INFINITI QX56 2004 Factory Service Manual

EI-10
SQUEAK AND RATTLE TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
SBT 8 44

CLIP AND FASTENER
EI-11
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
CLIP AND FASTENERPFP:76906
DescriptionEIS002X6

Replace any clips and/or fasteners which are damaged during removal or installation.
Symbol
No.Shapes Removal & Installation
C101
C103
C203
CE103
CG104
CE114—
CG101
SBF302HSBF367BA
SBT095SBF423H
SBF258GLIIA0236E
SBF104BSBF147B
LIIA0237ESBF352C
SBF353C
SBF145BSBF085B

EI-12
CLIP AND FASTENER
Revision: August 20072004 QX56
CR103
CS101
CF118
C205 Symbol
No.Shapes Removal & Installation
SBF768BSBF770B
SBF078BSBF992G
LIIA1341ELIIA1342E
LIIA1344ELIIA1345E

FRONT BUMPER
EI-13
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
FRONT BUMPERPFP:F2022
Removal and InstallationEIS002X7
REMOVAL
1. Remove side screws from fascia assembly.
2. Remove screws from front of fender protector. Refer to EI-23, "
FENDER PROTECTOR" .
1. Lower energy absorber 2. Front bumper side bracket RH 3. Front bumper stay RH
4. Upper bumper reinforcement 5. Plastic clip 6. Upper energy absorber (part of
upper bumper reinforcement)
7. Fastener 8. Front fascia assembly 9. Front fascia bracket
10. Front undercover 11. Fog/turn lamp 12. Fog/turn lamp LH/RH finisher
13. Spring nut 14. Front bumper stay LH 15. Front bumper side bracket LH
16. Plastic clip 16. Headlamp finisher (RH shown)
WIIA0260E

EI-14
FRONT BUMPER
Revision: August 20072004 QX56
3. Remove engine undercover.
4. Remove fog/turn lamp finisher and fog/turn lamp.

Disconnect harnesses.
5. Remove engine underside cover.
6. Remove fasteners, release clips and remove front fascia assembly.
7. Remove plastic clips and remove upper energy absorber.
8. Remove upper bumper reinforcement.
9. Remove plastic clips and remove lower energy absorber.
10. Remove front bumper stays and front bumper side brackets, LH and RH.
INSTALLATION
Installation is in the reverse order of removal.

REAR BUMPER
EI-15
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
REAR BUMPERPFP:H5022
Removal and InstallationEIS002X8
WIIA0261E

EI-16
REAR BUMPER
Revision: August 20072004 QX56
1. Remove quarter panel trim covers LH and RH.
2. Disconnect sonar sensor harness connector under rear fascia assembly.
3. Release retainer clips on both sides of rear fascia assembly with a 1/4 turn and top S clips and remove
fascia assembly.
4. Remove energy absorber.
5. Remove reinforcement assembly.
6. Remove nuts and remove retainer assembly.

Remove S clips from retainer assembly.
7. Disconnect sonar sensors from sonar sensor retainers.
8. Remove sonar sensors and harness from rear fascia assembly.

Disconnect sonar sensors from harness.

Remove sonar sensor retainers from rear fascia assembly.
9. Remove bolts on each side of tow hitch and remove tow hitch.
10. Remove drafter duct from under LH quarter panel.
Installation is in the reverse order of removal.
1. Retainer assembly 2. Plastic clip 3. S clip
4. Reinforcement assembly 5. Energy absorber 6. Sonar sensor
7. Quarter panel trim cover LH 8. Drafter duct 9. Retainer clip
10. Rear fascia assembly 11. Sonar sensor retainer 12. Tow hitch
13. Sonar sensor harness 14. Quarter panel trim cover RH

FRONT GRILLE
EI-17
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
FRONT GRILLEPFP:62310
Removal and InstallationEIS002X9
1. Remove bolts and nuts attaching grille.
2. Remove grille.
Installation is in the reverse order of removal.
WIIA0565E

EI-18
COWL TOP
Revision: August 20072004 QX56
COWL TOPPFP:66100
Removal and InstallationEIS002XA
1. Remove right and left wiper arms. Refer to WW-29, "Removal and Installation of Front Wiper Arms,
Adjustment of Wiper Arms Stop Location" .
2. Remove cowl top seal.

Release plastics clips on cowl top seal which go through cowl tops LH and RH and cowl top extension.
3. Remove cowl top covers LH and RH.

Release plastic clips under cowl top covers attaching to grommets on hoodledge.

Disconnect washer tubes from washer nozzles under cowl top covers.
4. Remove cowl top extension brackets LH and RH.

Disconnect wiper motor harness from cowl top extension bracket LH.

Cowl top extension bracket LH must be removed prior to removal of wiper motor and connecting rod
assembly.
1. Grommet 2. Plastic clip 3. Cowl top RH
4. Cowl top seal 5. Drain tube 6. Cowl top extension bracket RH
7. Cowl top extension 8. Cowl top extension bracket LH 9. Cowl top LH
LIIA1288E

COWL TOP
EI-19
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
5. Remove wiper motor and connecting rod linkage. Refer to WW-29, "Removal and Installation of Wiper
Motor and Linkage" .
6. Disconnect windshield washer tube. Refer to WW-31, "
Washer Tube Layout" .
7. Remove water cut valve bracket from cowl top extension. Refer to CO-17, "
THERMOSTAT AND WATER
PIPING" .
8. Remove A/C line bracket from cowl top extension, Refer to ATC-162, "
REFRIGERANT LINES" for ATC
and ATC-162, "
REFRIGERANT LINES" for MTC.
9. Remove drain tube from each side of cowl top extension.
10. Remove cowl top extension.
Installation is in the reverse order of removal.