brake sensor INFINITI FX35 2007 Owners Manual

EC-14Revision: 2006 July 2007 FX35/FX45
Component Inspection .........................................
1286
Removal and Installation ..................................... 1286
DTC P2A00, P2A03 A/F SENSOR 1 ..................... 1287
Component Description ....................................... 1287
CONSULT-II Reference Value in Data Monitor Mode 1287
On Board Diagnosis Logic ................................... 1287
DTC Confirmation Procedure .............................. 1288
Wiring Diagram .................................................... 1289
Diagnostic Procedure .......................................... 1292
Removal and Installation ..................................... 1298
ASCD BRAKE SWITCH ......................................... 1299
Component Description ....................................... 1299
CONSULT-II Reference Value in Data Monitor Mode 1299
Wiring Diagram .................................................... 1300
Diagnostic Procedure .......................................... 1301
Component Inspection ......................................... 1305
ASCD INDICATOR ................................................. 1306
Component Description ....................................... 1306
CONSULT-II Reference Value in Data Monitor Mode 1306
Wiring Diagram .................................................... 1307
Diagnostic Procedure .......................................... 1308
ELECTRICAL LOAD SIGNAL ............................... 1309
Description ........................................................... 1309
CONSULT-II Reference Value in Data Monitor Mode 1309
Diagnostic Procedure .......................................... 1309
FUEL INJECTOR ................................................... 1311
Component Description ....................................... 1311
CONSULT-II Reference Value in Data Monitor Mode
1311
Wiring Diagram .................................................... 1312
Diagnostic Procedure .......................................... 1313
Component Inspection ......................................... 1317
Removal and Installation ..................................... 1317
FUEL PUMP ........................................................... 1318
Description ........................................................... 1318
CONSULT-II Reference Value in Data Monitor Mode 1318
Wiring Diagram .................................................... 1319
Diagnostic Procedure .......................................... 1320
Component Inspection ......................................... 1323
Removal and Installation ..................................... 1323
ICC BRAKE SWITCH ............................................. 1324
Component Description ....................................... 1324
CONSULT-II Reference Value in Data Monitor Mode 1324
Wiring Diagram .................................................... 1325
Diagnostic Procedure ........................................... 1326
Component Inspection ......................................... 1331
IGNITION SIGNAL ................................................. 1332
Component Description ....................................... 1332
Wiring Diagram .................................................... 1333
Diagnostic Procedure ........................................... 1338
Component Inspection ......................................... 1343
Removal and Installation ...................................... 1344
REFRIGERANT PRESSURE SENSOR ................. 1345
Component Description ....................................... 1345
Wiring Diagram .................................................... 1346
Diagnostic Procedure ........................................... 1347
Removal and Installation ...................................... 1349
SNOW MODE SWITCH .......................................... 1350
Description ........................................................... 1350
CONSULT-II Reference Value in the Data Monitor
Mode .................................................................... 1350
Wiring Diagram .................................................... 1351
Diagnostic Procedure ........................................... 1352
Component Inspection ......................................... 1354
VARIABLE INDUCTION AIR CONTROL SYSTEM
(VIAS) ..................................................................... 1355
Description ........................................................... 1355
CONSULT-II Reference Value in Data Monitor Mode 1356
Wiring Diagram .................................................... 1357
Diagnostic Procedure ........................................... 1359
Component Inspection ......................................... 1362
Removal and Installation ...................................... 1363
MIL AND DATA LINK CONNECTOR ..................... 1364
Wiring Diagram .................................................... 1364
SERVICE DATA AND SPECIFICATIONS (SDS) ... 1366
Fuel Pressure ....................................................... 1366
Idle Speed and Ignition Timing ............................. 1366
Calculated Load Value ......................................... 1366
Mass Air Flow Sensor .......................................... 1366
Intake Air Temperature Sensor ............................ 1366
Engine Coolant Temperature Sensor ................... 1366
Fuel Tank Temperature Sensor ............................ 1366
Crankshaft Position Sensor (POS) ...................... 1366
Camshaft Position Sensor (PHASE) .................... 1366
A/F Sensor 1 Heater ............................................ 1366
Heated Oxygen sensor 2 Heater ......................... 1367
Throttle Control Motor .......................................... 1367
Fuel Injector ......................................................... 1367
Fuel Pump ............................................................ 1367

INDEX FOR DTC EC-17
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45P0456 0456 EVAP VERY SML LEAK EC-449
P0460 0460 FUEL LEV SEN SLOSHEC-459
P0461 0461 FUEL LEVEL SENSOREC-461
P0462 0462 FUEL LEVL SEN/CIRCEC-463
P0463 0463 FUEL LEVL SEN/CIRCEC-463
P0500 0500
VEH SPEED SEN/CIRC*5EC-465
P0506 0506 ISC SYSTEM EC-467
P0507 0507 ISC SYSTEMEC-469
P0550 0550 PW ST P SEN/CIRCEC-471
P0603 0603 ECM BACK UP/CIRCUITEC-476
P0605 0605 ECMEC-480
P0643 0643 SENSOR POWER/CIRCEC-483
P0700 0700 TCM AT- 111
P0705 0705 PNP SW/CIRCAT- 11 2
P0710 0710 ATF TEMP SEN/CIRCAT- 1 3 4
P0717 0717 TURBINE SENSOR AT- 11 6
P0720 0720
VEH SPD SEN/CIR AT*5AT- 11 8
P0740 0740 TCC SOLENOID/CIRC AT- 1 2 5
P0744 0744 A/T TCC S/V FNCTNAT- 1 2 7
P0745 0745 L/PRESS SOL/CIRCAT- 1 2 9
P0850 0850 P-N POS SW/CIRCUITEC-488
P1148 1148 CLOSED LOOP-B1EC-493
P1168 1168 CLOSED LOOP-B2EC-493
P1211 1211 TCS C/U FUNCTNEC-494
P1212 1212 TCS/CIRC EC-495
P1217 1217 ENG OVER TEMPEC-496
P1225 1225 CTP LEARNINGEC-509
P1226 1226 CTP LEARNING EC-511
P1421 1421 COLD START CONTROLEC-513
P1564 1564 ASCD SW EC-515 (Models with ICC),
EC-522
(Models with ASCD)
P1568 1568 ICC COMMAND VALUE*
6EC-529
P1572 1572 ASCD BRAKE SW EC-530 (Models with ICC),
EC-539
(Models with ASCD)
P1574 1574 ASCD VHL SPD SEN EC-547
(Models with ICC),
EC-549
(Models with ASCD)
P1610 - P1615 1610 - 1615 NATS MALFUNCTION EC-551
P1715 1715 IN PULY SPEEDEC-551
P1730 1730 A/T INTERLOCK AT- 1 4 1
P1752 1752 I/C SOLENOID/CIRCAT- 1 4 6
P1754 1754 I/C SOLENOID FNCTNAT- 1 4 8
P1757 1757 FR/B SOLENOID/CIRCAT- 1 5 0
P1759 1759 FR/B SOLENOID FNCTAT- 1 5 2
DTC*1
Items
(CONSULT-II screen terms) Reference page
CONSULT-II
GST*
2ECM*3

EC-18
[VQ35DE]
INDEX FOR DTC
Revision: 2006 July 2007 FX35/FX45
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-II.
*5: When the fail-safe operations for both self-diagnoses occur, the MIL illuminates.
*6: For models with ICC system. P1762 1762 D/C SOLENOID/CIRC
AT-154
P1764 1764 D/C SOLENOID FNCTNAT-156
P1767 1767 HLR/C SOL/CIRCAT-158
P1769 1769 HLR/C SOL FNCTNAT-160
P1772 1772 LC/B SOLENOID/CIRCAT-162
P1774 1774 LC/B SOLENOID FNCTAT-164
P1805 1805 BRAKE SW/CIRCUITEC-552
P2100 2100 ETC MOT PWREC-557
P2101 2101 ETC FUNCTION/CIRCEC-563
P2103 2103 ETC MOT PWREC-557
P 2 11 8 2 11 8 E T C M O TEC-569
P 2 11 9 2 11 9 E T C A C T REC-574
P2122 2122 APP SEN 1/CIRC EC-576
P2123 2123 APP SEN 1/CIRCEC-576
P2127 2127 APP SEN 2/CIRCEC-583
P2128 2128 APP SEN 2/CIRCEC-583
P2135 2135 TP SENSOREC-590
P2138 2138 APP SENSOREC-597
P2A00 2A00 A/F SENSOR1 (B1) EC-605
P2A03 2A03 A/F SENSOR1 (B2)EC-605
DTC*1
Items
(CONSULT-II screen terms) Reference page
CONSULT-II
GST*
2ECM*3

INDEX FOR DTC EC-19
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
Alphabetical IndexNBS003KV
NOTE:

If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-155, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .

If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010.
Refer to EC-158, "
DTC U1010 CAN COMMUNICATION" .
Items
(CONSULT-II screen terms) DTC*
1
Reference page
CONSULT-II
GST*
2ECM*3
A/F SEN1 HTR (B1) P0031 0031 EC-164
A/F SEN1 HTR (B1) P0032 0032EC-164
A/F SEN1 HTR (B2) P0051 0051EC-164
A/F SEN1 HTR (B2) P0052 0052EC-164
A/F SENSOR1 (B1) P0130 0130EC-229
A/F SENSOR1 (B1) P0131 0131EC-239
A/F SENSOR1 (B1) P0132 0132EC-248
A/F SENSOR1 (B1) P0133 0133EC-257
A/F SENSOR1 (B1) P2A00 2A00EC-605
A/F SENSOR1 (B2) P0150 0150EC-229
A/F SENSOR1 (B2) P0151 0151EC-239
A/F SENSOR1 (B2) P0152 0152EC-248
A/F SENSOR1 (B2) P0153 0153EC-257
A/F SENSOR1 (B2) P2A03 2A03EC-605
A/T INTERLOCK P1730 1730 AT- 1 4 1
A/T TCC S/V FNCTN P0744 0744AT- 1 2 7
APP SEN 1/CIRC P2122 2122EC-576
APP SEN 1/CIRC P2123 2123EC-576
APP SEN 2/CIRC P2127 2127EC-583
APP SEN 2/CIRC P2128 2128EC-583
APP SENSOR P2138 2138EC-597
ASCD BRAKE SW P1572 1572 EC-530 (Models with ICC),
EC-539
(Models with ASCD)
ASCD SW P1564 1564 EC-515
(Models with ICC),
EC-522
(Models with ASCD)
ASCD VHL SPD SEN P1574 1574 EC-547
(Models with ICC),
EC-549
(Models with ASCD)
ATF TEMP SEN/CIRC P0710 0710 AT- 1 3 4
BRAKE SW/CIRCUIT P1805 1805EC-552
CAN COMM CIRCUIT U1000
1000*4EC-155
CAN COMM CIRCUIT U10011001*4EC-155
CKP SEN/CIRCUIT P0335 0335 EC-360
CLOSED LOOP-B1 P1148 1148EC-493
CLOSED LOOP-B2 P1168 1168EC-493
CMP SEN/CIRC-B1 P0340 0340EC-367
CMP SEN/CIRC-B2 P0345 0345EC-367
COLD START CONTROL P1421 1421EC-513
CONTROL UNIT(CAN) U1010 1010EC-158

AUTOMATIC SPEED CONTROL DEVICE (ASCD) EC-35
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
AUTOMATIC SPEED CONTROL DEVICE (ASCD)PFP:18930
System DescriptionNBS003L7
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM through CAN communication line.
BASIC ASCD SYSTEM
Refer to Owner's Manual for ASCD operating instructions.
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/
h (25 MPH) and 144 km/h (89 MPH).
ECM controls throttle angle of electric throttle control actuator to regulate engine speed.
Operation status of ASCD is indicated by CRUISE indicator and SET indicator in combination meter. If any
malfunction occurs in ASCD system, it automatically deactivates control.
NOTE:
Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
SET OPERATION
Press MAIN switch. (The CRUISE indicator in combination meter illuminates.)
When vehicle speed reaches a desired speed between approximately 40 km/h (25 MPH) and 144 km/h (89
MPH), press SET/COAST switch. (Then SET indicator in combination meter illuminates.)
ACCELERATOR OPERATION
If the RESUME/ACCELERATE switch is pressed during cruise control driving, increase the vehicle speed until
the switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will keep the new set speed.
CANCEL OPERATION
When any of following conditions exist, cruise operation will be canceled.

CANCEL switch is pressed

More than 2 switches at ASCD steering switch are pressed at the same time (Set speed will be cleared)

Brake pedal is depressed

Selector lever is changed to N, P, R position

Vehicle speed decreased to 13 km/h (8 MPH) lower than the set speed

VDC/TCS system is operated
When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform
the driver by blinking indicator lamp.

Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE lamp may
blink slowly.
When the engine coolant temperature decreases to the normal operating temperature, CRUISE lamp will
stop blinking and the cruise operation will be able to work by depressing SET/COAST switch or RESUME/
ACCELERATE switch.

Malfunction for some self-diagnoses regarding ASCD control: SET lamp will blink quickly.
If MAIN switch is turned to OFF during ASCD is activated, all of ASCD operations will be canceled and vehicle
speed memory will be erased.
COAST OPERATION
When the SET/COAST switch is pressed during cruise control driving, decrease vehicle set speed until the
switch is released. And then ASCD will keep the new set speed.
Sensor Input signal to ECM ECM function Actuator
ASCD brake switch Brake pedal operation
ASCD vehicle speed control Electric throttle control
actuator
Stop lamp switch Brake pedal operation
ASCD steering switch ASCD steering switch operation
Park/neutral position (PNP) switch Gear position
Wheel sensor. Vehicle speed*
TCM Powertrain revolution*

ON BOARD DIAGNOSTIC (OBD) SYSTEM EC-57
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: SRT code will not be set if the self-diagnostic result is NG.
*5: The trouble shooting for this DTC needs CONSULT-II.
*6: When the fail-safe operations for both self-diagnoses occur, the MIL illuminates.
*7: For models with ICC system.
*8: When the ECM is in the mode of displaying SRT status, MIL may flash. For the details, refer to EC-62, "
How to Display SRT Status" .
ASCD BRAKE SW P1572 1572 — — 1 —
EC-530

(Models
with ICC) EC-539

(Models
with ASCD)
ASCD VHL SPD SEN P1574 1574 — — 1 — EC-547

(Models
with ICC) EC-549

(Models
with ASCD)
NATS MALFUNCTION P1610 -
P1615 1610 - 1615 — — 2 —
EC-52
IN PULLY SPEED P1715 1715 — — 2 — EC-551
A/T INTERLOCK P1730 1730 — — 1×AT- 1 4 1
I/C SOLENOID/CIRC P1752 1752 — — 1 ×AT- 1 4 6
I/C SOLENOID FNCTN P1754 1754 — — 1 ×AT- 1 4 8
FR/B SOLENOID/CIRC P1757 1757 — — 1 ×AT- 1 5 0
FR/B SOLENOID FNCT P1759 1759 — — 1 ×AT- 1 5 2
D/C SOLENOID/CIRC P1762 1762 — — 1 ×AT- 1 5 4
D/C SOLENOID FNCTN P1764 1764 — — 1 ×AT- 1 5 6
HLR/C SOL/CIRC P1767 1767 — — 1 ×AT- 1 5 8
HLR/C SOL FNCTN P1769 1769 — — 1 ×AT- 1 6 0
LC/B SOLENOID/CIRC P1772 1772 — — 1 ×AT- 1 6 2
LC/B SOLENOID FNCT P1774 1774 — — 1 ×AT- 1 6 4
BRAKE SW/CIRCUIT P1805 1805 — — 2 — EC-552
ETC MOT PWR P2100 2100 — — 1×EC-557
ETC FUNCTION/CIRC P2101 2101 — — 1 ×EC-563
ETC MOT PWR P2103 2103 — — 1 ×EC-557
ETC MOT P2118 2118 — — 1 ×EC-569
ETC ACTR P2119 2119 — — 1 ×EC-574
APP SEN 1/CIRC P2122 2122 — — 1 ×EC-576
APP SEN 1/CIRC P2123 2123 — — 1 ×EC-576
APP SEN 2/CIRC P2127 2127 — — 1 ×EC-583
APP SEN 2/CIRC P2128 2128 — — 1 ×EC-583
TP SENSOR P2135 2135 — — 1 ×EC-590
APP SENSOR P2138 2138 — — 1 ×EC-597
A/F SENSOR1 (B1) P2A00 2A00 — ×2 ×EC-605
A/F SENSOR1 (B2) P2A03 2A03 — ×2 ×EC-605
Items
(CONSULT-II screen terms) DTC*
1
SRT code
Test value/
Te s t l i m i t
(GST only) Trip MIL
Reference
page
CONSULT-II
GST*
2ECM*3

BASIC SERVICE PROCEDURE EC-83
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
3. Select “VIN REGISTRATION” in “WORK SUPPORT” mode.
4. Follow the instruction of CONSULT-II display.
Accelerator Pedal Released Position LearningNBS003LT
DESCRIPTION
Accelerator Pedal Released Position Learning is an operation to learn the fully released position of the accel-
erator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time
harness connector of accelerator pedal position sensor or ECM is disconnected.
OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch ON and wait at least 2 seconds.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON and wait at least 2 seconds.
5. Turn ignition switch OFF and wait at least 10 seconds.
Throttle Valve Closed Position LearningNBS003LU
DESCRIPTION
Throttle Valve Closed Position Learning is an operation to learn the fully closed position of the throttle valve by
monitoring the throttle position sensor output signal. It must be performed each time harness connector of
electric throttle control actuator or ECM is disconnected.
OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds. Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.
Idle Air Volume LearningNBS003LV
DESCRIPTION
Idle Air Volume Learning is an operation to learn the idle air volume that keeps each engine within the specific
range. It must be performed under any of the following conditions:

Each time electric throttle control actuator or ECM is replaced.

Idle speed or ignition timing is out of specification.
PREPARATION
Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.

Battery voltage: More than 12.9V (At idle)

Engine coolant temperature: 70 - 100 °C (158 - 212 °F)

Park/neutral position switch: ON

Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
On vehicles equipped with daytime light systems, if the parking brake is applied before the engine
is started the headlamp will not be illuminated.

Steering wheel: Neutral (Straight-ahead position)

Vehicle speed: Stopped

Transmission: Warmed-up
PBIB2242E

EC-94
[VQ35DE]
TROUBLE DIAGNOSIS
Revision: 2006 July 2007 FX35/FX45
*: Models with ICC. 2

P0031 P0032 P0051 P0052 Air fuel ratio (A/F) sensor 1 heater

P0037 P0038 P0057 P0058 Heated oxygen sensor 2 heater

P0075 P0081 Intake valve timing control solenoid valve

P0130 P0131 P0132 P0133 P0150 P0151 P0152 P0153 P2A00 P2A03 Air fuel ratio (A/F) sensor 1

P0137 P0138 P0139 P0157 P0158 P0159 Heated oxygen sensor 2

P0441 EVAP control system purge flow monitoring

P0443 P0444 P0445 EVAP canister purge volume control solenoid valve

P0447 P0448 EVAP canister vent control valve

P0451 P0452 P0453 EVAP control system pressure sensor

P0550 Power steering pressure sensor

P0603 ECM power supply

P0710 P0717 P0720 P0740 P0744 P0745 P1730 P1752 P1754 P1757 P1759 P1762 P1764 P1767 P1769 P1772
P1774 A/T related sensors, solenoid valves and switches

P1217 Engine over temperature (OVERHEAT)

P1805 Brake switch

P2100 P2103 P2118 Electric throttle control actuator

P2101 Electric throttle control function
3

P0011 P0021 Intake valve timing control

P0171 P0172 P0174 P0175 Fuel injection system function

P0300 - P0306 Misfire

P0420 P0430 Three way catalyst function

P0442 EVAP control system (SMALL LEAK)

P0455 EVAP control system (GROSS LEAK)

P0456 EVAP control system (VERY SMALL LEAK)

P0506 P0507 Idle speed control system

P1148 P1168 Closed loop control

P1211 TCS control unit

P1212 TCS communication line

P1421 COLD START CONTROL

P1564 ICC steering switch/ASCD steering switch

P1568 ICC command valve*

P1572 ICC brake switch/ASCD brake switch

P1574 ICC vehicle speed sensor/ASCD vehicle speed sensor

P1715 Turbine revolution sensor

P2119 Electric throttle control actuator
Priority Detected items (DTC)

TROUBLE DIAGNOSIS EC-117
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45101 P/L Stop lamp switch [Ignition switch: OFF]
Brake pedal: Fully released
Approximately 0V
[Ignition switch: OFF]

Brake pedal: Slightly depressed BATTERY VOLTAGE
(11 - 14V)
102 LG/B PNP switch [Ignition switch: ON]

Selector lever: P or N
Approximately 0V
[Ignition switch: ON]

Except above position BATTERY VOLTAGE
(11 - 14V)
104 L/OR Throttle control motor relay [Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14V)
[Ignition switch: ON] 0 - 1.0V
106 OR Accelerator pedal position
sensor 1 [Ignition switch: ON]

Engine stopped

Accelerator pedal: Fully released
0.5 - 1.0V
[Ignition switch: ON]

Engine stopped

Accelerator pedal: Fully depressed 3.9 - 4.7V
107 PU/W Fuel tank temperature sen-
sor [Engine is running] Approximately 0 - 4.8V
Output voltage varies with fuel
tank temperature.
108 SB ICC brake switch
(models with ICC system)
ASCD brake switch
(models with ASCD system) [Ignition switch: ON]

Brake pedal: Slightly depressed
Approximately 0V
[Ignition switch: ON]

Brake pedal: Fully released BATTERY VOLTAGE
(11 - 14V)
109 W/L Ignition switch [Ignition switch: OFF]
0V
[Ignition switch: ON] BATTERY VOLTAGE
(11 - 14V)
111 W / B ECM relay
(Self shut-off) [Engine is running]
[Ignition switch: OFF]

For a few seconds after turning ignition
switch OFF 0 - 1.5V
[Ignition switch: OFF]

More than a few seconds after turning igni-
tion switch OFF BATTERY VOLTAGE
(11 - 14V)
113 GY/R Fuel pump relay [Ignition switch: ON]

For 1 second after turning ignition switch ON
[Engine is running] 0 - 1.5V
[Ignition switch: ON]

More than 1 second after turning ignition
switch ON BATTERY VOLTAGE
(11 - 14V)
11 5
11 6 B/R
B/W ECM ground [Engine is running]

Idle speed Body ground
11 7 R / Y EVAP canister vent control
valve [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14V)
11 9
120 R
R/B Power supply for ECM
[Ignition switch: ON] BATTERY VOLTAGE
(11 - 14V)
121 R/W Power supply for ECM
(Back-up) [Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14V)
TER-
MINAL NO. WIRE
COLOR ITEM CONDITION DATA (DC Voltage)

TROUBLE DIAGNOSIS EC-119
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
ENGINE CONTROL COMPONENT PARTS/CONTROL SYSTEMS APPLICATION
Item DIAGNOSTIC TEST MODE
WORK SUP-
PORT SELF-DIAGNOSTIC
RESULTS DATA
MONI-
TOR DATA
MONI- TOR
(SPEC) ACTIVE
TEST DTC & SRT
CONFIRMATION
DTC*1FREEZE
FRAME
DATA*
1
SRT
STATUS DTC
WORK SUP-
PORT
ENGINE CONTROL COMPONENT PARTS
INPUT
Crankshaft position sensor (POS) ××××
Camshaft position sensor (PHASE) ××××
Mass air flow sensor ×××
Engine coolant temperature sensor ×××××
Air fuel ratio (A/F) sensor 1 ×××××
Heated oxygen sensor 2 ×××××
Vehicle speed sensor ××××
Accelerator pedal position sensor ×××
Throttle position sensor ××××
Fuel tank temperature sensor ××××
EVAP control system pressure
sensor ×××
Intake air temperature sensor ××××
Knock sensor ×
Refrigerant pressure sensor ××
Closed throttle position switch
(accelerator pedal position sensor
signal) ××
Air conditioner switch ××
Park/neutral position (PNP) switch ×××
Stop lamp switch ×××
Power steering pressure sensor ×××
Battery voltage ××
Load signal ××
Fuel level sensor ×××
ICC steering switch ×××
ASCD steering switch ×××
ICC brake switch ×××
ASCD brake switch ×××
Snow mode switch ××