INFINITI JX 2013 Owner's Manual

THE BSW AND BSI SYSTEMS:
The Blind Spot Warning (BSW) and Blind Spot
Intervention (BSI) systems can help alert the
driver of other vehicles in adjacent lanes when
changing lanes.
The BSW system uses radar sensors
2in-
stalled near the rear bumper to detect other ve-
hicles beside your vehicle in an adjacent lane. In
addition to the radar sensors, the BSI system
uses a camera
1installed behind the windshield
to monitor the lane markers of your traveling lane. The radar sensors can detect vehicles on either
side of your vehicle within the detection zone
shown as illustrated. This detection zone starts
from the outside mirror of your vehicle and ex-
tends approximately 10 ft (3.0 m) behind the rear
bumper, and approximately 10 ft (3.0 m) side-
ways.
The BSW system operates above approximately
20 MPH (32 km/h). If the radar sensors detects
vehicles in the detection zone, the Blind spot
warning indicator light illuminates. If the driver
then activates the turn signal, the system chimes
a sound (twice) and the Blind spot warning indi-
cator light will flash.The BSI system operates above approximately
37 MPH (60 km/h). If the radar detects a vehicle
in the detection zone and your vehicle is ap-
proaching the lane marker, the system chime a
sound (three times) , the Blind spot warning indi-
cator light and slightly applies the brakes for a
moment on one side to help return the vehicle
back to the traveling lane.
LSD2018
Detection zone
SSD1030
5-32Starting and driving

THE BCI SYSTEM
The BCI systems can help alert the driver of
approaching vehicles or rear objects when the
driver is backing out of a parking space.
When the shift position is R (Reverse) and the
vehicle speed is less than approximately 5 MPH
(8 km/h), the BCI system operates.The BCI system uses radar sensors
1installed
on both sides near the rear bumper to detect an
approaching vehicle and sonar sensors to detect
objects in the rear.
The radar sensors
1detects the approaching
vehicle from up to approximately 15 m (49 ft.)
away. The sonar sensors
2and detect a rear
obstacle at up to approximately 4.9 feet (1.5 m)
3. If the radar detects a vehicle approaching from
the side or the sonar detects close objects in the
rear, the system gives visual and audible warn-
ings, and applies the brake for a moment when
the vehicle is moving backwards. After the auto-
matic brake application, the driver must depress
the brake pedal to maintain brake pressure. If the
driver’s foot is on the accelerator pedal, the sys-
tem pushes the accelerator upward before apply-
ing the brake. If you continue to press the accel-
erator, the system will not engage the brake.
LSD2025LSD2026LSD2042
Starting and driving5-33

WARNING
●The BSW and BSI systems are not a
replacement for proper driving proce-
dure and are not designed to prevent
contact with vehicles or objects. When
changing lanes, always use the side and
rear mirrors and turn and look in the
direction you will move to ensure it is
safe to change lanes. Never rely solely
on the BSW or BSI system.
● The BCI system is not a replacement for
proper driving procedure and is not de-
signed to prevent contact with vehicles
or objects. When backing out of parking
space, always use the side and rear
mirrors and turn and look in the direc-
tion you will move. Never rely solely on
the BCI system.
● There is a limitation to the detection
capability of the radar or the sonar. Us-
ing the BSI and BCI systems under
some road, ground, lane marker, traffic
or weather conditions could lead to im-
proper system operation. Always rely
on your own operation to avoid
accidents.
BSW SYSTEM OPERATION
If the radar sensors detect vehicles in the detec-
tion zone, the Blind spot warning indicator light
located inside the outside mirrors illuminates. If
the turn signal is then activated, the system
chimes a sound (twice) and the Blind spot warn-
ing indicator light flashes. The Blind spot warning
indicator light continues to flash until the de-
tected vehicles leave the detection zone.
The Blind spot warning indicator lights illuminate
for a few seconds when the ignition switch is
placed in the ON position. The brightness of the Blind spot warning indica-
tor lights is adjusted automatically depending on
the brightness of the ambient light.
A chime sounds if the radar sensors have already
detected vehicles when the driver activates the
turn signal. If a vehicle comes into the detection
zone after the driver activates the turn signal, then
only the Blind spot system indicator light flashes
and no chime sounds. See “BSW/BSI driving
situations” in this section.
LSD2053
5-34Starting and driving

The BSW system automatically turns on every
time the engine is started, as long as it is acti-
vated using the settings menu on the meter dis-
play.
When the warning systems switch is turned off,
the indicator
1on the switch is off. The indicator
will also be off if the BSW, the Lane Departure
Warning (LDW) and the Forward Collision Warn-
ing (FCW) systems are deactivated.
How to enable/disable the BSW
system
Perform the following steps to enable or disable
the BSW system. 1. Press the
button until “Settings” dis-
plays in the vehicle information display. Use
the
to select “Driver Assistance”.
Then press the ENTER button.
2. Select “Driver Aids”, and press the ENTER button.
3. To set the BSW system to on or off, use the
buttons to navigate in the menu
and use the ENTER button to select or
change an item:
● Select “Blind Spot” and press the ENTER
button.
– To turn on the warning, use the ENTER button to check box for “Warning (BSW)”
– To turn on the system, use the ENTER button to check box for “Assistance
(BSI)”
– Use the ENTER button to toggle through the brightness choices — “Bright / STD
/Dark”
BSW temporarily not available
When the “Unavailable Side Radar Obstruction”
message will appear in the meter display, a chime
will sound, the warning systems switch indicator
will blink and the BSW system will be not avail-
able. When the above condition no longer exist, the
BSW system will resume automatically. For addi-
tional information, see “Side radar maintenance”
in this section.
BSW malfunction
When the BSW system malfunctions, the system
will turn off automatically, a chime will sound and
the “Please see owner’s manual” will appear in
the meter display.
Action to take:
Stop the vehicle in a safe location, turn the engine
off and restart the engine. If the message contin-
ues to appear, have the system checked by an
INFINITI retailer.
LSD2015
Starting and driving5-35

BSI SYSTEM OPERATION
If the radar sensors detect vehicles in the detec-
tion zone, the Blind spot warning indicator light
located near the outside mirrors illuminates. If
your vehicle is approaching a lane marker, the
system chimes a sound (three times) and the
Blind spot warning indicator light flashes. Then
the system applies the brakes on one side of the
vehicle for a moment to help return the vehicle
back to the center of the lane. BSI operates
regardless of turn signal usage.NOTE:
Warning and brake control will only be
activated if the Blind spot warning indica-
tor light is already illuminated when your
vehicle approaches a lane marker. If an-
other vehicle comes into the detection
zone after your vehicle has crossed a lane
marker, no warning or brake control will be
activated. For additional information see
“BSW/BSI driving situations” in this sec-
tion. The BSI system is typically activated
earlier than the Lane Departure Prevention
(LDP) system when your vehicle is ap-
proaching a lane marker.
The BSI system turns on when the dynamic driver
assistance switch on the steering wheel is
pushed when the “Blind Spot Intervention” is
enabled in the settings menu on the meter dis-
play. The BSI ON indicator light (green) on the
instrument panel illuminates when the BSI sys-
tem is turned on.
The BSI system provides a chime and turns on or
flashes the Blind spot warning indicator light
even if the BSW system is off.
How to enable/disable the BSI system
Perform the following steps to enable or disable
the BSI system.
LSD2053SSD1029
5-36Starting and driving

1. Press thebutton until “Settings” dis-
plays in the vehicle information display. Use
the
to select “Driver Assistance”.
Then press the ENTER button.
2. Select “Driver Aids”, and press the ENTER button.
3. To set the BSI system to on or off, use the
buttons to navigate in the menu
and use the ENTER button to select or
change an item:
● Select “Blind Spot” and press the ENTER
button. – To turn on the warning, use the ENTER
button to check box for “Warning (BSW)”
– To turn on the system, use the ENTER button to check box for “Assistance
(BSI)”
– Use the ENTER button to toggle through the brightness choices — “Bright / STD
/Dark”
BSI temporarily not available
When any of the following messages appear on
the meter display, a chime will sound and the BSI
system will be turned off automatically.
● “Unavailable Road is slippery” :
When the VDC system (except traction con-
trol system function) or ABS operates.
● “Unavailable VDC OFF” :
When the VDC system is turned off.
● “Unavailable Snow mode active” :
When the drive mode select switch is turned
to the SNOW mode.
● “Unavailable High Cabin Temp. ” :
When the camera detects that the interior
temperature is high (over approximately
104°F (40°C)) .
● “Unavailable Side Radar Obstruction” :
When side radar blockage is detected. Turn off the BSI system and turn it on again when
the above conditions no longer exist.
BSI malfunction
When the BSI system malfunctions, it will be
turned off automatically, a chime will sound and
the BSI system warning light (orange) will illumi-
nate.
Action to take:
Stop the vehicle in a safe location, turn the engine
off and restart the engine. If the warning light
(orange) continues to illuminate, have the system
checked by an INFINITI retailer.
SSD0938
Starting and driving5-37

BCI SYSTEM OPERATION
WARNING
The radar sensors may not be able to
detect certain objects such as:– Pedestrians, bicycles, animals
– A vehicle that passing at speeds
greater than approximately 15 MPH
(24 km/h) The radar sensors may not detect ap-
proaching vehicles in certain situations:
– When the vehicle parked aside ob- struct the beam of the radar sensor.
– When the vehicle is parked in an angled parking space.
– When the vehicle is parked on the inclined ground.
– When the vehicle turns around into your vehicle’s aisle.
– When the angle formed by your ve- hicle and approaching vehicle is
small
Severe weather or road spray conditions
may reduce the ability of the radar to de-
tect other vehicles.
The sonar sensor may not detect: – Small or moving objects
– Wedge-shaped objects
– Object close to the bumper (less than approximately 1 ft. (30 cm)) - Thin
objects such as rope, wire and chain,
etc.
LSD2052
5-38Starting and driving

The brake engagement by the BCI system
is not as effective on a slope, as it is on flat
ground. When on a steep slope, the sys-
tem may not function properly.
Do not use the BCI systems under the
following conditions because the system
may not function properly.– When driving with a tire that is not within normal tire conditions (e.g.
tire wear, low tire pressure, installa-
tion of spare tire, tire chains, non-
standard wheels) .
– When the vehicle is equipped with non-original brake parts or suspen-
sion parts.
Do not use the BCI systems when towing a
trailer.
Excessive noise (e.g. audio system vol-
ume, open vehicle window) will interfere
with the chime sound, and it may not be
heard.
When the shift selector is placed in R (Reverse)
position, the BCI ON appears in the meter dis-
play. If the radar detects an approaching vehicle from
the side, the system chimes a sound (single
beep) , the Blind spot warning indicator light on
the side the approaching vehicle flashes and a
yellow rectangular frame appears in the display.
NOTE:
● In the case of several vehicles approaching
in a row or in the opposite direction, a chime
may not be issued to the BCI system after
the first vehicle passes the sensors.
● When the sonar system sounds a tone, the
BCI system does not chime this sound
(single beep) .
LSD2027LSD2043
Starting and driving5-39

A red frame will appear in the center display, the
system will chime 3 times and the brakes will be
applied for a moment, if an approaching vehicle is
detected when your vehicle is backing up. After
the automatic brake application, the driver must
depress the brake pedal to maintain brake pres-
sure.
If the driver’s foot is on the accelerator pedal, the
system moves the accelerator pedal upward be-
fore the braking is applied. If you continue to
press the accelerator, the system will not engage
the brakes.NOTE:
The system does not operate if the object is
very close to the bumper.
The BCI system automatically turns on every time
the engine is started.
The BCI system is turned off temporarily by push-
ing the BCI switch. The BCI OFF display appears
on the meter display. When the shift selector is
placed to the R (Reverse) position again the BCI
system is turned on.
The BCI system can be turned off permanently by
setting in the meter display.
1. Press the
button until “Settings” dis-
plays in the vehicle information display. Use
the
to select “Driver Assistance”.
Then press the ENTER button.
LSD2044LSD2045LSD2030
5-40Starting and driving

2. Select “Back-up Collision Interv.”, and pressthe ENTER button.
3. To set the BCI system to on or off, use the
buttons to navigate in the menu
and use the ENTER button to select or
change an item.
BCI temporarily not available
When the following message is appeared on the
meter display, a chime will sound, the BCI system
will be turned off automatically.
● “Unavailable High Accelarator Temp. ” :
When the accelerator pedal actuator de-
tects that the internal motor temperature is
high (over approximately 212°F (100°C)) .
● “Unavailable Side Radar Obstruction” :
When side radar blockage is detected.
Turn off the BCI system and turn it on again when
the above conditions no longer exist.
BCI malfunction
When the BCI system malfunction, they will be
turned off automatically, a chime will sound and
the BCI system warning light (orange) will illumi-
nate.
Action to take:
Stop the vehicle in a safe location, turn the engine
off and restart the engine. If the warning light
(orange) continues to illuminate, have the system
checked by an INFINITI retailer.
BSW/BSI DRIVING SITUATIONS
Another vehicle approaching from
behind
LSD2046SSD1026
Starting and driving5-41