brake sensor INFINITI M35 2007 Factory Service Manual

TROUBLE DIAGNOSIS
LAN-57
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: 2007 April2007 M35/M45

*1: Models with adaptive front-lighting system

*2: Models with lane departure warning

*3: Models with ICC system Seat belt buckle switch signal R T
Target A/C evaporator temperature signal R T
Vehicle speed signalRRRRRRT RRR
RRRRR TR
Steering angle sensor signal R T R
Tire pressure data signal R T
Tire pressure signalRR T
TR
A/T shift schedule change demand signal R T
ABS malfunction signalTR
ABS operation signal TR
ABS warning lamp signal R T
Brake pressure control signalTR
Brake warning lamp signal R T
Side G sensor signal R T
SLIP indicator lamp signal R T
TCS malfunction signalTR
TCS operation signal TR
VDC malfunction signalTR
VDC OFF indicator lamp signal R T
VDC OFF switch signalTR
VDC operation signalTR
Deceleration degree commandment value signalRT
ICC OD cancel request signal R T
ICC operation signal R T
ICC warning lamp signalRT
Front wiper stop position signal R T
High beam status signal RT
Hood switch signal R T
Low beam status signal R R T
Rear window defogger control signal R R T
Starter relay status signal R TSignals
ECM
4WD
AFS
*1
BCM
LANE
*2
TCM
AV
I-KEY
M&A
STRG
TPMS
PSB
ADP
ABS
ICC
*3
IPDM-E

LT-2Revision: 2007 April2007 M35/M45 ACTIVE TEST ..................................................... 58
CONSULT-II Functions (IPDM E/R) ........................ 59
CONSULT-II BASIC OPERATION ....................... 59
DATA MONITOR .................................................. 59
ACTIVE TEST ..................................................... 59
Headlamp High Beam Does Not Illuminate (Both
Sides) ..................................................................... 60
Headlamp High Beam Does Not Illuminate (One
Side) ....................................................................... 63
High Beam Indicator Lamp Does Not Illuminate ..... 64
Headlamp Low Beam Does Not Illuminate (Both
Sides) ..................................................................... 65
Headlamp Low Beam Does Not Illuminate (One
Side) ....................................................................... 68
Headlamps Do Not Turn OFF ................................. 70
General Information for Xenon Headlamp Trouble
Diagnosis ................................................................ 71
Caution: .................................................................. 71
Xenon Headlamp Trouble Diagnosis ...................... 71
Aiming Adjustment .................................................. 72
PREPARATION BEFORE ADJUSTING .............. 72
LOW BEAM AND HIGH BEAM ........................... 72
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 73
Bulb Replacement .................................................. 73
HEADLAMP (INNER) HIGH BEAM ..................... 73
HEADLAMP (OUTER) LOW BEAM .................... 74
PARKING LAMP .................................................. 74
FRONT TURN SIGNAL LAMP ............................ 74
FRONT SIDE MARKER LAMP ............................ 74
Removal and Installation ........................................ 75
REMOVAL ........................................................... 75
INSTALLATION .................................................... 75
Disassembly and Assembly .................................... 76
DISASSEMBLY ................................................... 76
ASSEMBLY ......................................................... 77
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM - .................................................................. 78
Component Parts and Harness Connector Location ... 78
System Description ................................................. 78
OUTLINE ............................................................. 79
HEADLAMP OPERATION ................................... 80
DAYTIME LIGHT OPERATION ........................... 81
COMBINATION SWITCH READING FUNCTION ... 81
AUTO LIGHT OPERATION ................................. 81
CAN Communication System Description .............. 81
CAN Communication Unit ....................................... 81
Schematic ............................................................... 82
Wiring Diagram — DTRL — ................................... 83
Terminals and Reference Values for BCM .............. 89
Terminals and Reference Values for IPDM E/R ...... 91
How to Perform Trouble Diagnosis ......................... 91
Preliminary Check .................................................. 92
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT ............................................. 92
INSPECTION FOR PARKING BRAKE SWITCH
CIRCUIT .............................................................. 93
CONSULT-II Functions (BCM) ................................ 94
CONSULT-II BASIC OPERATION ....................... 94DATA MONITOR .................................................. 94
ACTIVE TEST ...................................................... 95
CONSULT-II Functions (IPDM E/R) ........................ 96
CONSULT-II BASIC OPERATION ....................... 96
DATA MONITOR .................................................. 96
ACTIVE TEST ...................................................... 96
Daytime Light Control Does Not Operate Properly
(Normal Headlamps Operate Properly) .................. 97
Headlamp High Beam Does Not Illuminate (Both
Sides) ....................................................................100
RH High Beam Does Not Illuminate But LH High
Beam Illuminates ..................................................104
LH High Beam Does Not Illuminate But RH High
Beam Illuminates ..................................................106
Headlamp Low Beam Does Not Illuminate (Both
Sides) ....................................................................108
Headlamp Low Beam Does Not Illuminate (One
Side) ...................................................................... 111
Headlamps Do Not Turn OFF ...............................113
General Information for Xenon Headlamp Trouble
Diagnosis ..............................................................114
CAUTION: .............................................................114
Xenon Headlamp Trouble Diagnosis ....................114
Aiming Adjustment ................................................114
Bulb Replacement .................................................114
Removal and Installation .......................................114
Disassembly and Assembly ..................................114
AUTO LIGHT SYSTEM ...........................................115
Component Parts and Harness Connector Location .115
System Description ...............................................115
OUTLINE ...........................................................115
COMBINATION SWITCH READING FUNCTION .116
EXTERIOR LAMP BATTERY SAVER CONTROL .116
DELAY TIMER FUNCTION ................................116
CAN Communication System Description ............116
CAN Communication Unit .....................................116
Major Components and Functions ........................116
Schematic .............................................................117
Wiring Diagram — AUTO/L — ..............................118
Terminals and Reference Values for BCM ............124
Terminals and Reference Values for IPDM E/R ....126
How to Perform Trouble Diagnoses ......................126
Preliminary Check .................................................127
SETTING CHANGE FUNCTIONS .....................127
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ...................................................................127
CONSULT-II Functions (BCM) ..............................128
CONSULT-II BASIC OPERATION .....................128
WORK SUPPORT .............................................128
DATA MONITOR ................................................129
ACTIVE TEST ....................................................130
Symptom Chart .....................................................130
Lighting Switch Inspection ....................................131
Optical Sensor System Inspection ........................131
Removal and Installation for Optical Sensor .........133
REMOVAL ..........................................................133
INSTALLATION ..................................................133
ACTIVE AFS ............................................................134
Component Parts and Harness Connector Location .134

HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -
LT-95
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2007 April2007 M35/M45
NOTE:
This item is displayed, but cannot be monitored.
ACTIVE TEST
Operation Procedure
1. Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2. Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3. Touch item to be tested and check operation of the selected item.
4. During the operation check, touching “BACK” deactivates the operation.
Display Item List
DOOR SW - AS “ON/OFF”Displays status of the passenger door as judged from the passenger door switch signal. (door
is open: ON/door is closed: OFF)
DOOR SW - RR “ON/OFF”Displays status of the rear door as judged from the rear door switch (RH) signal. (door is
open: ON/door is closed: OFF)
DOOR SW - RL “ON/OFF”Displays status of the rear door as judged from the rear door switch (LH) signal. (door is open:
ON/door is closed: OFF)
BACK DOOR SW
NOTE “OFF” —
PKB SW “ON/OFF”Displays status (parking brake released: ON/ parking brake applied: OFF) of parking brake
switch judged from parking brake switch signal.
ENGINE RUN “ON/OFF”Displays status (engine running: ON/ engine stopped: OFF) of engine judged from engine run
signal.
I - KEY LOCK “ON/OFF” Displays “locked (ON)/other (OFF)” status, determined from lock signal.
OPTICAL SENSOR “0 - 5V” Displays “outside brightness (close to 5 V when light/close to 0 V when dark)” judged from
optical sensor signal.
VEHICLE SPEED “km/h” Displays vehicle speed as judged from vehicle speed signal.Monitor item Contents
Test item Description
TAIL LAMP Allows tail lamp relay to operate by switching ON-OFF.
FR FOG LAMP Allows front fog lamp relay to operate by switching ON-OFF.
DAYTIME RUNNING LIGHT Allows daytime relay to operate by switching ON-OFF.
HEAD LAMP (HI, LO) Allows headlamp relay to operate by switching ON-OFF.

HARNESS
PG-95
C
D
E
F
G
H
I
J
L
MA
B
PG
Revision: 2007 April2007 M35/M45
Wiring Diagram Codes (Cell Codes) NKS004ET
Use the chart below to find out what each wiring diagram code stands for.
Refer to the wiring diagram code in the alphabetical index to find the location (page number) of each wiring
diagram.
Code Section Wiring Diagram Name
A/C ATC Air Conditioner
AF1B1 EC Air Fuel Ratio Sensor 1 Bank 1
AF1B2 EC Air Fuel Ratio Sensor 1 Bank 2
AF1HB1 EC Air Fuel Ratio Sensor 1 Heater Bank 1
AF1HB2 EC Air Fuel Ratio Sensor 1 Heater Bank 2
AFS LT Adaptive Front Lighting System
APPS1 EC Accelerator Pedal Position Sensor
APPS2 EC Accelerator Pedal Position Sensor
APPS3 EC Accelerator Pedal Position Sensor
ASC/BS EC Automatic Speed Control Device (ASCD) Brake Switch
ASC/SW EC Automatic Speed Control Device (ASCD) Steering Switch
ASCBOF EC Automatic Speed Control Device (ASCD) Brake Switch
ASCIND EC Automatic Speed Control Device (ASCD) Indicator
AT/IND DI A/T Indicator Lamp
AUT/DP SE Automatic Drive Positioner
AUTO/L LT Automatic Light System
AV AV Audio and Visual System
AWD TF AWD Control System
BACK/L LT Back-Up Lamp
BRK/SW EC Brake Switch
C/SEAT SE Climate Controlled Seat
CAN AT CAN Communication Line
CAN EC CAN Communication Line
CAN LAN CAN System
CHARGE SC Charging System
CHIME DI Warning Chime
CIGAR WW Cigarette Lighter
CLOCK DI Clock
COMBSW LT Combination Switch
COMPAS DI Compass and Thermometer
COOL/F EC Cooling Fan Control
CUR/SE EC Battery Current Sensor
D/LOCK BL Power Door Lock
DEF GW Rear Window Defogger
DTRL LT Headlamp - with Daytime Light System
ECM/PW EC ECM Power Supply for Back-Up
ECTS EC Engine Coolant Temperature Sensor
ENG/ST BL Engine Start System
EPS STC Electric Controlled Power Steering System
ETC1 EC Electric Throttle Control Function
ETC2 EC Electric Throttle Control Motor Relay

PG-96
HARNESS
Revision: 2007 April2007 M35/M45
ETC3 EC Electric Throttle Control Motor
F/FOG LT Front Fog Lamp
F/PUMP EC Fuel Pump
FPCM EC Fuel Pump Control Module
FTS AT A/T Fluid Temperature Sensor Circuit
FTTS EC Fuel Tank Temperature Sensor
FUELB1 EC Fuel Injection System Function (Bank 1)
FUELB2 EC Fuel Injection System Function (Bank 2)
H/LAMP LT Headlamp
HORN WW Horn
HSEAT SE Heated Seat
I/KEY BL Intelligent Key System
I/MIRR GW Inside Mirror (Auto Anti-Dazzling Mirror)
IATS EC Intake Air Temperature Sensor
ICC ACS Intelligent Cruise Control System
ICC/BS EC ICC Brake Switch
ICC/SW EC ICC Steering Switch
ICCBOF EC ICC Brake Switch
IGNSYS EC Ignition System
ILL LT Illumination
INJECT EC Injector
IVCB1 EC Intake Valve Timing Control Solenoid Valve Bank 1
IVCB2 EC Intake Valve Timing Control Solenoid Valve Bank 2
IVCSB1 EC Intake Valve Timing Control Position Sensor Bank 1
IVCSB2 EC Intake Valve Timing Control Position Sensor Bank 2
IVTB1 EC Intake Valve Timing Control System (Bank 1)
IVTB2 EC Intake Valve Timing Control System (Bank 2)
KS EC Knock Sensor
LDW DI Lane Departure Warning System
MAFS EC Mass Air Flow Sensor
MAIN AT Main Power Supply and Ground Circuit
MAIN EC Main Power Supply and Ground Circuit
METER DI Speedometer, Tachometer, Temp., Oil and Fuel Gauges
MIL/DL EC MIL & Data Link Connector
MIRROR GW Door Mirror
MMSW AT Manual Mode Switch
NATS BL Nissan Anti-Theft System
NONDTC AT Non-Detective Items
O2H2B1 EC Heated Oxygen Sensor 2 Heater Bank 1
O2H2B2 EC Heated Oxygen Sensor 2 Heater Bank 2
O2S2B1 EC Heated Oxygen Sensor 2 Bank 1
O2S2B2 EC Heated Oxygen Sensor 2 Bank 2
P/SCKT WW Power Socket
PDU PG Power Distribution Unit Code Section Wiring Diagram Name

RSU-8
REAR SUSPENSION ASSEMBLY
Revision: 2007 April2007 M35/M45
Removal and InstallationNES000J9
REMOVAL
1. Remove tires with a power tool.
2. Remove brake caliper with a power tool. Hang it in a place where it will not interfere with work. Refer to
BR-28, "
REAR DISC BRAKE" .
CAUTION:
Do not depressing brake pedal while brake caliper is removed.
3. Put matching marks on both disc rotor and the wheel hub and
bearing assembly, then remove disc rotor.
4. Remove rear under cover.
5. Remove wheel sensor from rear final drive.
6. Remove harness from rear final drive and rear suspension
member.
7. Remove center muffler. Refer to EX-3, "
EXHAUST SYSTEM" .
8. Remove rear propeller shaft. Refer to PR-6, "
REAR PROPEL-
LER SHAFT" .
9. Remove stabilizer bar. Refer to RSU-17, "
STABILIZER BAR" .
10. Remove parking brake cable mounting bolt and separate park-
ing brake cable from vehicle and rear suspension member. Refer to PB-4, "
PARKING BRAKE CONTROL"
.
11. Remove rear lower link and coil spring. Refer to RSU-16, "
REAR LOWER LINK & COIL SPRING" .
12. Remove mounting bolt on lower side of shock absorber. Refer to RSU-10, "
SHOCK ABSORBER" .
13. Set jack under rear final drive.
14. Remove member stay from vehicle.
15. Remove rear pin stay mounting bolts and nuts.
16. Gradually lowering jack, remove rear pin stay and rear suspension assembly.
INSTALLATION

Installation is the reverse order of the removal. For tightening torque, refer to RSU-7, "Components" .
CAUTION:
Do not reuse non-reusable parts.

Assemble disc rotor and wheel hub and bearing assembly by
aligning each matching mark as shown in the figure when install-
ing disc rotor.

Perform the final tightening of each of parts under unladen con-
ditions, which were removed when removing rear suspension
assembly. Check the wheel alignment. Refer to RSU-5, "
Wheel
Alignment Inspection" .

Adjust neutral position of steering angle sensor after checking
the wheel alignment. Refer to BRC-6, "
Adjustment of Steering
Angle Sensor Neutral Position" .

Check for the following after finishing work.
1. Washer 2. Mounting seal 3. Bushing (upper side)
4. Distance tube 5. Mounting bracket 6. Bushing (lower side)
7. Bound bumper cover 8. Bound bumper 9. Shock absorber
10. Axle assembly 11. Upper seat 12. Coil spring
13. Ball seat 14. Rubber seat 15. Cotter pin
16. Suspension arm 17. Connecting rod mounting bracket 18. Connecting rod
19. Mount stopper 20. Rear lower link 21. Front lower link
22. Radius rod 23. Stabilizer Bushing 24. Stabilizer Clamp
25. Stabilizer bar 26. Rear suspension member 27. Member stay
28. Stopper rubber 29. Cap 30. Rear pin stay
Refer to GI-11, "
Components" , for to the symbols in the figure.
SDIA2638E
SDIA2638E

REAR SUSPENSION ASSEMBLY
RSU-9
C
D
F
G
H
I
J
K
L
MA
B
RSU
Revision: 2007 April2007 M35/M45
–Parking brake operation (stroke): Refer to PB-3, "PEDAL STROKE" .
–Wheel sensor harness for proper connection: Refer to BRC-54, "WHEEL SENSOR" .

RSU-14
RADIUS ROD
Revision: 2007 April2007 M35/M45
RADIUS RODPFP:55110
Removal and InstallationNES000JD
REMOVAL
1. Remove tire with a power tool.
2. Remove brake caliper with a power tool. Hang it in a place where it will not interfere with work. Refer to
BR-28, "
REAR DISC BRAKE" .
CAUTION:
Do not depressing brake pedal while brake caliper is removed.
3. Put matching marks on both disc rotor and the wheel hub and
bearing assembly. then remove disc rotor.
4. Remove rear lower link and coil spring. Refer to RSU-16, "
REAR
LOWER LINK & COIL SPRING" .
5. Remove mounting bolt in lower side of shock absorber with a
power tool.
6. Remove mounting bolt and nut in axle side of front lower link
with a power tool.
7. Remove mounting bolt and nut in axle side of radius rod with a
power tool.
8. Remove mounting bolt in rear suspension member side of
radius rod with a power tool, then remove radius rod from vehicle.
INSPECTION AFTER REMOVAL
Check radius rod and bushing for any deformation, cracks, or damage. Replace if there are.
INSTALLATION

Installation is the reverse order of removal. For tightening torque. Refer to RSU-7, "Components" .
CAUTION:
Do not reuse non-reusable parts.

Assemble disc rotor and wheel hub and bering assembly by
aligning each matching mark as shown in the figure when install-
ing disc rotor.

Perform final tightening of rear suspension member and axle
installation position (rubber bushing) under unladen condition
with tires on level ground. Check wheel alignment. Refer to
RSU-5, "
Wheel Alignment Inspection" .

Adjust neutral position of steering angle sensor after checking
the wheel alignment. Refer to BRC-6, "
Adjustment of Steering
Angle Sensor Neutral Position" .
SDIA2638E
SDIA2638E

SB-1
SEAT BELTS
H RESTRAINTS
CONTENTS
C
D
E
F
G
I
J
K
L
M
SECTION SB
A
B
SB
Revision: 2007 April2007 M35/M45
SEAT BELTS
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precaution for Seat Belt Service .............................. 2
AFTER A COLLISION ........................................... 2
PRE-CRASH SEAT BELT .......................................... 3
Component Parts and Harness Connector Location ..... 3
System Description .................................................. 3
FUNCTION DESCRIPTION .................................. 4
FAIL-SAFE MODE ................................................ 4
CAN Communication System Description ................ 5
CAN Communication Unit ........................................ 5
Schematic ................................................................ 6
Wiring Diagram — PSB — ....................................... 7
Terminals and Reference Value for Pre-Crash Seat
Belt Control Unit ..................................................... 13
Work Flow .............................................................. 13
CONSULT-II Function (PRECRASH SEATBELT) ... 14
CONSULT-II START PROCEDURE .................... 14
HOW TO READ SELF-DIAGNOSTIC RESULTS ... 14
SELF-DIAGNOSTIC RESULTS ITEM CHART ... 14
DATA MONITOR ITEM CHART .......................... 14
Preliminary Check .................................................. 15
PRE-CRASH SEAT BELT OPERATION
INSPECTION ...................................................... 15
Diagnoses Symptom Chart .................................... 15
Check CAN Communication Circuit [U1000] .......... 15
Check Ignition Power Supply Circuit ...................... 16
Check Motor Power Supply and Ground Circuit
[B2454] ................................................................... 16
Check Seat Belt Buckle Switch (Driver Side) Circuit ... 18
Check Seat Belt Buckle Switch (Passenger Side)
Circuit ..................................................................... 20
Check Brake Pedal Stroke Sensor Circuit [B2453] ... 21
Check Pre-Crash Seat Belt Motor LH Circuit [B2452]
... 24
Check Pre-Crash Seat Belt Motor RH Circuit
[B2451] ................................................................... 26Check Brake Pedal Stroke Sensor Shield Wire Cir-
cuit .......................................................................... 27
Removal and Installation of Pre-Crash Seat Belt
Control Unit ............................................................. 28
REMOVAL ........................................................... 28
INSTALLATION ................................................... 28
SEAT BELTS ............................................................. 29
System Description ................................................. 29
SEAT BELT WARNING CHIME ........................... 29
SEAT BELT WARNING LAMP ............................. 29
Removal and Installation of Front Seat Belt ........... 29
REMOVAL OF SEAT BELT RETRACTOR .......... 29
INSTALLATION OF SEAT BELT RETRACTOR ... 30
REMOVAL OF SEAT BELT BUCKLE .................. 30
INSTALLATION OF SEAT BELT BUCKLE .......... 30
Removal and Installation of Rear Seat Belt ............ 31
REMOVAL OF SEAT BELT RETRACTOR .......... 31
INSTALLATION OF SEAT BELT RETRACTOR ... 31
REMOVAL OF SEAT BELT BUCKLE .................. 31
INSTALLATION OF SEAT BELT BUCKLE .......... 32
Seat Belt Inspection ................................................ 32
AFTER A COLLISION ......................................... 32
PRELIMINARY CHECKS .................................... 32
SEAT BELT RETRACTOR ON-VEHICLE
CHECK ................................................................ 33
SEAT BELT RETRACTOR OFF-VEHICLE
CHECK (FRONT SEAT BELT) ............................ 34
SEAT BELT RETRACTOR OFF-VEHICLE
CHECK (REAR SEAT BELT) ............................... 34
LATCH (LOWER ANCHORS AND TETHER FOR
CHILDREN) SYSTEM ............................................... 35
Removal and Installation ........................................ 35
REMOVAL ........................................................... 35
INSTALLATION ................................................... 35
TOP TETHER STRAP CHILD RESTRAINT ............. 36
Removal and Installation ........................................ 36
REMOVAL ........................................................... 36
INSTALLATION ................................................... 36

PRE-CRASH SEAT BELT
SB-3
C
D
E
F
G
I
J
K
L
MA
B
SB
Revision: 2007 April2007 M35/M45
PRE-CRASH SEAT BELTPFP:98845
Component Parts and Harness Connector LocationNHS0007X
System DescriptionNHS0007Y

Pre-crash seat belt system is adapted to front seat belts RH/LH.

When the pre-crash seat belt control unit judges the emergency braking operation, it gives the sense of
security by the motor built into the pre-crash seat belt retracting the shoulder belt and suppressing the
crew's posture change. Also, it eases the damage of the collision.
PHIA1123E
1. Fuse block (J/B) 2.Fuse, fusible link and relay block
(J/B)3.Pre-crash seat belt control unit B142
(View with the trunk side finisher LH
removed)
4.Brake pedal stroke sensor E125
(View with the instrument driver
lower panel removed)5.Pre-crash seat belt motor B32 (LH),
B422 (RH)
(View with the center pillar lower
garnish removed)6.Seat belt buckle switch B203 (driver
seat) B253 (passenger seat)