INFINITI FX35 2007 Service Manual

REAR VIEW MONITOR DI-125
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2006 July 2007 FX35/FX45
3. CHECK DISPLAY CONTROL UNIT OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector.
3. Turn ignition switch ON.
4. Check voltage between rear view camera control unit harness connector M48 terminal 5 and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
4. CHECK DISPLAY CONTROL UNIT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display control unit connector.
3. Check continuity between rear view camera control unit harness connector M48 terminal 5 and display control unit harness con-
nector M75 terminal 8.
4. Check continuity between rear view camera control unit harness connector M48 terminal 5 and ground.
OK or NG
OK >> Replace display control unit.
NG >> Repair harness or connector.
5. CHECK CONTROL 1 SIGNAL
1. Turn ignition switch OFF.
2. Connect rear view camera control unit connector.
3. Turn ignition switch ON.
4. Shift A/T selector lever to R position.
5. Check voltage between rear view camera control unit harness connector M48 terminal 5 and ground.
OK or NG
OK >> GO TO 6.
NG >> Replace rear view camera control unit. 5 – Ground : Approx. 5 V
SKIA7148E
5 – 8 : Continuity should exist.
5 – Ground : Continuity should not exist.
SKIA7149E
5 – Ground : Approx. 0 V
SKIA7150E

DI-126
REAR VIEW MONITOR
Revision: 2006 July 2007 FX35/FX45
6. CHECK REAR VIEW CAMERA OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera connector.
3. Check continuity between rear view camera control unit harness connector M48 terminal 8 and rear view camera harness con-
nector D108 terminal 1.
4. Check continuity between rear view camera control unit harness connector M48 terminal 9 and rear view camera harness con-
nector D108 terminal 4.
5. Check continuity between rear view camera control unit harness connector M48 terminal 10 and rear view camera harness con-
nector D108 terminal 3.
OK or NG
OK >> GO TO 7.
NG >> Repair harness or connector.
7. CHECK REAR VIEW CAMERA SHORT CIRCUIT
1. Check continuity between rear view camera control unit harness connector M48 terminal 8 and ground.
2. Check continuity between rear view camera control unit harness connector M48 terminal 9 and ground.
3. Check continuity between rear view camera control unit harness connector M48 terminal 10 and ground.
OK or NG
OK >> GO TO 8.
NG >> Repair harness on connector.
8. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit. Refer to DI-123, "
Power Supply and Ground Circuit Inspection" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace power supply and ground circuit. 8 – 1 : Continuity should exist.
9 – 4 : Continuity should exist.
10 – 3 : Continuity should exist.
SKIA5095E
8 – Ground : Continuity should not exist.
9 – Ground : Continuity should not exist.
10 – Ground : Continuity should not exist.
SKIA5098E

REAR VIEW MONITOR DI-127
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2006 July 2007 FX35/FX45
9. CHECK REAR VIEW CAMERA CONTROL UNIT OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Connect rear view camera control unit connector.
3. Turn ignition switch ON.
4. Shift A/T selector lever to R position.
5. Check voltage between rear view camera control unit harness connector M48 terminal 8 and ground.
OK or NG
OK >> GO TO 10.
NG >> Replace rear view camera control unit.
10. CHECK REAR VIEW CAMERA SIGNAL
1. Turn ignition switch OFF.
2. Connect rear view camera connector.
3. Turn ignition switch ON.
4. Shift A/T selector lever to R position.
5. Check voltage signal between rear view camera control unit har- ness connector M48 terminal 10 and ground.
OK or NG
OK >> GO TO 11.
NG >> Replace rear view camera.
11 . CHECK COMPOSITE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector and display connector.
3. Check continuity between rear view camera control unit harness connector M48 terminal 12 and display harness connector M63
terminal 15.
4. Check continuity between rear view camera control unit harness connector M48 terminal 12 and ground.
OK or NG
OK >> GO TO 12.
NG >> Repair harness or connector. 8 – Ground : Approx. 6 V
PKIB3581E
10 – Ground:
PKIB3582E
SKIA4894E
12 – 15 : Continuity should exist.
12 – Ground : Continuity should not exist.
SKIB0482E

DI-128
REAR VIEW MONITOR
Revision: 2006 July 2007 FX35/FX45
12. CHECK COMPOSITE SIGNAL GROUND CIRCUIT
1. Check continuity between rear view camera control unit harness connector M48 terminal 11 and display harness connector M63
terminal 4.
2. Check continuity between rear view camera control unit harness connector M48 terminal 11 and ground.
OK or NG
OK >> GO TO 13.
NG >> Repair harness or connector.
13. CHECK COMPOSITE SIGNAL
1. Connect rear view camera control unit connector and display connector.
2. Turn ignition switch ON.
3. Shift A/T selector lever to R position.
4. Check voltage signal between rear view camera control unit har- ness connector M48 terminal 12 and ground.
OK or NG
OK >> Replace display.
NG >> Replace rear view camera control unit.
The Rear View Image Is DistortedNKS00322
1. CHECK SYNCHRO SIGNAL OPEN OR SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector and display connector.
3. Check continuity between rear view camera control unit harness connector M48 terminal 14 and display harness connector M63
terminal 16.
4. Check continuity between rear view camera control unit harness connector M48 terminal 14 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector. 11 – 4 : Continuity should exist.
11 – Ground : Continuity should not exist.
SKIA5102E
12 – Ground:
PKIB3583E
SKIA4896E
14 – 16 : Continuity should exist.
14 – Ground : Continuity should not exist.
SKIA5101E

REAR VIEW MONITOR DI-129
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2006 July 2007 FX35/FX45
2. CHECK COMPOSITE SIGNAL GROUND CIRCUIT
1. Check continuity between rear view camera control unit harness connector M48 terminal 11 and display harness connector M63
terminal 4.
2. Check continuity between rear view camera control unit harness connector M48 terminal 11 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK REAR VIEW CONTROL UNIT SYNCHRO SIGNAL
1. Connect rear view camera control unit connector and display connector.
2. Turn ignition switch ON.
3. Shift A/T selector lever to R position.
4. Check voltage signal between rear view camera control unit har- ness connector M48 terminal 14 and ground.
OK or NG
OK >> Replace rear view camera control unit.
NG >> Replace display.
Removal and Installation of Rear View Camera Control UnitNKS00323
REMOVAL
1. Remove instrument clock finisher and A/T console finisher. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws (2), and remove rear view camera control unit.
INSTALLATION
Installation is the reverse order of removal. 11 – 4 : Continuity should exist.
11 – Ground : Continuity should not exist.
SKIA5102E
14 – Ground:
PKIB3584E
SKIA5896E
SKIA5797E

DI-130
REAR VIEW MONITOR
Revision: 2006 July 2007 FX35/FX45
Removal and Installation of Rear View CameraNKS00324
REMOVAL
1. Remove back door trim. Refer to EI-47, "BACK DOOR TRIM" .
2. Remove back door outside finisher upper. Refer to EI-35, "
BACK DOOR FINISHER" .
3. Remove licence lamp bolts (A).
4. Disconnect rear wiper connector.
5. Disconnect rear view camera connector (1) and back door opener switch connector (2).
6. Cut off back door module along the line (A).
7. Remove back door opener switch and rear view camera assem- bly (3).

Rear wiper (4)
8. Remove screws (A), and remove rear view camera (1) from back door opener switch (2).
INSTALLATION
Installation is the reverse order of removal.
SKIB8490E
SKIB8491E
SKIB8492E

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D E
F
G H
I
J
K L
M
SECTION
A
EC
Revision: 2006 July 2007 FX35/FX45
ENGINE CONTROL SYSTEM
VQ35DE
INDEX FOR DTC ...................................................... 15
DTC No. Index .................................................... ... 15
Alphabetical Index ............................................... ... 19
PRECAUTIONS ..................................................... ... 23
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ... 23
Precautions for Procedures without Cowl Top Cover ... 23
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... ... 23
Precaution ........................................................... ... 24
PREPARATION ...................................................... ... 27
Special Service Tools .......................................... ... 27
Commercial Service Tools ................................... ... 28
ENGINE CONTROL SYSTEM ............................... ... 29
System Diagram .................................................. ... 29
Multiport Fuel Injection (MFI) System ................. ... 30
Electronic Ignition (EI) System ............................ ... 32
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. ... 33
AIR CONDITIONING CUT CONTROL .................. ... 34
Input/Output Signal Chart .................................... ... 34
System Description ............................................. ... 34
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 35
System Description ............................................. ... 35
Component Description ....................................... ... 36
CAN COMMUNICATION ....................................... ... 37
System Description ............................................. ... 37
EVAPORATIVE EMISSION SYSTEM .................... ... 38
Description .......................................................... ... 38
Component Inspection ........................................ ... 41
Removal and Installation ..................................... ... 42
How to Detect Fuel Vapor Leakage .................... ... 42
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... ... 45
System Description ............................................. ... 45
Diagnostic Procedure .......................................... ... 46
Component Inspection ........................................ ... 48 POSITIVE CRANKCASE VENTILATION ..............
... 50
Description ........................................................... ... 50
Component Inspection ......................................... ... 50
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... ... 52
Description ........................................................... ... 52
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 53
Introduction .......................................................... ... 53
Two Trip Detection Logic ..................................... ... 53
Emission-Related Diagnostic Information ............ ... 54
Malfunction Indicator Lamp (MIL) ........................ ... 67
OBD System Operation Chart ............................. ... 71
BASIC SERVICE PROCEDURE ............................ ... 76
Basic Inspection .................................................. ... 76
Idle Speed and Ignition Timing Check ................. ... 81
Procedure After Replacing ECM ......................... ... 82
VIN Registration .................................................. ... 82
Accelerator Pedal Released Position Learning ... ... 83
Throttle Valve Closed Position Learning .............. ... 83
Idle Air Volume Learning ..................................... ... 83
Fuel Pressure Check ........................................... ... 85
TROUBLE DIAGNOSIS ......................................... ... 87
Trouble Diagnosis Introduction ............................ ... 87
DTC Inspection Priority Chart .............................. ... 93
Fail-Safe Chart .................................................... ... 95
Symptom Matrix Chart ......................................... ... 96
Engine Control Component Parts Location ......... .100
Vacuum Hose Drawing ........................................ .106
Circuit Diagram .................................................... .107
ECM Harness Connector Terminal Layout .......... .109
ECM Terminals and Reference Value .................. .109
CONSULT-II Function (ENGINE) ......................... .118
Generic Scan Tool (GST) Function ...................... .129
CONSULT-II Reference Value in Data Monitor .... .132
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .134
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .137
Description ........................................................... .137
Testing Condition ................................................. .137

EC-2Revision: 2006 July 2007 FX35/FX45
Inspection Procedure ...........................................
.137
Diagnostic Procedure .......................................... .138
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ...................................................................... .147
Description ........................................................... .147
Diagnostic Procedure .......................................... .147
POWER SUPPLY AND GROUND CIRCUIT .......... .148
Wiring Diagram .................................................... .148
Diagnostic Procedure .......................................... .149
Ground Inspection ............................................... .153
DTC U1000, U1001 CAN COMMUNICATION LINE .155
Description ........................................................... .155
On Board Diagnosis Logic ................................... .155
DTC Confirmation Procedure .............................. .155
Wiring Diagram .................................................... .156
Diagnostic Procedure .......................................... .157
DTC U1010 CAN COMMUNICATION .................... .158
Description ........................................................... .158
On Board Diagnosis Logic ................................... .158
DTC Confirmation Procedure .............................. .158
Diagnostic Procedure .......................................... .159
DTC P0011, P0021 IVT CONTROL ....................... .160
Description ........................................................... .160
CONSULT-II Reference Value in Data Monitor Mode .160
On Board Diagnosis Logic ................................... .161
DTC Confirmation Procedure .............................. .161
Diagnostic Procedure .......................................... .162
Component Inspection ......................................... .163
Removal and Installation ..................................... .163
DTC P0031, P0032, P0051, P0052 A/F SENSOR 1
HEATER ................................................................. .164
Description ........................................................... .164
CONSULT-II Reference Value in Data Monitor Mode .164
On Board Diagnosis Logic ................................... .164
DTC Confirmation Procedure .............................. .164
Wiring Diagram .................................................... .166
Diagnostic Procedure .......................................... .169
Component Inspection ......................................... .171
Removal and Installation ..................................... .171
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .172
Description ........................................................... .172
CONSULT-II Reference Value in Data Monitor Mode .172
On Board Diagnosis Logic ................................... .172
DTC Confirmation Procedure .............................. .173
Wiring Diagram .................................................... .174
Diagnostic Procedure .......................................... .177
Component Inspection ......................................... .179
Removal and Installation ..................................... .179
DTC P0075, P0081 IVT CONTROL SOLENOID
VALVE .................................................................... .180
Component Description ....................................... .180
CONSULT-II Reference Value in Data Monitor Mode .180
On Board Diagnosis Logic ................................... .180
DTC Confirmation Procedure .............................. .180
Wiring Diagram .................................................... .181 Diagnostic Procedure ...........................................
.185
Component Inspection ......................................... .186
Removal and Installation ...................................... .186
DTC P0101 MAF SENSOR .................................... .187
Component Description ....................................... .187
CONSULT-II Reference Value in Data Monitor Mode .187
On Board Diagnosis Logic ................................... .187
DTC Confirmation Procedure ............................... .188
Overall Function Check ........................................ .189
Wiring Diagram .................................................... .190
Diagnostic Procedure ........................................... .191
Component Inspection ......................................... .194
Removal and Installation ...................................... .195
DTC P0102, P0103 MAF SENSOR ........................ .196
Component Description ....................................... .196
CONSULT-II Reference Value in Data Monitor Mode .196
On Board Diagnosis Logic ................................... .196
DTC Confirmation Procedure ............................... .197
Wiring Diagram .................................................... .198
Diagnostic Procedure ........................................... .199
Component Inspection ......................................... .202
Removal and Installation ...................................... .203
DTC P0112, P0113 IAT SENSOR ........................... .204
Component Description ....................................... .204
On Board Diagnosis Logic ................................... .204
DTC Confirmation Procedure ............................... .204
Wiring Diagram .................................................... .206
Diagnostic Procedure ........................................... .207
Component Inspection ......................................... .208
Removal and Installation ...................................... .208
DTC P0117, P0118 ECT SENSOR ......................... .209
Component Description ....................................... .209
On Board Diagnosis Logic ................................... .209
DTC Confirmation Procedure ............................... .210
Wiring Diagram .................................................... .211
Diagnostic Procedure ........................................... .212
Component Inspection ......................................... .213
Removal and Installation ...................................... .213
DTC P0122, P0123 TP SENSOR ........................... .214
Component Description ....................................... .214
CONSULT-II Reference Value in Data Monitor Mode .214
On Board Diagnosis Logic ................................... .214
DTC Confirmation Procedure ............................... .215
Wiring Diagram .................................................... .216
Diagnostic Procedure ........................................... .217
Component Inspection ......................................... .220
Removal and Installation ...................................... .220
DTC P0125 ECT SENSOR ..................................... .221
Component Description ....................................... .221
On Board Diagnosis Logic ................................... .221
DTC Confirmation Procedure ............................... .222
Diagnostic Procedure ........................................... .222
Component Inspection ......................................... .223
Removal and Installation ...................................... .223
DTC P0127 IAT SENSOR ....................................... .224
Component Description ....................................... .224

EC-3
C
D E
F
G H
I
J
K L
M
EC A
Revision: 2006 July 2007 FX35/FX45
On Board Diagnosis Logic ..................................
. 224
DTC Confirmation Procedure .............................. . 224
Diagnostic Procedure .......................................... . 225
Component Inspection ........................................ . 226
Removal and Installation ..................................... . 226
DTC P0128 THERMOSTAT FUNCTION ............... . 227
On Board Diagnosis Logic .................................. . 227
DTC Confirmation Procedure .............................. . 227
Diagnostic Procedure .......................................... . 227
Component Inspection ........................................ . 228
Removal and Installation ..................................... . 228
DTC P0130, P0150 A/F SENSOR 1 ...................... . 229
Component Description ....................................... . 229
CONSULT-II Reference Value in Data Monitor Mode . 229
On Board Diagnosis Logic .................................. . 229
DTC Confirmation Procedure .............................. . 229
Overall Function Check ....................................... . 231
Wiring Diagram ................................................... . 232
Diagnostic Procedure .......................................... . 235
Removal and Installation ..................................... . 238
DTC P0131, P0151 A/F SENSOR 1 ...................... . 239
Component Description ....................................... . 239
CONSULT-II Reference Value in Data Monitor Mode . 239
On Board Diagnosis Logic .................................. . 239
DTC Confirmation Procedure .............................. . 240
Wiring Diagram ................................................... . 241
Diagnostic Procedure .......................................... . 244
Removal and Installation ..................................... . 247
DTC P0132, P0152 A/F SENSOR 1 ...................... . 248
Component Description ....................................... . 248
CONSULT-II Reference Value in Data Monitor Mode . 248
On Board Diagnosis Logic .................................. . 248
DTC Confirmation Procedure .............................. . 249
Wiring Diagram ................................................... . 250
Diagnostic Procedure .......................................... . 253
Removal and Installation ..................................... . 256
DTC P0133, P0153 A/F SENSOR 1 ...................... . 257
Component Description ....................................... . 257
CONSULT-II Reference Value in Data Monitor Mode . 257
On Board Diagnosis Logic .................................. . 257
DTC Confirmation Procedure .............................. . 258
Wiring Diagram ................................................... . 260
Diagnostic Procedure .......................................... . 263
Removal and Installation ..................................... . 268
DTC P0137, P0157 HO2S2 ................................... . 269
Component Description ....................................... . 269
CONSULT-II Reference Value in Data Monitor Mode . 269
On Board Diagnosis Logic .................................. . 269
DTC Confirmation Procedure .............................. . 270
Overall Function Check ....................................... . 270
Wiring Diagram ................................................... . 272
Diagnostic Procedure .......................................... . 275
Component Inspection ........................................ . 277
Removal and Installation ..................................... . 279 DTC P0138, P0158 HO2S2 ....................................
.280
Component Description ....................................... .280
CONSULT-II Reference Value in Data Monitor Mode .280
On Board Diagnosis Logic ................................... .280
DTC Confirmation Procedure .............................. .281
Overall Function Check ....................................... .282
Wiring Diagram .................................................... .283
Diagnostic Procedure .......................................... .286
Component Inspection ......................................... .290
Removal and Installation ..................................... .292
DTC P0139, P0159 HO2S2 .................................... .293
Component Description ....................................... .293
CONSULT-II Reference Value in Data Monitor Mode .293
On Board Diagnosis Logic ................................... .293
DTC Confirmation Procedure .............................. .294
Overall Function Check ....................................... .294
Wiring Diagram .................................................... .296
Diagnostic Procedure .......................................... .299
Component Inspection ......................................... .301
Removal and Installation ..................................... .303
DTC P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION ............................................................. .304
On Board Diagnosis Logic ................................... .304
DTC Confirmation Procedure .............................. .304
Wiring Diagram .................................................... .306
Diagnostic Procedure .......................................... .310
DTC P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION ............................................................. .316
On Board Diagnosis Logic ................................... .316
DTC Confirmation Procedure .............................. .316
Wiring Diagram .................................................... .318
Diagnostic Procedure .......................................... .322
DTC P0181 FTT SENSOR ..................................... .327
Component Description ....................................... .327
On Board Diagnosis Logic ................................... .327
DTC Confirmation Procedure .............................. .327
Wiring Diagram .................................................... .329
Diagnostic Procedure .......................................... .330
Component Inspection ......................................... .332
Removal and Installation ..................................... .332
DTC P0182, P0183 FTT SENSOR ......................... .333
Component Description ....................................... .333
On Board Diagnosis Logic ................................... .333
DTC Confirmation Procedure .............................. .333
Wiring Diagram .................................................... .334
Diagnostic Procedure .......................................... .335
Component Inspection ......................................... .337
Removal and Installation ..................................... .337
DTC P0222, P0223 TP SENSOR ........................... .338
Component Description ....................................... .338
CONSULT-II Reference Value in Data Monitor Mode .338
On Board Diagnosis Logic ................................... .338
DTC Confirmation Procedure .............................. .339
Wiring Diagram .................................................... .340
Diagnostic Procedure .......................................... .341

EC-4Revision: 2006 July 2007 FX35/FX45
Component Inspection .........................................
.344
Removal and Installation ..................................... .344
DTC P0300 - P0306 MULTIPLE CYLINDER MIS-
FIRE, NO. 1 - 6 CYLINDER MISFIRE .................... .345
On Board Diagnosis Logic ................................... .345
DTC Confirmation Procedure .............................. .346
Diagnostic Procedure .......................................... .346
DTC P0327, P0328 KS ........................................... .355
Component Description ....................................... .355
On Board Diagnosis Logic ................................... .355
DTC Confirmation Procedure .............................. .355
Wiring Diagram .................................................... .356
Diagnostic Procedure .......................................... .357
Component Inspection ......................................... .358
Removal and Installation ..................................... .359
DTC P0335 CKP SENSOR (POS) ......................... .360
Component Description ....................................... .360
CONSULT-II Reference Value in Data Monitor Mode .360
On Board Diagnosis Logic ................................... .360
DTC Confirmation Procedure .............................. .361
Wiring Diagram .................................................... .362
Diagnostic Procedure .......................................... .363
Component Inspection ......................................... .366
Removal and Installation ..................................... .366
DTC P0340, P0345 CMP SENSOR (PHASE) ........ .367
Component Description ....................................... .367
CONSULT-II Reference Value in Data Monitor Mode .367
On Board Diagnosis Logic ................................... .367
DTC Confirmation Procedure .............................. .368
Wiring Diagram .................................................... .369
Diagnostic Procedure .......................................... .372
Component Inspection ......................................... .375
Removal and Installation ..................................... .375
DTC P0420, P0430 THREE WAY CATALYST FUNC-
TION ....................................................................... .376
On Board Diagnosis Logic ................................... .376
DTC Confirmation Procedure .............................. .376
Overall Function Check ....................................... .377
Diagnostic Procedure .......................................... .378
DTC P0441 EVAP CONTROL SYSTEM ................ .382
System Description .............................................. .382
On Board Diagnosis Logic ................................... .382
DTC Confirmation Procedure .............................. .382
Overall Function Check ....................................... .383
Diagnostic Procedure .......................................... .384
DTC P0442 EVAP CONTROL SYSTEM ................ .387
On Board Diagnosis Logic ................................... .387
DTC Confirmation Procedure .............................. .388
Diagnostic Procedure .......................................... .389
DTC P0443 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE .............................. .396
Description ........................................................... .396
CONSULT-II Reference Value in Data Monitor Mode .396
On Board Diagnosis Logic ................................... .397
DTC Confirmation Procedure .............................. .397
Wiring Diagram .................................................... .398 Diagnostic Procedure ...........................................
.400
Component Inspection ......................................... .403
Removal and Installation ...................................... .403
DTC P0444, P0445 EVAP CANISTER PURGE VOL-
UME CONTROL SOLENOID VALVE ..................... .404
Description ........................................................... .404
CONSULT-II Reference Value in Data Monitor Mode .404
On Board Diagnosis Logic ................................... .405
DTC Confirmation Procedure ............................... .405
Wiring Diagram .................................................... .406
Diagnostic Procedure ........................................... .408
Component Inspection ......................................... .409
Removal and Installation ...................................... .410
DTC P0447 EVAP CANISTER VENT CONTROL
VALVE ..................................................................... .411
Component Description ....................................... .411
CONSULT-II Reference Value in Data Monitor Mode .411
On Board Diagnosis Logic ................................... .411
DTC Confirmation Procedure ............................... .412
Wiring Diagram .................................................... .413
Diagnostic Procedure ........................................... .414
Component Inspection ......................................... .416
DTC P0448 EVAP CANISTER VENT CONTROL
VALVE ..................................................................... .418
Component Description ....................................... .418
CONSULT-II Reference Value in Data Monitor Mode .418
On Board Diagnosis Logic ................................... .418
DTC Confirmation Procedure ............................... .419
Wiring Diagram .................................................... .420
Diagnostic Procedure ........................................... .421
Component Inspection ......................................... .422
DTC P0451 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .424
Component Description ....................................... .424
CONSULT-II Reference Value in Data Monitor Mode .424
On Board Diagnosis Logic ................................... .424
DTC Confirmation Procedure ............................... .425
Diagnostic Procedure ........................................... .425
Component Inspection ......................................... .426
DTC P0452 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .427
Component Description ....................................... .427
CONSULT-II Reference Value in Data Monitor Mode .427
On Board Diagnosis Logic ................................... .427
DTC Confirmation Procedure ............................... .428
Wiring Diagram .................................................... .429
Diagnostic Procedure ........................................... .430
Component Inspection ......................................... .432
DTC P0453 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .433
Component Description ....................................... .433
CONSULT-II Reference Value in Data Monitor Mode .433
On Board Diagnosis Logic ................................... .433