Check Sheet ........................................................ .176
CHECK SHEET RESULTS (EXAMPLE) ........... .180
Inspection Between TCM and Data Link Connector
Circuit ................................................................... .200
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... .201
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit ................................................................... .201
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .202
ECM Circuit Inspection ........................................ .203
TCM Circuit Inspection ......................................... .203
Display Control Unit Circuit Inspection ................. .204
ICC Unit Circuit Inspection ................................... .204
Intelligent Key Unit Circuit Inspection .................. .205
Data Link Connector Circuit Inspection ................ .205
BCM Circuit Inspection ........................................ .206
Steering Angle Sensor Circuit Inspection ............. .206
LDW Camera Unit Circuit Inspection ................... .207
Unified Meter and A/C Amp. Circuit Inspection .... .208
ICC Sensor Circuit Inspection .............................. .208
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................. .209
Driver Seat Control Unit Circuit Inspection .......... .209
IPDM E/R Circuit Inspection ................................ .210
CAN Communication Circuit Inspection ............... .211
IPDM E/R Ignition Relay Circuit Inspection .......... .218
CAN SYSTEM (TYPE 5) ......................................... .219
Component Parts and Harness Connector Location .219
Schematic ............................................................ .220
Wiring Diagram - CAN - ....................................... .221
Check Sheet ........................................................ .224
CHECK SHEET RESULTS (EXAMPLE) ........... .227
Inspection Between TCM and Data Link Connector
Circuit ................................................................... .244
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... .245
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit ................................................................... .245
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .246