mirror INFINITI M35 2007 Factory Repair Manual

LT-4Revision: 2007 April2007 M35/M45 REMOVAL .........................................................230
INSTALLATION ..................................................230
Switch Circuit Inspection ......................................230
HAZARD SWITCH ..................................................231
Removal and Installation ......................................231
REMOVAL .........................................................231
COMBINATION SWITCH ........................................232
Wiring Diagram — COMBSW — ..........................232
Combination Switch Reading Function .................233
Terminals and Reference Values for BCM ............233
CONSULT-II Functions (BCM) ..............................238
CONSULT-II BASIC OPERATION .....................238
DATA MONITOR ................................................238
Combination Switch Inspection ............................239
Removal and Installation ......................................241
STOP LAMP ............................................................242
Wiring Diagram — STOP LAMP — ......................242
High-Mounted Stop Lamp .....................................244
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ..................................................244
Stop Lamp ............................................................244
BULB REPLACEMENT .....................................244
REMOVAL AND INSTALLATION .......................244
BACK-UP LAMP .....................................................245
Wiring Diagram — B/LAMP — .............................245
Bulb Replacement ................................................246
Removal and Installation ......................................247
REMOVAL .........................................................247
INSTALLATION ..................................................247
PARKING, LICENSE PLATE AND TAIL LAMPS ....248
Component Parts and Harness Connector Location .248
System Description ...............................................248
OUTLINE ...........................................................248
OPERATION BY LIGHTING SWITCH ...............249
COMBINATION SWITCH READING FUNCTION .249
EXTERIOR LAMP BATTERY SAVER CONTROL .249
CAN Communication System Description ............249
CAN Communication Unit .....................................249
Schematic .............................................................250
Wiring Diagram — TAIL/L — ................................251
Terminals and Reference Values for BCM ............256
Terminals and Reference Values for IPDM E/R ....257
How to Perform Trouble Diagnoses ......................257
Preliminary Check ................................................257
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................257
CONSULT-II Functions (BCM) ..............................258
CONSULT-II Functions (IPDM E/R) ......................258
Parking, License Plate and Tail Lamps Do Not Illu-
minate ...................................................................259
Parking, License Plate and Tail Lamps Do Not Turn
OFF (After Approx. 10 Minutes) ...........................263
License Plate Lamp ..............................................264
BULB REPLACEMENT .....................................264
Removal and Installation ......................................264
REMOVAL .........................................................264INSTALLATION ..................................................264
Front Parking (Clearance) Lamp ...........................264
BULB REPLACEMENT ......................................264
REMOVAL AND INSTALLATION .......................264
REAR COMBINATION LAMP .................................265
Bulb Replacement .................................................265
REAR TURN SIGNAL LAMP BULB, STOP/TAIL
LAMP BULB .......................................................265
Removal and Installation .......................................265
REMOVAL ..........................................................265
INSTALLATION ..................................................265
INTERIOR ROOM LAMP ........................................266
Component Parts and Harness Connector Location .266
System Description ...............................................266
ROOM LAMP TIMER BASIC OPERATION .......266
POWER SUPPLY AND GROUND .....................267
SWITCH OPERATION .......................................268
ROOM LAMP TIMER OPERATION ...................269
CONDITIONS FOR CANCELING TIMER ..........270
ROOM LAMP TIMER INAPPLICABLE LAMPS
OPERATION ......................................................270
INTERIOR ROOM LAMP BATTERY SAVER
FUNCTION ........................................................270
Schematic .............................................................271
Wiring Diagram — ROOM/L — .............................273
Terminals and Reference Values for BCM ............280
How to Perform Trouble Diagnoses ......................281
Preliminary Check .................................................282
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ...................................................................282
CONSULT-II Functions (BCM) ..............................283
CONSULT-II BASIC OPERATION .....................283
WORK SUPPORT (INT LAMP) .........................283
DATA MONITOR (INT LAMP) ............................284
ACTIVE TEST (INT LAMP) ................................285
WORK SUPPORT (BATTERY SAVER) .............285
DATA MONITOR (BATTERY SAVER) ...............285
ACTIVE TEST (BATTERY SAVER) ...................286
Interior Room Lamp Control Does Not Operate ....287
Map Lamp .............................................................289
BULB REPLACEMENT ......................................289
REMOVAL AND INSTALLATION .......................289
Personal Lamp ......................................................289
BULB REPLACEMENT ......................................289
REMOVAL AND INSTALLATION .......................289
Foot Lamp (Driver Side) ........................................290
BULB REPLACEMENT ......................................290
REMOVAL AND INSTALLATION .......................290
Foot Lamp (Passenger Side) ................................291
BULB REPLACEMENT ......................................291
REMOVAL AND INSTALLATION .......................291
Vanity Mirror Lamp ................................................291
BULB REPLACEMENT ......................................291
Step Lamp .............................................................292
BULB REPLACEMENT ......................................292
REMOVAL AND INSTALLATION .......................292
Kicking Plate Illumination ......................................292
BULB REPLACEMENT ......................................292

LT-268
INTERIOR ROOM LAMP
Revision: 2007 April2007 M35/M45

through front door lock assembly (driver side) (key cylinder switch) terminals 5 and 4

through grounds M16 and M70.
When a signal, or combination of door open signals is received by BCM, ground is supplied

to foot lamp driver side and passenger side terminals 2

to personal lamp LH and RH terminals 1

to map lamp terminal 2 and 5

through BCM terminal 48,

to step lamp (driver side, passenger side, rear LH and RH) terminals 2

to kicking plate illumination (driver side and passenger side) terminals 2

through BCM terminal 47.
With power and ground supplied, the interior lamps illuminate.
SWITCH OPERATION
When any front door switch is ON (door is opened), ground is supplied

to step lamp (driver side, passenger side, rear LH and RH) terminals 2

to kicking plate illumination (driver side and passenger side) terminals 2

through BCM terminal 47.
And power is supplied

through BCM terminal 41

to step lamp (driver side, passenger side, rear LH and RH) terminals 1

to kicking plate illumination (driver side and passenger side) terminals 1.
When any door switch is ON (door is opened) and personal lamp and map lamp is DOOR position, ground is
supplied

to personal lamp LH and RH terminal 1

to map lamp terminals 2 and 5

through BCM terminal 48.
And power is supplied

through BCM terminal 41

to personal lamp LH and RH terminals 3

to map lamp terminal 3.
When map lamp switch is ON, ground is supplied

to map lamp terminal 1

through grounds M16 and M70.
And power is supplied

through BCM terminal 41

to map lamp terminal 3.
When personal lamp LH and RH switch is ON, ground is supplied

to personal lamp LH and RH terminals 2

through grounds M16 and M70.
And power is supplied

through BCM terminal 41

to personal lamp LH and RH terminals 3.
When trunk lid lock assembly (trunk room lamp switch) is ON, ground is supplied

to trunk room lamp (upper and lower) terminals 2

through trunk lid lock assembly (trunk room lamp switch) terminals 1 and 2

through grounds B405 and B475.
And power is supplied

through BCM terminal 41

to trunk room lamp (upper and lower) terminals 1.
When vanity mirror lamp LH and RH switch is ON, ground is supplied

INTERIOR ROOM LAMP
LT-269
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2007 April2007 M35/M45

to vanity mirror lamp LH and RH terminals 2

through grounds M16 and M70.
And power is supplied

through BCM terminal 41

to vanity mirror lamp (LH and RH) terminals 1.
ROOM LAMP TIMER OPERATION
BCM controls applicable lamps to illuminate for 15 seconds (can be set maximum 30 seconds) by timer oper-
ation under following conditions. BCM also controls applicable lamps to brighten for 1 second (can be set max-
imum 5 seconds) when turned ON, or to dim for 3 seconds (can be set maximum 5 seconds) when turned
OFF. (Timer operating time and dimming/brightening time can be changed with CONSULT-II. Refer to LT- 2 8 3 ,
"WORK SUPPORT (INT LAMP)" .) This control operates as follows.
Applicable lamps

Room lamp system: map lamp, foot lamp (driver side and passenger side) and personal lamp (rear LH
and rear RH).
BCM controls room lamp timer operation under following condition.

Condition 1: Door lock state changes.*
BCM judges as the door lock is unlocked under either case below.
–The Intelligent Key unit sends door lock/unlock trunk open request signal (driver side unlock or passenger
side unlock) to BCM through CAN communication line by unlock operation of intelligent key, outside key
antenna and front door request switch (driver side) or outside key antenna and front door request switch
(passenger side).
–Key cylinder switch state (unlock) signal is sent to BCM through power window serial link when front door
lock assembly (driver side) (key cylinder switch) is unlocked (ON) by power window main switch unlock
operation.
And fulfills all the conditions below.
–The engine switch (push switch) is OFF.
–All the doors are closed.
*: This setting can be changed by CONSULT-II. Refer to LT- 2 8 3 , "
WORK SUPPORT (INT LAMP)" .

Condition 2: Any door switch state changes.*
The BCM terminal value of operated door switch is changed when any door is opened and then closed.
From that BCM judges as the door is opened and then closed.
And fulfills all the conditions below.
–The engine switch (push switch) is OFF.
–All the doors are closed.
*: This setting can be changed by CONSULT-II. Refer to LT- 2 8 3 , "
WORK SUPPORT (INT LAMP)" .

Condition 3: Engine switch (push switch) state changes.*
The Intelligent Key unit judges as the engine switch (push switch) is OFF and sends push-button ignition
switch (push switch) signal to PDU (power distribution unit) when push-button ignition switch (push
switch) turned OFF. Then PDU (power distribution unit) turns OFF, IGN power supply and ACC power
supply.
And fulfills the conditions below.
–All the doors are closed.
*:This setting can be changed by CONSULT-II. Refer to LT- 2 8 3 , "
WORK SUPPORT (INT LAMP)" .
NOTE:
When timer operation signal is input during former timer operation, BCM goes for latter timer operation.

LT-270
INTERIOR ROOM LAMP
Revision: 2007 April2007 M35/M45
ROOM LAMP TIMER OPERATING TIME
CONDITIONS FOR CANCELING TIMER
Timer operation is cancelled in any of the following conditions.

Driver door is locked.

Any door is opened.

Turn ignition switch is ACC or ON.
ROOM LAMP TIMER INAPPLICABLE LAMPS OPERATION

Step lamp system: step lamp (driver side, passenger side, rear LH and rear RH) and kicking plate illumi-
nation (driver side and passenger side).
Step lamp system lamps are ON/OFF linked with any door (driver side, passenger side, rear LH and rear
RH) opened and then closed.

Vanity mirror lamp LH and RH.
Operated side vanity mirror lamp is ON/OFF linked with vanity mirror opened and then closed.

Trunk room lamp (lower) and trunk room lamp (upper).
Trunk room lamps (lower and upper) are ON/OFF linked with trunk opened and then closed.
INTERIOR ROOM LAMP BATTERY SAVER FUNCTION
Applicable lamps

Room lamp system: map lamp, foot lamp (driver side and passenger side) and personal lamp (rear LH
and rear RH).

Step lamp system: step lamp (driver side, passenger side, rear LH and rear RH) and kicking plate illumi-
nation (driver side and passenger side).

Vanity mirror lamp LH and RH.

Trunk room lamp (lower) and trunk room lamp (upper).
If the any applicable lamp is left illuminated, BCM turns OFF the battery saver output power supply 30 or 60
minutes to prevent run down of the battery. (Factory setting time is 30 minutes. And timer setting can be
changed by CONSULT-II. Refer to LT- 2 8 5 , "
WORK SUPPORT (BATTERY SAVER)" .)

When the push-button ignition switch (push switch) is turned from ON to OFF, the timer is activated.

If any of the following door switch signal condition is changed with the push-button ignition switch (push
switch) in OFF position, the timer is activated when the change is occurred.
Door switch signals (driver side, passenger side, rear LH and RH), front door lock assembly (driver side) (key
cylinder switch) signal and Intelligent Key unlock signal.
SKIB4934E

INTERIOR ROOM LAMP
LT-291
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2007 April2007 M35/M45
Foot Lamp (Passenger Side)NKS003TC
BULB REPLACEMENT
1. Insert a screwdriver or similar tool and remove lens (1).
2. Remove bulb (2).
REMOVAL AND INSTALLATION
Removal
1. Use a clip driver or similar tool and remove foot lamp (passenger
side) (1).
2. Disconnect connector.
Installation
Installation is the reverse order of removal.
Vanity Mirror LampNKS003TD
BULB REPLACEMENT
1. Insert a thin screwdriver in the lens end and remove lens (1).
2. Remove bulb (2).Foot lamp (Passenger side) : 12V - 3.4W
SKIB4204E
SKIB4205E
Vanity mirror lamp : 12V - 1.8 W
SKIB4197E

LT-294
ILLUMINATION
Revision: 2007 April2007 M35/M45
ILLUMINATION OPERATION BY LIGHTING SWITCH
With the lighting switch in the 1ST or 2ND position (or if the auto light system is activated), the BCM receives
input signal requesting the illumination lamps to illuminate. This input signal is communicated to the IPDM E/R
across the CAN communication lines. The CPU located in the IPDM E/R controls the tail lamp relay coil,
which, when energized, directs power

through IPDM E/R terminal 21

to combination meter terminal 13

to LDW switch (illumination) terminal 5 (with lane departure warning)

to VDC off switch (illumination) terminal 3

to trunk lid opener switch (illumination) terminal 3

to combination switch (spiral cable) terminal 24

to door mirror remote control switch (illumination) terminal 16

to AFS switch (illumination) terminal 5 (with AFS)

to rear sunshade front switch (illumination) terminal 5 (with rear control switch)

to A/T illumination terminal 1

to snow mode switch (illumination) terminal 5 (AWD models)

to rear control cancel switch (illumination) terminal 4 (with rear control switch)

to clock terminal 3

to multifunction switch terminal 3

to audio unit terminal 9

to DVD player terminal 18 (with DVD player)

to NAVI control unit terminal 61 (with navigation system)

to AV control unit terminal 61 (without navigation system)

to climate controlled seat switch driver side (illumination) terminal 7 (with climate controlled seat)

to climate controlled seat switch passenger side (illumination) terminal 7 (with climate controlled seat)

to ashtray illumination (rear LH) terminal 1

to ashtray illumination (rear RH) terminal 1

to illumination control switch terminal 1

to cigarette lighter socket (illumination) terminal 2

to map lamp (illumination) terminal 8

to power window main switch illumination terminal 1

to glove box lamp terminal 1

to rear control switch terminal 2

to rear power seat switch RH (illumination) terminal 4 (with rear control switch)

to rear heated seat switch RH (illumination) terminal 7 (with rear control switch)

to rear sunshade cancel relay terminal 6 (with rear control switch)

to automatic return cancel switch (illumination) terminal 4 (with rear control switch)

to rear power seat switch LH (illumination) terminal 4 (with rear control switch) and

to rear heated seat switch LH (illumination) terminal 7 (with rear control switch),

through Intelligent Key unit terminal 12

to push button ignition switch (illumination) terminal 3.
Ground is supplied

to combination meter terminal 14

to combination meter terminal 9, 10 and 11

to push button ignition switch (illumination) terminal 2

to LDW switch (illumination) terminal 4 (with lane departure warning)

to VDC off switch (illumination) terminal 4

to trunk lid opener switch (illumination) terminal 4

to combination switch (spiral cable) terminal 25

ILLUMINATION
LT-295
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2007 April2007 M35/M45

to door mirror remote control switch (illumination) terminal 15

to AFS switch (illumination) terminal 6 (with AFS)

to rear sunshade front switch (illumination) terminal 6 (with rear control switch)

to A/T illumination terminal 2

to snow mode switch (illumination) terminal 6 (ADW models)

to rear control cancel switch (illumination) terminal 5 (with rear control switch)

to clock terminal 4

to multifunction switch terminal 4

to audio unit terminal 8

to DVD player terminal 17 (With DVD player)

to climate controlled seat switch driver side (illumination) terminal 8 (with climate controlled seat) and

to climate controlled seat switch passenger side (illumination) terminal 8 (with climate controlled seat)

through illumination control switch terminal 2

to illumination control switch terminal 3

through grounds M16 and M70,

to cigarette lighter socket (illumination) terminal 1

to map lamp (illumination) terminal 4

to power window main switch illumination terminal 2 and

to glove box lamp terminal 2

through grounds M16 and M70,

to ashtray illumination (rear RH) terminal 2

through grounds B402, B405,

to ashtray illumination (rear LH) terminal 2

to automatic return cancel switch (illumination) terminal 2 (With rear control switch)

to rear power seat switch LH (illumination) terminal 3 (With rear control switch)

to rear heated seat switch LH (illumination) terminal 8 (With rear control switch)

through grounds B5, B40 and B131,

through rear sunshade cancel relay terminal 7(With rear control switch)

to rear sunshade rear switch (illumination) terminal 7 (With rear control switch)

through grounds B5, B40, B131 and B559.

to rear control switch terminal 4

to rear power seat switch RH (illumination) terminal 3 (With rear control switch)

to rear heated seat switch RH (illumination) terminal 8 (With rear control switch)

through grounds B5, B40, B131 and B559.
With power and ground supplied, illumination lamps illuminate.
EXTERIOR LAMP BATTERY SAVER CONTROL
BCM activates the exterior lamp battery saver control function and turns off the exterior lamps to prevent bat-
tery from over discharge when the combination switch (lighting switch) is in 1ST or 2ND position and/or the
front fog lamp switch ON and the door lock operation is performed by keyless entry system.
CAN Communication System DescriptionNKS003TI
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNKS003TJ
Refer to LAN-50, "CAN System Specification Chart" .

BULB SPECIFICATIONS
LT-313
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2007 April2007 M35/M45
BULB SPECIFICATIONSPFP:26297
HeadlampNKS003TQ
Exterior LampNKS003TR
Interior Lamp/IlluminationNKS003TS
NOTE:
This lamp is used as both front ashtray and front cigarette lighter.Item Wattage (W)
Low (Halogen type)55 (H1)
Low (Xenon type)35 (D2S)
High60 (HB3)
Item Wattage (W)
Front combination lampFront turn signal lamp 21
Parking lamp 5
Front side marker lamp 5
Rear combination lampStop/Tail lamp LED
Rear turn signal lamp 21 (amber)
Rear side marker lamp LED
Back-up lamp18
Side turn signal lamp5
Front fog lamp55 (H11)
License plate lamp5
High-mounted stop lampLED
Item Wattage (W)
Map lamp8
Personal lamp8
Trunk room lampUpper
5
Lower
Front ashtray and front cigarette lighter illumination
NOTE1.4
Rear ashtray illumination1.4
Ste p lamp5
Vanity mirror lamp1.8
Center console indirect illuminationLED
Glove box lamp1.4
Foot lampDriver side
3.4
Passenger side
Kicking plateDriver side
LED
Passenger side
Power window indirect illuminationLED

PG-96
HARNESS
Revision: 2007 April2007 M35/M45
ETC3 EC Electric Throttle Control Motor
F/FOG LT Front Fog Lamp
F/PUMP EC Fuel Pump
FPCM EC Fuel Pump Control Module
FTS AT A/T Fluid Temperature Sensor Circuit
FTTS EC Fuel Tank Temperature Sensor
FUELB1 EC Fuel Injection System Function (Bank 1)
FUELB2 EC Fuel Injection System Function (Bank 2)
H/LAMP LT Headlamp
HORN WW Horn
HSEAT SE Heated Seat
I/KEY BL Intelligent Key System
I/MIRR GW Inside Mirror (Auto Anti-Dazzling Mirror)
IATS EC Intake Air Temperature Sensor
ICC ACS Intelligent Cruise Control System
ICC/BS EC ICC Brake Switch
ICC/SW EC ICC Steering Switch
ICCBOF EC ICC Brake Switch
IGNSYS EC Ignition System
ILL LT Illumination
INJECT EC Injector
IVCB1 EC Intake Valve Timing Control Solenoid Valve Bank 1
IVCB2 EC Intake Valve Timing Control Solenoid Valve Bank 2
IVCSB1 EC Intake Valve Timing Control Position Sensor Bank 1
IVCSB2 EC Intake Valve Timing Control Position Sensor Bank 2
IVTB1 EC Intake Valve Timing Control System (Bank 1)
IVTB2 EC Intake Valve Timing Control System (Bank 2)
KS EC Knock Sensor
LDW DI Lane Departure Warning System
MAFS EC Mass Air Flow Sensor
MAIN AT Main Power Supply and Ground Circuit
MAIN EC Main Power Supply and Ground Circuit
METER DI Speedometer, Tachometer, Temp., Oil and Fuel Gauges
MIL/DL EC MIL & Data Link Connector
MIRROR GW Door Mirror
MMSW AT Manual Mode Switch
NATS BL Nissan Anti-Theft System
NONDTC AT Non-Detective Items
O2H2B1 EC Heated Oxygen Sensor 2 Heater Bank 1
O2H2B2 EC Heated Oxygen Sensor 2 Heater Bank 2
O2S2B1 EC Heated Oxygen Sensor 2 Bank 1
O2S2B2 EC Heated Oxygen Sensor 2 Bank 2
P/SCKT WW Power Socket
PDU PG Power Distribution Unit Code Section Wiring Diagram Name

SE-1
SEAT
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION SE
A
B
SE
Revision: 2007 April2007 M35/M45
SEAT
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Service Notice .......................................................... 3
Precautions for Work ................................................ 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
AUTOMATIC DRIVE POSITIONER ...........................11
Component Parts And Harness Connector Location
.... 11
System Description ................................................ 12
MANUAL OPERATION ....................................... 12
MEMORY OPERATION ...................................... 12
EXITING OPERATION ........................................ 14
ENTRY OPERATION .......................................... 14
INTELLIGENT KEY INTERLOCK OPERATION ... 15
FAIL-SAFE MODE .............................................. 15
INITIALIZATION PROCEDURE .......................... 16
SETTING CHANGE FUNCTION ......................... 16
CAN Communication System Description .............. 16CAN Communication Unit ....................................... 16
Schematic ............................................................... 17
Wiring Diagram — AUT/DP — ............................... 19
Terminals and Reference Values for BCM .............. 31
Terminals and Reference Value for Intelligent Key
Unit ......................................................................... 31
Terminals and Reference Values for Driver Seat
Control Unit ............................................................. 32
Terminals and Reference Values for Automatic
Drive Positioner Control Unit .................................. 34
CONSULT-II Function (AUTO DRIVE POS.) .......... 37
CONSULT-II START PROCEDURE .................... 37
SELF-DIAGNOSIS RESULTS ............................. 37
DATA MONITOR ................................................. 38
ACTIVE TEST ..................................................... 39
WORK SUPPORT ............................................... 39
Work Flow ............................................................... 40
Symptom Chart ....................................................... 40
CAN Communication Inspection Using CONSULT-
II (Self-Diagnosis) ................................................... 42
Check BCM Power Supply and Ground Circuit ...... 42
Check Driver Seat Control Unit Power Supply and
Ground Circuit ........................................................ 43
Check Automatic Drive Positioner Control Unit
Power Supply and Ground Circuit .......................... 44
Check Sliding Motor Circuit .................................... 45
Check Reclining Motor Circuit ................................ 46
Check Front Lifting Motor Circuit ............................ 47
Check Rear Lifting Motor Circuit ............................. 49
Check Telescopic Motor Circuit .............................. 50
Check Tilt Motor Circuit .......................................... 51
Check Sliding Sensor Circuit .................................. 53
Check Reclining Sensor Circuit .............................. 55
Check Front Lifting Sensor Circuit .......................... 57
Check Rear Lifting Sensor Circuit .......................... 59
Check Telescopic Sensor Circuit ............................ 61
Check Tilt Sensor Circuit ........................................ 63
Check Door Mirror Sensor LH Circuit ..................... 64
Check Door Mirror Sensor RH Circuit .................... 67
Check Sliding Switch Circuit ................................... 69