set clock INFINITI QX30 2018 Owners Manual

1Permanent display: depending on vehicle
specification: outside temperature or
speed
2Time
3Text field
4Menu bar
5Drive program
6Shift lever position
Text field
3shows the selected menu or
submenu as well as display messages.
NOTE
Set the time using the INFINITI controller
and the [Settings] menu available in the cen-
tral display (see "Clock settings" in the "4.
Display screen, heater and air conditioner,
and audio system" section).
MENUS AND SUBMENUS
To call up the menu bar4and select a menu,
press theorbutton on the steer-
ing wheel. Menu bar
4disappears after a
few seconds.
Depending on the equipment fitted in the
vehicle, you can call up the following menus:
•[Trip] menu
•[Navi] menu (navigation instructions)
•[Audio] menu
•[DriveAssist] menu
•[Serv.] menu
•[Settings] menu
The [Audio] and [Navi] menus differ slightly
in vehicles with an audio system and in ve-
hicles with a navigation system. The ex-
amples given in this Owner's Manual apply to
vehicles equipped with navigation.
[Trip] menu
Standard display:
Press and hold the
button on the steer-
ing wheel until the [Trip] menu with trip meter
1and total distance recorder2is shown.
NIC2752NIC2753
2-16Instruments and controls

indicator light in the combination meter also
lights up.
If you are driving at speeds below approxi-
mately 28 MPH (45 km/h) or other road
users are detected or the roads are ad-
equately lit The high beam headlights are
switched off automatically. The
indica-
tor light in the combination meter goes out.
The
indicator light in the vehicle infor-
mation display remains lit.
To deactivate:
Move the combination switch back to its nor-
mal position The
indicator light in the
vehicle information display goes out.
HEADLIGHTS MISTED UP ON
THE INSIDE
Certain climatic and physical conditions may
cause moisture to form in the headlight. This
moisture does not affect the functionality of
the headlight.
INSTRUMENT BRIGHTNESS
CONTROL
The light sensor in the combination meter
automatically controls the brightness of the
instrument panel
In daylight, the displays in the combination
meter are not illuminated
The lighting in the combination meter, dis-
plays and controls in the vehicle interior can
be adjusted using the brightness control
knob.
The brightness control knob
1is located
behind the steering wheel.
Turn the brightness control knob clockwise or
counterclockwise. If the light switch is set to
orthe brightness is dependent
upon the brightness of the ambient light.
FRONT FOG LIGHTS
In conditions where visibility is poor due to
fog, snow or rain, the fog lights improve vis-
ibility as well as making it easier for other
road users to see you. They can be operated
together with the side lights or together with
the side lights and low beam headlights.
To switch on the fog lights:
•Turn the ignition switch to the ON position
or start the engine.
•Turn the light switch toor <AUTO>.
•Press thebutton. The greenindicator light in the combination meter
lights up
NIC2615NIC2699
FOG LIGHT SWITCH (IF SO
EQUIPPED)
2-70Instruments and controls

WARNING
To avoid personal injury, keep your hands,
fingers and head away from the sunshade
arm, the arm rail and sunshade inlet port.
NOTE
The following notes cover situations where
strong sun shining on the roof of the vehicle
causes the area around the sunshade motor
to reach high temperatures:
•If the temperature of the sunshade motor
reaches a value between 185 °F (85 °C)
and 212 °F (100 °C), “restricted mode” is
enabled, and the sunshade will only be
allowed to CLOSE.
•If the temperature of the sunshade motor
exceeds 212 °F (100 °C), the sunshade will
not operate.
Opening and closing
Manual control:
To close the sunshade, press and hold the
“CLOSE” side of the switch
1To stop the
sunshade from closing fully, release the
switch. To open the sunshade press and hold the
“OPEN” side of the switch
2To stop the
sunshade from opening fully, release the
switch.
Automatic operation:
To fully open or close the sunshade auto-
matically, press briefly on the open or close
side of the switch and then release. To stop
the sunshade from opening or closing, press
either side of the switch.
Auto-reverse function:
When the control unit detects something
caught by the sunshade, the sunshade will
open automatically.
NOTE
The auto-reverse function remains active
whether the sunshade is being closed manu-
ally or automatically. If the battery cable is disconnected, the clock
will need to be re-adjusted to the correct
time.
ADJUSTING TIME
Set the time using the INFINITI controller and
the [Settings] menu available in the central
display (see &#34;Clock settings&#34; in the &#34;4. Display
screen, heater and air conditioner, and audio
system&#34; section).
NOTE
On vehicles fitted with a navigation system,
the clock is automatically updated via GPS.
The initial clock setting may be incorrect.
NSD659
CLOCK
Instruments and controls2-77

Clock settings
Clock settings can be changed.
1. Push <MENU>.
2. Touch [Settings].
3. Touch [Clock].
Setting itemAction
[On-Screen Clock] Set the clock display on/off. When this item is on, the clock display appears.
[Daylight Savings Time] Select the setting for the daylight saving time from ON, OFF or Auto*. Each time this item is touched the
setting is changed.
[Clock Format (24h)] Toggle the clock format between 12-hour and 24-hour clocks. When the indicator light illuminates, the
clock is set to the 24-hour format.
[Time Zone] Select an appropriate time zone from the destination list. If [Auto]* is selected, the system selects the time
zone automatically.
[Offset Adjustment]* Adjust the offset value (hour and minutes).
[>]** [Time Adjustment] Adjust the time by increasing or decreasing the value.
[Calendar Adjustment] Adjust the year, month, and day.
*: For models with navigation system.
**: For models without navigation system.
Time is synchronized to the combination meter once the calendar setting is set.
Display screen, heater and air conditioner, and audio system4-15

AIR CONDITIONING SYSTEM
1Sets the temperature
2De-ices/defogs the windshield
3Set the air distribution
4Activates/deactivates air-recirculation
mode
5Sets the airflow
6Activates/deactivates cooling with air
dehumidification
7Switches the rear window defroster on/
off
Operating tips
A number of tips and recommendations for
optimum use of the air-conditioning system
are listed below:
•Switch on the air-conditioning system by
turning control knob
5clockwise to the
desired position (except position 0)
•Set the temperature to 70°F(22°C)
•Recommendation for avoiding misted
windows at low exterior temperatures or
in rain: switch on the
cooling with
dehumidification function. Set air distribu-
tion to
and if possible switch offand. Deactivate air-
recirculation mode.
Set airflow control
5to a setting be-
tween 3 and 6.
•Recommendation for rapid cooling or
heating of the vehicle interior: briefly set
airflow control
5to a setting between 3
and 6.
•Recommendation for a constant vehicle
interior temperature: set airflow control
5to a setting between 1 and 3.
NAA1644
4-44Display screen, heater and air conditioner, and audio system

•Recommendation for air distribution in
winter: select theandsettings.
Recommendation for air distribution in
summer: select the
orandsettings.
•Only use the &#34;Windshield demisting&#34; func-
tion briefly until the windshield is clear
again
•Only use air-recirculation mode briefly, for
example if there are unpleasant outside
odors or when in a tunnel. The windows
could otherwise mist up as no fresh air is
drawn into the vehicle in air-recirculation
mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds
at the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of
the various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on: turn control
5clockwise to the
desired position (except position 0).To switch off:
turn control
5counter-
clockwise to position 0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate the &#34;Cooling with air dehu-
midification&#34; function, the air inside the ve-
hicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the &#34;Cooling with air
dehumidification&#34; function briefly.
The &#34;Cooling with air dehumidification&#34; func-
tion is only available when the engine is run-
ning. The air inside the vehicle is cooled and
dehumidified according to the temperature
selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This
is normal and not a sign that there is a mal-
function.
To activate:
Press the
button The indicator light in
thebutton lights up.
To deactivate:
Press the
button. The indicator light in
thebutton goes out. The cooling with
air dehumidification function has a delayed
switch-off feature. Problems with the &#34;Cooling with air dehu-
midification&#34; function:
Problem:
The indicator light in the
but-
ton flashes three times or remains off. The
cooling with air dehumidification function
cannot be activated.
Cause and solution: The cooling with air de-
humidification function has been deactivated
due to a malfunction. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise.
Only change the temperature setting in small
increments. Start at 70°F(22°C).
Display screen, heater and air conditioner, and audio system4-45

Setting the air distribution
Directs the airflow through the demis-ter ventilators.
Directs the airflow through the centerand side air ventilators.
Directs the airflow through the foot-
well air ventilators.
NOTE
•You can also activate several of the air
distribution settings simultaneously. In or-
der to do this, press several of the air dis-
tribution buttons. The air is then routed
through different air ventilators.
•Regardless of the air distribution setting,
airflow is always directed through the side
air ventilators. The side air ventilators can
only be closed if the adjusters are turned
clockwise until they engage.
To set air distribution:
1. Make sure the engine is running.
2. Press one or more of the
,,orbuttons. The corresponding indica-
tor light comes on.
Setting the airflow
1. Make sure the ignition switch is in the ON position. 2. To increase or reduce airflow: turn control
5counterclockwise or clockwise.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.
NOTE
You should only select the &#34;Windshield de-
misting&#34; function until the windshield is clear
again.
Activating the &#34;Windshield demisting&#34;
function:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indi-
cator light in thebutton lights up.
The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode off NOTE
•The &#34;Windshield demisting&#34; function auto-
matically sets the blower output to the
optimum demisting effect. As a result, the
airflow may increase or decrease auto-
matically after the
button is pressed.
•You can adjust the blower output manu-
ally while the &#34;Windshield demisting&#34; func-
tion is in operation. Turn airflow control
5counterclockwise or clockwise.
Deactivating the &#34;Windshield demisting&#34;
function:
Press the
button. The indicator light in
thebutton goes out. The previous set-
tings are reactivated. Air-recirculation mode
remains deactivated.
or
Turn temperature control
1counterclock-
wise or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate the
&#34;Cooling with air dehu-
midification&#34; function.
2. If the windows continue to mist up, acti- vate the
&#34;Windshield demisting&#34;
function.
4-46Display screen, heater and air conditioner, and audio system

To activate:
Press the
button The indicator light in
thebutton lights up.
To deactivate:
Press the
button. The indicator light in
thebutton goes out. The cooling with
air dehumidification function has a delayed
switch-off feature.
Problems with the &#34;Cooling with air dehu-
midification&#34; function:
Problem: The indicator light in the
but-
ton flashes three times or remains off. The
cooling with air dehumidification function
cannot be activated.
Cause and solution: The cooling with air de-
humidification function has been deactivated
due to a malfunction. Have the system
checked. It is recommended you visit an
INFINITI retailer for this service.
Setting automatic climate control
to automatic mode
Only automatic climate control features the
&#34;Control climate control automatically&#34; func-
tion.
In automatic mode, the set temperature is
maintained automatically at a constant level
The system automatically regulates the tem- perature of the dispensed air, the airflow and
the air distribution.
The automatic mode functions optimally
when the &#34;Cooling with air dehumidification&#34;
function is activated. If desired, cooling with
air dehumidification can be deactivated.
If you deactivate the &#34;Cooling with air-
dehumidification&#34; function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can mist up more quickly. There-
fore, only deactivate the &#34;Cooling with air-
dehumidification&#34; function briefly.
To set climate control to automatic mode:
Make sure the ignition switch is in the ON
position.
Set the desired temperature.
To activate: press the
button The indi-
cator light in thebutton lights up. Au-
tomatic air distribution and airflow are acti-
vated.
To switch to manual mode: press the
orbutton
or
Press the
orbutton. The indicator
light in thebutton goes out. Automatic
air distribution and airflow are deactivated.
Setting the temperature
Different temperatures can be set for the
driver&#39;s and front-passenger sides. The set
temperature is automatically maintained at a
constant level.
Make sure the ignition switch is in the ON
position.
To increase or reduce temperature: turn con-
trol
1or9counterclockwise or clockwise.
Only change the temperature setting in small
increments. Start at 70°F(22°C).
Setting the air distribution
Directs the airflow through the demis- ter ventilators.
Directs the airflow through the centerand side air ventilators.
Directs the airflow through the foot-
well air ventilators.
Directs the airflow through the center and side air ventilators as well as the
footwell air ventilators.
Directs the airflow through the centerand side air ventilators as well as the
demister ventilators.
Directs the airflow through the foot-
well and demister ventilators.
Directs the airflow through the demis- ter ventilators, the center and side air
ventilators as well as the footwell air
ventilators.
4-50Display screen, heater and air conditioner, and audio system

NOTE
Regardless of the air distribution setting,
airflow is always directed through the side
air ventilators. The side air ventilators can
only be closed if the adjusters are turned
clockwise until they engage.
To set the air distribution:
1. Make sure the engine is running.
2. Press the
orbutton repeat-
edly until the desired symbol appears in
the display.
Setting the airflow
1. Make sure the ignition switch is in the ON position.
2. To increase or reduce airflow: press the
orbutton.
Switching the ZONE function
on/off
This function is only available with automatic
climate control.
To activate: press the
button. The in-
dicator light in thebutton lights up. The
temperature setting for the driver&#39;s side is not
adopted for the front-passenger side.
To deactivate: press the
button. The
indicator light in thebutton goes out. The temperature setting for the driver&#39;s side
is adopted for the front-passenger side.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.
NOTE
You should only select the &#34;Windshield de-
misting&#34; function until the windshield is clear
again.
Activating the &#34;Windshield demisting&#34;
function:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indi-
cator light in thebutton lights up.
The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode off NOTE
•The &#34;Windshield demisting&#34; function auto-
matically sets the blower output to the
optimum demisting effect. As a result, the
airflow may increase or decrease auto-
matically after the
button is pressed.
•You can adjust the blower output manu-
ally while the &#34;Windshield demisting&#34; func-
tion is in operation. Press the
orbutton.
Deactivating the &#34;Windshield demisting&#34;
function:
Press the
button. The indicator light in
thebutton goes out. The previous set-
tings are reactivated Air-recirculation mode
remains deactivated.
or
Turn temperature control
1or9counter-
clockwise or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate the
&#34;Cooling with air dehu-
midification&#34; function.
2. Activate automatic mode
.
3. If the windows continue to mist up, acti- vate the
&#34;Windshield demisting&#34;
function.
Display screen, heater and air conditioner, and audio system4-51

CAUTION
•To use Mobile Apps, the INFINITI
InTouch App must be installed and run-
ning on the compatible smartphone.
This App can be downloaded from the
iTunes APP Store or the Google Play
store.
•Mobile Apps also require an active sub-
scription and valid INFINITI Owner Por-
tal account. Please see
www.infinitiusa.com/InfinitiInTouch/
support/ (for United States) or
www.infiniti.ca/InfinitiInTouch (for
Canada) for more information
•Communication fees may be charged
depending on the contents of the con-
tract between the user and the cellular
phone carrier.
•Before using this service, some applica-
tions may require individual subscrip-
tions.
•For some applications, the system may
not support all functions of the applica-
tions that are installed on your smart-
phone. Additionally, due to service pro-
vider policies, the contents of
application services may be changed or
terminated.
•If the smartphone is outside the net-
work range, some functions cannot be
used.
•While driving, some operations are lim-
ited in order to prevent distracting the
driver. While driving, avoid looking at
the display.
•Before changing ownership of the ve-
hicle, delete application data (Email
data, etc.) stored on the in-vehicle de-
vice. It is also recommended that you call
your INFINITI customer center to notify
them of change of ownership.
•Some application services may be sub-
ject to change or be terminated without
prior notice.
USING APPLICATIONS
NOTE
To use Apps functions on models without
navigation system, please complete the cal-
endar setting from Clock setting screen.
&#34;Clock settings&#34; in the &#34;5. Starting and driving&#34;
section
Main operation
Push <MENU> and touch [Apps] to display
the Apps screen.
Touch the icon for the preferred application.
The selected application will be launched.
•The applications shown on the menu
screen and the display order can be cus-
tomized.
&#34;App Garage Settings screen&#34; later in this
section
•Some applications can be set to launch
automatically as the ignition switch is
turned on.
VEHICLE APPS
Vehicle Apps are unique applications devel-
oped by INFINITI that can be downloaded
and installed on the in-vehicle hardware.
NOTE
The INFINITI InTouch App must be installed
and running on a compatible smartphone in
order to download updates or use Vehicle
Apps that require a network connection. See
&#34;Getting user ID and password&#34; later in this
section.
Display screen, heater and air conditioner, and audio system4-99