INFINITI QX30 2017 Owner's Manual

3. Fix the protective plate to the underside ofthe battery without any overlap
2.
4. Fit the replacement battery in the vehicle.
REINITIALISATION PROCEDURE AFTER
BATTERY RECONNECTION
If the battery has been reconnected, check the
following items:
•Clock setting (if so equipped). For details,
see Clock in the2. Instruments and con-
trols section, or the separately provided
navigation system Owner’s Manual, or the
audio device descriptions in Audio system
(if equipped) in the4. Display screen,
heater and air conditioner, and audio sys-
tem section.
•Reset the desired radio stations to the preset
station buttons. For details, see the audio
device descriptions in the “4. Heater and air
conditioner, and audio system”.
JUMP-STARTING
If jump-starting is necessary, see Jump
starting in the6. In case of emergency sec-
tion. If the engine does not start by jump
starting, the battery may have to be replaced. It
is recommended that you visit an INFINITI re-
tailer for this service.
WARNING
Be sure the ignition switch is in the OFF posi-
tion before servicing drive belt. The engine
could rotate unexpectedly.
1. Visually inspect each belt for signs of un- usual wear, cuts, fraying or looseness. If the
belt is in poor condition or loose, have it
replaced or adjusted. It is recommended that
you visit an INFINITI retailer for this service.
2. Have the belts checked regularly for condi- tion and tension in accordance with the
maintenance schedule as shown in a sepa-
rately provided Warranty Information and
Maintenance booklet.
NDI1635
DRIVE BELT
8-12Do-it-yourself

Replace the spark plugs according to the main-
tenance schedule shown in a separate mainte-
nance booklet.
If replacement is required, it is recommended
that you visit an INFINITI retailer.
Always replace spark plugs with recommended
or equivalent ones.
WARNING
Be sure the engine and ignition switch are off
and that the parking brake is engaged
securely.
CAUTION
•Be sure to use the correct socket to remove
the spark plugs. An incorrect socket can
cause damage to the spark plugs.It is recommended that you visit an INFINITI
retailer if checking or replacement is required.
WARNING
•Operating the engine with the air cleaner
filter off can cause you or others to be
burned. The air cleaner filter not only cleans
the intake air, it also stops the flame if the
engine backfires. If the air cleaner is not
installed and the engine backfires, you
could be burned. Never drive with the air
cleaner filter off. Be cautious working on the
engine when the air cleaner is off.
•Never pour fuel into the throttle body or
attempt to start the engine with the air
cleaner removed. Doing so could result in
serious injury.
CLEANING
If the windshield or rear window is not clear
after using the window washer or if a wiper
blade chatters when running, wax or other
material may be on the blade or windshield.
Clean the outside of the windshield or rear
window with a washer solution or a mild deter-
gent. The windshield or rear window is clean if
beads do not form when rinsing with clear
water.
Clean the blade by wiping it with a cloth soaked
in a washer solution or a mild detergent. Then
rinse the blade with clear water. If the wind-
shield or rear window is still not clear after
cleaning the blades and using the wiper, re-
place the blades.
CAUTION
Worn windshield wiper blades can damage the
windshield and impair driver vision.
SPARK PLUGS
AIR CLEANER FILTERWIPER BLADES
Do-it-yourself8-13

REPLACING FRONT WINDOW WIPER
BLADES
Replace the wiper blades if they are worn. To
replace the windshield wiper blades, follow the
procedure below:1. Move the wiper arm away from the wind-
shield.
2. Press both release clips
2.
3. Move the wiper blade
1in the direction of
arrow
3away from wiper arm4.
4. Remove wiper blade
1in the direction of
arrow
5.
5. Position new wiper blade
1with recess6on lug5.
6. Move wiper blade
1in the direction of
arrow
3onto the wiper arm until retaining
clips
2engage in bracket4.
NDI1586NDI1587
8-14Do-it-yourself

7. Make sure that wiper blade1is seated
correctly.
8. Move the wiper arm back onto the wind- shield.
CAUTION
•After wiper blade replacement, return the
wiper arm to its original position; otherwise
it may be damaged when the hood is
opened.
•Make sure the wiper blades contact the
glass; otherwise the arms may be damaged
from wind pressure. If you wax the surface of the engine hood, be
careful not to let wax get into the washer nozzle
A. This may cause clogging or improper wind-
shield washer operation. If wax gets into the
nozzle, remove it with a needle or small pin
B.
REPLACING REAR WINDOW WIPER BLADE
Replace the wiper blades if they are worn. To
replace the rear window wiper blade, follow the
procedure below:
1. Move wiper arm
4away from the rear
window.
NDI892Z
NDI1588
Do-it-yourself8-15

2. Press both release clips2.
3. Move wiper blade
1in the direction of
arrow
3away from wiper arm4.
4. Remove wiper blade
1in the direction of
arrow
5.
5. Position new wiper blade
1with recess6on lug5.
6. Move wiper blade
1in the direction of
arrow
3onto the wiper arm until retaining
clips
2engage in bracket4. 7. Make sure that wiper blade
1is seated
correctly.
8. Move the wiper arm back onto the rear window.
NDI1589
8-16Do-it-yourself

If the brakes do not operate properly, it is
recommended that you have the brakes
checked. It is recommended that you visit an
INFINITI retailer for this service.
SELF-ADJUSTING BRAKES
Your vehicle is equipped with self-adjusting
brakes. The disc-type brakes self-adjust every
time the brake pedal is applied.Blown fuses must be replaced with fuses of the
same rating, which you can recognise by the
color and fuse rating. The fuse ratings are listed
in the fuse allocation chart.
If the newly inserted fuse also blows, have the
cause traced and rectified. It is recommended
you visit an INFINITI retailer for this service.
The fuses in your vehicle disconnect faulty
circuits. if a fuse blows, all the components on
the circuit and their functions will fail.
BEFORE REPLACING A FUSE
•Secure the vehicle against rolling away.
•Switch off all electrical consumers.
•Remove the key from the ignition lock.
The fuses are located in various fuse boxes:
•Fusebox in the engine compartment on the
left-hand side of the vehicle, when viewed in
the direction of travel.
•Fuse box in the front-passenger footwell.
The fuse allocation chart is on the fuse box in
the front-passenger footwell.
ENGINE COMPARTMENT
WARNING
Never use a fuse of higher or lower amperage
rating than that specified on the fuse box
cover. This could damage the electrical system
or electronic control units or cause a fire.
BRAKES FUSES
Do-it-yourself8-17

1. Open the hood
2. Remove any existing moisture from the fusebox using a dry cloth
3. To open: open clamps
2.
4. Fold cover
1up in the direction of the arrow
and remove it. To close:
1. Check whether the seal is lying correctly in
cover
1.
2. Insert cover
1at the back into openings3on the fuse box. 3. Fold down cover
1.
4. Hook clamps into the fuse box and close
5. Close the hood.
PASSENGER COMPARTMENT
WARNING
Never use a fuse of higher or lower amperage
rating than that specified on the fuse box
cover. This could damage the electrical system
or electronic control units or cause a fire.
NDI1591NDI1592
8-18Do-it-yourself

To open:
1. Open the front-passenger door.
2. Remove the floor mats.
3. Fold out perforated floor covering
1in the
direction of the arrow. 4. To release cover
3press retaining clamp
2.
5. Fold out cover
3in the direction of the arrow
to the catch.
6. Remove cover
3forwards.
NOTE
Fuse allocation chart
4is located on the lower
right-hand side of cover
3. To close:
1. Insert cover
3on the left-hand side of the
fuse box into the retainer. Cover
3engages
in the retainers.
2. Fold down cover
3until clamps2lock
audibly.
3. Fold back perforated floor covering
1.
4. Fit the floor mats.
NDI1593NDI1594
Do-it-yourself8-19

CAUTION
Be careful not to allow children to swallow the
battery or removed parts.
CHECKING THE BATTERY
Press the(LOCK) or(UNLOCK)
button.
The battery is working properly if the battery
check lamp
1lights up briefly.
The battery is discharged if the battery check
lamp
1does not light up briefly. Replace the
battery.
NOTE
•If the key battery is checked within the signal
reception range of the vehicle, pressing the
(LOCK) or(UNLOCK) button locks
or unlocks the vehicle.
•You can obtain a battery from an INFINITI
retailer.
REPLACING THE BATTERY
You require a CR 2025 3 V cell battery.
Replace the battery in the Intelligent Key as
follows:
1. Take the emergency key element out of the key (see Mechanical key in the
3. Pre-driving checks and adjustments sec-
tion)
2. Press emergency key element
2into the
opening into the key in the direction of the
arrow until the battery cover
1opens.
When doing so, do not hold cover
1shut.
3. Remove battery tray cover
1.
NPA1474NPA1472
INTELLIGENT KEY BATTERY REPLACEMENT
8-20Do-it-yourself

4. Repeatedly tap the key against your palmuntil battery
1falls out. 5. Insert the new battery with the positive
terminal facing upwards. Use a lint-free cloth
to do so.
6. Make sure that the surface of the battery is free of lint, grease and other contamination.
7. Insert the front tabs of battery cover
1and
then press to close it.
8. Insert emergency key element into the key (see Mechanical key in the3. Pre-driving
checks and adjustments section).
9. Check the function of all key buttons on the vehicle.
If you need assistance with replacement, it is
recommended that you visit an INFINITI retailer
for this service. FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
NPA1473SPA0784Z
Do-it-yourself8-21