sensor INFINITI FX35 2007 Service Manual

INDEX FOR DTC EC-19
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
Alphabetical IndexNBS003KV
NOTE:

If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-155, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .

If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010.
Refer to EC-158, "
DTC U1010 CAN COMMUNICATION" .
Items
(CONSULT-II screen terms) DTC*
1
Reference page
CONSULT-II
GST*
2ECM*3
A/F SEN1 HTR (B1) P0031 0031 EC-164
A/F SEN1 HTR (B1) P0032 0032EC-164
A/F SEN1 HTR (B2) P0051 0051EC-164
A/F SEN1 HTR (B2) P0052 0052EC-164
A/F SENSOR1 (B1) P0130 0130EC-229
A/F SENSOR1 (B1) P0131 0131EC-239
A/F SENSOR1 (B1) P0132 0132EC-248
A/F SENSOR1 (B1) P0133 0133EC-257
A/F SENSOR1 (B1) P2A00 2A00EC-605
A/F SENSOR1 (B2) P0150 0150EC-229
A/F SENSOR1 (B2) P0151 0151EC-239
A/F SENSOR1 (B2) P0152 0152EC-248
A/F SENSOR1 (B2) P0153 0153EC-257
A/F SENSOR1 (B2) P2A03 2A03EC-605
A/T INTERLOCK P1730 1730 AT- 1 4 1
A/T TCC S/V FNCTN P0744 0744AT- 1 2 7
APP SEN 1/CIRC P2122 2122EC-576
APP SEN 1/CIRC P2123 2123EC-576
APP SEN 2/CIRC P2127 2127EC-583
APP SEN 2/CIRC P2128 2128EC-583
APP SENSOR P2138 2138EC-597
ASCD BRAKE SW P1572 1572 EC-530 (Models with ICC),
EC-539
(Models with ASCD)
ASCD SW P1564 1564 EC-515
(Models with ICC),
EC-522
(Models with ASCD)
ASCD VHL SPD SEN P1574 1574 EC-547
(Models with ICC),
EC-549
(Models with ASCD)
ATF TEMP SEN/CIRC P0710 0710 AT- 1 3 4
BRAKE SW/CIRCUIT P1805 1805EC-552
CAN COMM CIRCUIT U1000
1000*4EC-155
CAN COMM CIRCUIT U10011001*4EC-155
CKP SEN/CIRCUIT P0335 0335 EC-360
CLOSED LOOP-B1 P1148 1148EC-493
CLOSED LOOP-B2 P1168 1168EC-493
CMP SEN/CIRC-B1 P0340 0340EC-367
CMP SEN/CIRC-B2 P0345 0345EC-367
COLD START CONTROL P1421 1421EC-513
CONTROL UNIT(CAN) U1010 1010EC-158

EC-20
[VQ35DE]
INDEX FOR DTC
Revision: 2006 July 2007 FX35/FX45
CTP LEARNING P1225 1225 EC-509
CTP LEARNING P1226 1226 EC-511
CYL 1 MISFIRE P0301 0301EC-345
CYL 2 MISFIRE P0302 0302EC-345
CYL 3 MISFIRE P0303 0303EC-345
CYL 4 MISFIRE P0304 0304EC-345
CYL 5 MISFIRE P0305 0305EC-345
CYL 6 MISFIRE P0306 0306EC-345
D/C SOLENOID FNCTN P1764 1764 AT-156
D/C SOLENOID/CIRC P1762 1762AT-154
ECM P0605 0605EC-480
ECM BACK UP/CIRCUIT P0603 0603EC-476
ECT SEN/CIRC P0117 0117EC-209
ECT SEN/CIRC P0118 0118EC-209
ECT SENSOR P0125 0125EC-221
ENG OVER TEMP P1217 1217EC-496
ETC ACTR P2119 2119EC-574
ETC FUNCTION/CIRC P2101 2101EC-563
ETC MOT P2118 2118EC-569
ETC MOT PWR P2100 2100EC-557
ETC MOT PWR P2103 2103EC-557
EVAP GROSS LEAK P0455 0455EC-441
EVAP PURG FLOW/MON P0441 0441EC-382
EVAP SMALL LEAK P0442 0442EC-387
EVAP SYS PRES SEN P0451 0451EC-424
EVAP SYS PRES SEN P0452 0452EC-427
EVAP SYS PRES SEN P0453 0453EC-433
EVAP VERY SML LEAK P0456 0456EC-449
FR/B SOLENOID FNCT P1759 1759 AT-152
FR/B SOLENOID/CIRC P1757 1757AT-150
FTT SEN/CIRCUIT P0182 0182EC-333
FTT SEN/CIRCUIT P0183 0183EC-333
FTT SENSOR P0181 0181EC-327
FUEL LEV SEN SLOSH P0460 0460EC-459
FUEL LEVEL SENSOR P0461 0461EC-461
FUEL LEVL SEN/CIRC P0462 0462EC-463
FUEL LEVL SEN/CIRC P0463 0463EC-463
FUEL SYS-LEAN-B1 P0171 0171EC-304
FUEL SYS-LEAN-B2 P0174 0174EC-304
FUEL SYS-RICH-B1 P0172 0172EC-316
FUEL SYS-RICH-B2 P0175 0175EC-316
HLR/C SOL FNCTN P1769 1769 AT-160
Items
(CONSULT-II screen terms) DTC*
1
Reference page
CONSULT-II
GST*
2ECM*3

INDEX FOR DTC EC-21
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45HLR/C SOL/CIRC P1767 1767 AT- 1 5 8
HO2S2 (B1) P0137 0137EC-269
HO2S2 (B1) P0138 0138EC-280
HO2S2 (B1) P0139 0139EC-293
HO2S2 (B2) P0157 0157EC-269
HO2S2 (B2) P0158 0158EC-280
HO2S2 (B2) P0159 0159EC-293
HO2S2 HTR (B1) P0037 0037EC-172
HO2S2 HTR (B1) P0038 0038EC-172
HO2S2 HTR (B2) P0057 0057EC-172
HO2S2 HTR (B2) P0058 0058EC-172
I/C SOLENOID FNCTN P1754 1754 AT- 1 4 8
I/C SOLENOID/CIRC P1752 1752AT- 1 4 6
IAT SEN/CIRCUIT P0112 0112EC-204
IAT SEN/CIRCUIT P0113 0113EC-204
IAT SENSOR P0127 0127EC-224
ICC COMMAND VALUE*6P1568 1568EC-529
IN PULY SPEED P1715 1715 EC-551
INT/V TIM CONT-B1 P0011 0011EC-160
INT/V TIM CONT-B2 P0021 0021EC-160
INT/V TIM V/CIR-B1 P0075 0075EC-180
INT/V TIM V/CIR-B2 P0081 0081EC-180
ISC SYSTEM P0506 0506EC-467
ISC SYSTEM P0507 0507EC-469
KNOCK SEN/CIRC-B1 P0327 0327EC-355
KNOCK SEN/CIRC-B1 P0328 0328EC-355
L/PRESS SOL/CIRC P0745 0745 AT- 1 2 9
LC/B SOLENOID FNCT P1774 1774AT- 1 6 4
LC/B SOLENOID/CIRC P1772 1772AT- 1 6 2
MAF SEN/CIRCUIT P0101 0101EC-187
MAF SEN/CIRCUIT P0102 0102EC-196
MAF SEN/CIRCUIT P0103 0103EC-196
MULTI CYL MISFIRE P0300 0300EC-345
NATS MALFUNCTION P1610 - P1615 1610 - 1615 EC-52
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED. P0000 0000 —
P-N POS SW/CIRCUIT P0850 0850 EC-488
PNP SW/CIRC P0705 0705 AT- 11 2
PURG VOLUME CONT/V P0443 0443EC-396
PURG VOLUME CONT/V P0444 0444EC-404
PURG VOLUME CONT/V P0445 0445EC-404
PW ST P SEN/CIRC P0550 0550EC-471
Items
(CONSULT-II screen terms) DTC*
1
Reference page
CONSULT-II
GST*
2ECM*3

EC-22
[VQ35DE]
INDEX FOR DTC
Revision: 2006 July 2007 FX35/FX45
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-II.
*5: When the fail-safe operations for both self-diagnoses occur, the MIL illuminates.
*6: For models with ICC system. SENSOR POWER/CIRC P0643 0643
EC-483
TCC SOLENOID/CIRC P0740 0740 AT-125
TCM P0700 0700 AT- 111
TCS C/U FUNCTN P1211 1211EC-494
TCS/CIRC P1212 1212EC-495
THERMSTAT FNCTN P0128 0128EC-227
TP SEN 1/CIRC P0222 0222EC-338
TP SEN 1/CIRC P0223 0223EC-338
TP SEN 2/CIRC P0122 0122EC-214
TP SEN 2/CIRC P0123 0123EC-214
TP SENSOR P2135 2135EC-590
TURBINE SENSOR P0717 0717 AT- 11 6
TW CATALYST SYS-B1 P0420 0420EC-376
TW CATALYST SYS-B2 P0430 0430EC-376
VEH SPD SEN/CIR AT*5P0720 0720AT- 11 8
VEH SPEED SEN/CIRC*5P0500 0500EC-465
VENT CONTROL VALVE P0447 0447 EC-411
VENT CONTROL VALVE P0448 0448EC-418
Items
(CONSULT-II screen terms) DTC*
1
Reference page
CONSULT-II
GST*
2ECM*3

PRECAUTIONS EC-23
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NBS003KW
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Procedures without Cowl Top CoverNBS006SD
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
On Board Diagnostic (OBD) System of Engine and A/TNBS003KX
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:

Be sure to turn the ignition switch OFF and disconnect the negative battery cable before any
repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves,
etc. will cause the MIL to light up.

Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to the open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)

Certain systems and components, especially those related to OBD, may use a new style slide-
locking type harness connector. For description and how to disconnect, refer to PG-71, "
HAR-
NESS CONNECTOR" .

Be sure to route and secure the harnesses properly after work. The interference of the harness
with a bracket, etc. may cause the MIL to light up due to the short circuit.

Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to the malfunction of the EVAP system or fuel injection system,
etc.

Be sure to erase the unnecessary malfunction information (repairs completed) from the ECM and
TCM (Transmission control module) before returning the vehicle to the customer.
PIIB3706J

PRECAUTIONS EC-25
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45

Before replacing ECM, perform “ECM Terminals and Refer-
ence Value” inspection and make sure ECM functions prop-
erly. Refer to EC-109, "
ECM Terminals and Reference Value"
.

Handle mass air flow sensor carefully to avoid damage.

Do not disassemble mass air flow sensor.

Do not clean mass air flow sensor with any type of deter-
gent.

Do not disassemble electric throttle control actuator.

Even a slight leak in the air intake system can cause seri-
ous incidents.

Do not shock or jar the camshaft position sensor (PHASE), crankshaft position sensor (POS).

After performing each TROUBLE DIAGNOSIS, perform DTC
Confirmation Procedure or Overall Function Check.
The DTC should not be displayed in the DTC Confirmation
Procedure if the repair is completed. The Overall Function
Check should be a good result if the repair is completed.

When measuring ECM signals with a circuit tester, never
allow the two tester probes to contact.
Accidental contact of probes will cause a short circuit and
damage the ECM power transistor.

Do not use ECM ground terminals when measuring input/
output voltage. Doing so may result in damage to the ECM's
transistor. Use a ground other than ECM terminals, such as
the ground.
MEF040D
SEF217U
SEF348N

PREPARATION EC-27
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
PREPARATIONPFP:00002
Special Service ToolsNBS003KZ
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name Description
KV10117100
(J-36471-A)
Heated oxygen
sensor wrench Loosening or tightening heated oxygen sensor
with 22 mm (0.87 in) hexagon nut
KV10114400
(J-38365)
Heated oxygen
sensor wrench Loosening or tightening air fuel ratio (A/F) sensor
a: 22 mm (0.87 in)
(J-44321)
Fuel pressure gauge
kit Checking fuel pressure
(J-44321-6)
Fuel pressure adapter Connecting fuel pressure gauge to quick
connector type fuel lines.
(J-44626)
Air fuel ratio (A/F)
sensor wrench Loosening or tightening air fuel ratio (A/F) sensor
1
(J-45488)
Quick connector
release Remove fuel tube quick connectors in engine
room.
S-NT379
S-NT636
LEC642
LBIA0376E
LEM054
PBIC0198E

EC-28
[VQ35DE]
PREPARATION
Revision: 2006 July 2007 FX35/FX45
Commercial Service ToolsNBS003L0
Tool name
(Kent-Moore No.) Description
Leak detector
i.e.: (J-41416) Locating EVAP leak
EVAP service port
adapter
i.e.: (J-41413-OBD) Applying positive pressure through EVAP service
port
Fuel filler cap adapter
i.e.: (MLR-8382) Checking fuel tank vacuum relief valve opening
pressure
Socket wrench Removing and installing engine coolant temperature sensor
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12) Reconditioning the exhaust system threads
before installing a new oxygen sensor. Use with
anti-seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for
Zirconia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for
Titania Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL
specification MIL-A-
907) Lubricating oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
S-NT703
S-NT704
S-NT815
S-NT705
AEM488
S-NT779

EC-30
[VQ35DE]
ENGINE CONTROL SYSTEM
Revision: 2006 July 2007 FX35/FX45
Multiport Fuel Injection (MFI) SystemNBS003L2
INPUT/OUTPUT SIGNAL CHART
*1: This sensor is not used to control the engine system under normal conditions.
*2: This signal is sent to the ECM through CAN communication line.
*3: ECM determines the start signal status by the signals of engine speed and battery voltage.
SYSTEM DESCRIPTION
The amount of fuel injected from the fuel injector is determined by the ECM. The ECM controls the length of
time the valve remains open (injection pulse duration). The amount of fuel injected is a program value in the
ECM memory. The program value is preset by engine operating conditions. These conditions are determined
by input signals (for engine speed and intake air) from both the crankshaft position sensor and the mass air
flow sensor.
VARIOUS FUEL INJECTION INCREASE/DECREASE COMPENSATION
In addition, the amount of fuel injected is compensated to improve engine performance under various operat-
ing conditions as listed below.
<Fuel increase>

During warm-up

When starting the engine

During acceleration

Hot-engine operation

When selector lever is changed from N to D

High-load, high-speed operation
<Fuel decrease>

During deceleration

During high engine speed operation
Sensor Input Signal to ECM ECM function Actuator
Crankshaft position sensor (POS) Engine speed*
3
Piston position
Fuel injection
& mixture ratio
control Fuel injector
Camshaft position sensor (PHASE)
Mass air flow sensor Amount of intake air
Engine coolant temperature sensor Engine coolant temperature
Air fuel ratio (A/F) sensor 1 Density of oxygen in exhaust gas
Throttle position sensor Throttle position
Accelerator pedal position sensor Accelerator pedal position
Park/neutral position (PNP) switch Gear position
Knock sensor Engine knocking condition
Battery Battery voltage*
3
Power steering pressure sensor Power steering operation
Heated oxygen sensor 2*
1Density of oxygen in exhaust gas
Air conditioner switch Air conditioner operation*
2
Wheel sensorVehicle speed*2

ENGINE CONTROL SYSTEM EC-31
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2006 July 2007 FX35/FX45
MIXTURE RATIO FEEDBACK CONTROL (CLOSED LOOP CONTROL)
The mixture ratio feedback system provides the best air-fuel mixture ratio for driveability and emission control.
The three way catalyst 1 can then better reduce CO, HC and NOx emissions. This system uses air fuel ratio
(A/F) sensor 1 in the exhaust manifold to monitor whether the engine operation is rich or lean. The ECM
adjusts the injection pulse width according to the sensor voltage signal. For more information about air fuel
ratio (A/F) sensor 1, refer to EC-239, "
DTC P0131, P0151 A/F SENSOR 1" . This maintains the mixture ratio
within the range of stoichiometric (ideal air-fuel mixture).
This stage is referred to as the closed loop control condition.
Heated oxygen sensor 2 is located downstream of the three way catalyst 1. Even if the switching characteris-
tics of air fuel ratio (A/F) sensor 1 shift, the air-fuel ratio is controlled to stoichiometric by the signal from
heated oxygen sensor 2.
Open Loop Control
The open loop system condition refers to when the ECM detects any of the following conditions. Feedback
control stops in order to maintain stabilized fuel combustion.

Deceleration and acceleration

High-load, high-speed operation

Malfunction of air fuel ratio (A/F) sensor 1 or its circuit

Insufficient activation of air fuel ratio (A/F) sensor 1 at low engine coolant temperature

High engine coolant temperature

During warm-up

After shifting from N to D

When starting the engine
MIXTURE RATIO SELF-LEARNING CONTROL
The mixture ratio feedback control system monitors the mixture ratio signal transmitted from air fuel ratio (A/F)
sensor 1. This feedback signal is then sent to the ECM. The ECM controls the basic mixture ratio as close to
the theoretical mixture ratio as possible. However, the basic mixture ratio is not necessarily controlled as orig-
inally designed. Both manufacturing differences (i.e., mass air flow sensor hot wire) and characteristic
changes during operation (i.e., fuel injector clogging) directly affect mixture ratio.
Accordingly, the difference between the basic and theoretical mixture ratios is monitored in this system. This is
then computed in terms of “injection pulse duration” to automatically compensate for the difference between
the two ratios.
“Fuel trim” refers to the feedback compensation value compared against the basic injection duration. Fuel trim
includes short term fuel trim and long term fuel trim.
“Short term fuel trim” is the short-term fuel compensation used to maintain the mixture ratio at its theoretical
value. The signal from air fuel ratio (A/F) sensor 1 indicates whether the mixture ratio is RICH or LEAN com-
pared to the theoretical value. The signal then triggers a reduction in fuel volume if the mixture ratio is rich, and
an increase in fuel volume if it is lean.
“Long term fuel trim” is overall fuel compensation carried out long-term to compensate for continual deviation
of the short term fuel trim from the central value. Such deviation will occur due to individual engine differences,
wear over time and changes in the usage environment.
PBIB3020E